Vigo VG6061CHCL36W Installation Guide
Contents
1. MAKE SURE TO LEAVE A GAP OF 3 8 10MM FROM THE BOTTOM OF THE GLASS INSIDE OF SHOWER HEX SCREW SIDE GLASS PANEL GASKET OUTSIDE OF SHOWER GLASS SUPPORT 7 VIEW FROM THE TOP FIG 6 MODEL VG06061 D INSTALLING THE WATER SEAL STRIP TO DOOR PANEL ut 1 Clean the door glass panel 13 edge where the door side seal strip 14 is to be installed with rubbing alcohol 2 SEE FIG 7 3 Verify that the soft flange of the seal strip faces toward the inside of the shower cabin before seal strip installation 4 Install the seal strip according to the diagram See Note A Leave the extra top of the seal strip that is overlapping the glass and cut at finish of install NOTES 1 If the seal strip is not flat or twisted use hot water and a hair dryer to apply minimal heat and press the seal strip back into position 2 Part 414 is reversible and pre cut on top and bottom to fit in proper configuration Cutting finishing is needed but only after fully installing and only at the top of the unit 3 The door magnetic seal strip 410 and the side seal strips 46 will be 10mm shorter than the side glass panel This is to compensate for the depth of the bottom rail The door magnetic seal strip 410 is reversible and will need to be cut at top for best aesthetic approach THIS SIDE MUST LOOK INSIDE THE CABIN MAKE SURE TO LEAVE A GAP OF 3 8 10MM FROM THE BOTTOM OF THE GLASS NOTE2. NOTE You may need to add more than one shim per hinge as glass hole openings vary during production PVC shims prevent the door from sagging due to gravity and the weight of the door I Never install without shims this can cause the glass to break causing property damage and bodily harm DOOR O oe 250mm E BOTTOM mm ON FIG 8 A HINGE 8 ER OUTSIDE OF THIN p THIN GASKET GASKETS 7 SEAL STRIP 14 nZ Fi o SIDE GLASS PANEL 4 EN DOOR 13 THIN EJ GASKET PLATE INSIDE OF THE CABIN HEX SCREW VIEW FROM INSIDE VIEW FROM THE TOP FIG 8A 11 MODEL VG06061 INSTALLING SIDE GLASS PANEL PART 5 VISO Install the side seal strip 46 to the wall side of the side glass panel 45 Install the magnetic side seal strip 10 to the door side The magnetic side should be facing the outside and the clear side be facing the inside Be sure to place the seal strip 6 10mm from the bottom of the glass SEE FIG 9 Installing the magnetic seal strip prior to locating the place for the glass support allows for proper seal You may need to adjust the magnetic seal strip placement after full install to guarantee proper placement on the top of the corner joint It should rest tight on the corner joint in order to prevent water leakage Screw in the glass support to the side glass panel using the hex key supplied making sure to slide it back as far as possible from the glass before y
3. during the warranty period conclusive evidence e g proof of purchase or installation is provided to the foregoing by the user proving that the failure occurred or was discovered within the warranty period an authorized independent service person or company representative has been permitted to inspect the product during regular business hours within a reasonable time after the problem was reported by the user VIGOs warranty obligation shall be discharged upon tender of replacement or repair The customer s refusal to accept the tender terminates VIGO s warranty obligations Certain models are pending approval Certification may be ended by VIGO or certification agencies without notice 18 MODEL VG06061
