American Standard 1662643.295 Installation Guide
Contents
1. SEAL 2 should be tight against finished wall Ea 1 2 NPSM A950646 90mm 3 1 2 1660 741 1 2 NPT APPLY SEALANT OR TEFLON TAPE INSTALL LOWER SUPPORT BRACKET The SLIDE BAR works best when secured to the wall studs or cross brace using the WOOD SCREWS If a mounting into the studs is not possible use appropriate wall fasteners to provide secure installation Mark a vertical center line in the location you wish to install the SLIDE BAR NOTE The height from the finished floor is optional See rough in drawing for suggested dimensions Determine desired height from the finished floor to the lower support and mark a horizontal center line Place the MOUNTING BRACKET 1 on the center lines with a pencil mark the location on the mounting FINISHED holes to be drilled Fig A J Son E Using 15 64 diameter drill Drill two mounting holes 1 max deep Fig B E Install the two ANCHORS 2 provided into the mounting holes Use a hammer to lightly tap ANCHORS 2 into place Make sure they are installed flush with the finished wall Place the MOUNTING BRACKET 1 over the ANCHORS 2 and secure the MOUNTING BRACKET 1 with the SCREWS 3 provided Fig C INSTALL SLIDE BAR Slide the COVER 1 onto the MOUNTING BRACKET 2 flush against the wall Fig A Install the bottom of SLIDE BAR 3 into the MOUNTING BRACKET 2 IMPORTANT The slot at the bottom of the slide bar must face toward the wall Rotate the sl2. ALL HOSE AND HAND SHOWER E Align the ESCUTCHEON and SPACER Install SEAL 1 into COUPLING NUT 2 Connect so that the spacer is sitting on the L COUPLING NUT 2 to WALL SUPPLY NIPPLE 3 A R E and tighten ESCUTCHEON ESCUTCHEON E Rotate the upper ESCUTCHEON and INSTALL second SEAL 4 into SPRAY HOSE SPACER 1 on SLIDE BAR 2 until END 5 and connect HAND SHOWER 6 to the three snap arms align with the SPRAY HOSE END 5 holes in the cover Push ESCUTCHEON Hand tighten and SPACER 1 into COVER 3 until it snaps in place E Repeat above steps to snap the lower ESCUTCHEON andSPACER 4 into place CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE M968637 Rev 1 4
3. SHOWER SYSTEM KITS Installation Instructions 1662 SERIES Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended Tools amp Materials f Hammer Phillips Screwdriver ROUGHING IN DIMENSIONS 32mm 1 174 2 1 16 48 60 OPTIONAL TO FINISHED BLGOR Es 1 2 NPSM HOSE CONNECTION RUBBER GASKET __ FINISHED WALL 1660 236 65mm 849mm 2 1 72 383 3 8 240mm 9 1 2 10 1 2 OPTIONAL TO FINISHED FLOOR 86mm USUALLY BETWEEN 3 3 8 915mmT0 1525mm FINISHED FLOOR 36 60 INSTALL WALL SUPPLY i e Certified to comply with ANSI A112 18 1 M968637 Rev 1 4 6mm 15 64 Drill Bit p Pencil Electric Drill 1660 500 1 2 NPSM 67mm lt 42 5 8 146mm 5 3 4 1660 502 1660 505 1 2 NPSM gt 1 2 NPSM 247mm 9 3 4 9 7 8 1660 638 Turn off hot and cold water supplies before beginning Supply to WALL SUPPLY 1 is 1 2 NPT See rough in above for detailed information Install RUBBER SEAL 2 onto WALL SUPPLY 1 Apply sealant or teflon tape to threads of 1 2 NPT supply nipple Thread WALL SUPPLY 1 onto supply nipple making a water tight seal WVALL SUPPLY 1 with RUBBER
4. ide bar until it locks into place and cannot be turned Fig B LOCATE UPPER MOUNTING BRACKET Install the upper MOUNTING BRACKET 1 onto the SLIDE BAR 2 Align the MOUNTING BRACKET 1 with center lines and mark the center mounting hole with a pencil as shown Fig A E Remove the SLIDE BAR 2 and set a side Using 15 64 diameter drill bit drill mounting hole 1 max deep Fig B er Se eet INSTALL UPPER MOUNTING BRACKET Install the ANCHOR 1 provided into the mounting hole Make sure it is installed flush with the finished wall Use a hammer to lightly tap ANCHOR 1 into place Place the MOUNTING BRACKET 2 over the ANCHOR 1 and secure the MOUNTING BRACKET 2 with the SCREW 3 provided NOTE Do not tighten fully Slide the MOUNTING BRACKET 2 up against the bottom of the mounting slot M Slide the COVER 4 onto the MOUNTING BRACKET 2 flush against the wall BOTTOM OF MOUNTING SLOT M968637 Rev 1 4 INSTALL SLIDE BAR INTO MOUNTING BRACKETS E Install the SLIDE BAR 1 back into the lower MOUNTING BRACKET 2 IMPORTANT The slot at the bottom of the slide bar must face toward the wall Rotate the slide bar until it locks into place and cannot be turned Fig A E Push top COVER 3 and MOUNTING BRACKET 4 down onto top of SLIDE BAR 1 Fig A E Tighten MOUNTING SCREW 5 with phillips screw driver to secure assembly to wall Fig B FINISH INSTALLATION INST
Download Pdf Manuals
Related Search