4. A MAKE SURE TO LEAVE A GAP OF 3 8 10MM FROM THE BOTTOM OF THE GLASS THIS SIDE MUST LOOK INSIDE THE 4 CABIN 13 FIG 7 SEAL STRIP INSTALLATION DIAGRAM 10 MODEL VG06061 WARNING DOOR PANEL INSTALLATION REQUIRES TWO OR MORE PEOPLE TO ASSIST E INSTALLING THE DOOR Make sure you have the door right side up The distance at the top is slightly larger than the distance at the bottom SEE FIG 8 2 Clean the door 13 glass surfaces where the hinges 8 are to be installed with rubbing alcohol 3 Place magnetic seal strip 410 to the panel The magnetic side should be facing the inside and the clear side be facing the outside Make sure the seal is level with the bottom of the panel Do not install the handle first this is dangerous and may cause the glass to break Install the top hinge first for safety and ease of install 4 Position the door onto the hinges Hold securely in place using shims The seal 414 may get stuck between the two panels of glass Pull the seal out of the groove using your fingers and nothing sharp making sure not to damage the seal Tighten allen key screws 5 Install the hinges as illustrated SEE FIG 8A Use the hex key supplied 6 Adjust hinge so the gaps are equal at top and bottom and pull door panel away from side panel to allow the door to swing freely without crimping seal strip 414 7 Lift door panel to be level with hinge panel Use PVC shims provided to hold firmly in place
5. LARGER OF THE SIDE RAILS IS YOUR HINGE BASE RAIL THE LARGER OF THE 2 RAILS GOES WITH GLASS PANEL 4 SEE FIG 1A TO MATCH CONFIGURATION THE DIFFERENCE IS MINIMAL PLEASE REVIEW PRIOR TO INSTALL LEFT SIDE DOOR OPENING FIG 1A RIGHT SIDE DOOR OPENING Remove the aluminum cover from the front piece of the bottom rail by sliding it out Remove top of the corner joint Slide the bottom corner joint 2 pieces 11 onto the bottom rail 3 pieces 9 SEE FIG 3 Align the bottom rail and corner joint to the desired position on the shower base Make sure the A and B distances are correct see page 3 for A and B distances Prior to drilling dry fit everything making sure that everything is straight level and plum Pre drill for sinkers and tap sinkers Cut excess sinker off with hacksaw or sharp blade Dip screws in silicone SEE FIG 2A Screw corner joints and rails down Silicone tops of screws seal the bottom rail with clear silicone caulk and center its sides to the base Clip the aluminum cover to the front piece of the bottom rail making sure the lower side faces the inside of the shower SEE FIG 3A Silicone the underneath portion of the corner joint caps and put them on the corner joints SEE FIG 3A 6 MODEL VG06061 VIGD STUD THIS EDGE LOOKS gt INSIDE OF THE SHOWER TOP REMOVES TO INSTALL 3 4 SCREW N e THIS EDGE LOOKS Se 11 ud OUTSIDE OF THE SHOWER TE Fann mn A FIG 3 ALUMIN
6. ED TO THE RIGHT OR LEFT SIDE THE TEXTURED SIDE OF THE MATTE GLASS UNIT SHOULD ALWAYS BE INSTALLED ON THE OUTSIDE OF THE UNIT AND IS NOT REVERSIBLE SEE CONFIGURATION DIAGRAM BELOW 13 13 oo 5 oo 4 o 4 FRONT GLASS DOOR PANEL SIDE GLASS SIDE GLASS DOOR PANEL FRONT GLASS PANEL PANEL PANEL PANEL FIG 1 GLASS CONFIGURATION DIAGRAM LEFT SIDE DOOR OPENING RIGHT SIDE DOOR OPENING MODEL VG06061 kh PREPARATION STEPS TO FOLLOW BEFORE INSTALLATION 1 2 3 Y Remove the plastic layer from the base border if needed Do NOT remove the plastic layer off the plastic platform of the base Properly apply silicone to the wall and base joints Make sure to read corresponding base instructions carefully prior to install on the Vigo Brand Shower Door System Failure to do so can cause water leakage and bodily harm IMPORTANT To prevent damage to the finish you should protect the shower cabin bottom with a cardboard protector before beginning the installation Ensure that there is sufficient structural support behind the shower wall to hold the weight of the shower door If there is insufficient support then reinforce the shower walls with wooden studs prior to shower door installation SEE FIG 3 CAUTION GASKETS NEED TO BE IN BETWEEN ALL GLASS AND METAL CONTACT FAILURE TO DO SO CAN LEAD TO BREAKAGE AND POTENTIAL BODILY HARM INSTALLATION STEPS A INSTALLING THE BOTTOM RAIL PLEASE NOTE THAT WHEN INSTALLING THE
7. FFECTIVE JANUARY 1 2010 VIGO offers the following limited warranty on each of its Shower Enclosure products the Product and the components thereof This warranty extends only to the original owner or end user for personal household use For commercial uses additional limitations apply VIGO warrants the structural glass component of the Product to be free from defects in workmanship and materials under normal use and service for the period commencing from the initial date of purchase by the owner or end user contractor or builder from VIGO or an authorized VIGO dealer through the lifetime of the original owner or end user VIGO warrants the hardware components of the Product to be free from defects in workmanship and materials under normal use and service for a period of two 2 years from the initial date of purchase by the owner or end user contractor or builder from VIGO or an authorized VIGO dealer VIGO warrants the seal strip components of the Product to be free from defects in workmanship and materials under normal use and service for a period of one 1 year from the initial date of purchase by the owner or end user contractor or builder from VIGO or an authorized VIGO dealer Subject to the Warranty Service provision below any product reported to the authorized dealer or to VIGO as being defective within the warranty period will be repaired or replaced with a product of equal value at the option of VIGO This warranty exten
8. ING HEX SCREW COVERS 1 Install hex screw covers 21 to the hex screws that mount the hinges wall connectors and glass supports N IMPORTANT e WAIT 24 HOURS BEFORE USING SHOWER DO NOT ALLOW WATER TO DIRECTLY HIT DOOR SEAL STRIPS 15 MODEL VG06061 VG06061 LEFT DOOR VG06061 RIGHT DOOR MODEL VG06061 CLEANING INSTRUCTIONS FOR THE SHOWER CABIN AND DOOR PANEL A 000 Use mild liquid household cleaners to keep metal surface bright and clean Rinse well and dry with a clean cloth Remove dust with a soft damp cloth Use rubbing alcohol to clean and remove grease oil paint and ink Accidental scratches or stains will rarely show If they do show they can be easily removed with a liquid automobile polish N IMPORTANT Do NOT use abrasive cleaners scrapers metal brushes or any items products that would scratch and or dull surface Do NOT allow surface to come into contact with acetone nail polish remover dry cleaning solution lacquer thinner gasoline or any other similar product MAINTENANCE INSTRUCTIONS FOR THE SHOWER CABIN AND DOOR PANEL A If you are experiencing water build up in the top portion of the rail it is recommended to drill small holes on the top inside portion Space holes every 6 8 Stay within 3 from the end of the rail SEE FIG 16 OUTSIDE OUTSIDE 17 MODEL VG06061 VIGD VIGO INDUSTRIES LLC VIGO SHOWER ENCLOSURE LIMITED LIFETIME WARRANTY E
9. LASS AND HARDWARE NO SHOWER BASE FULLY INSTALLED MODEL DIM A DIM B DIM C DIM D HEIGHT 4 SIDE GLASS 5 SIDE GLASS 13 DOOR 97007 PANEL 97001 PANEL 97006 GLASS AND HARDWARE WITH CORRESPONDING VIGO BRAND BASE VG06068 FULLY INSTALLED PANEL 97001 PANEL 97006 we GLASS AND HARDWARE WITH CORRESPONDING VIGO BRAND BASE VG06069 FULLY INSTALLED MODEL DIM A DIM B DIM C DIM D HEIGHT 4 SIDE GLASS 5 SIDE GLASS 13 DOOR 97007 PANEL 97001 PANEL 97006 42 X 42 42 1 8 42 1 8 22 1 2 27 3 4 78 3 4 20 1 2 x71 5 8 20 1 4 x71 5 8 25 7 8 x70 3 8 40 X 40 40 1 4 40 1 4 21 1 2 261 4 78 3 4 19 1 2 X71 5 8 19 1 4 X71 5 8 24 1 2 X70 3 8 38 X 38 38 1 8 38 1 8 19 1 2 26 3 8 78 3 4 17 1 2 X71 5 8 17 1 4 X71 5 8 24 1 2 X70 3 8 36 X 36 36 1 8 36 1 4 17 1 2 263 8 78 3 4 15 1 2 X71 5 8 15 1 4 X71 5 8 24 1 2 X70 3 8 A B C amp D DIMENSIONS WERE MEASURED AFTER SHOWER ENCLOSURE WAS COMPLETELY INSTALLED MODEL VG06061 WARNING 9 WE STRONGLY RECOMMEND THAT A LICENSED PROFESSIONAL INSTALL THIS SHOWER a CABIN AND INCLUDE THE ASSISTANCE OF A SECOND PERSON TO INSTALL THE DOOR UNIT INSTALLATION OF THE SHOWER DOORS BY AN INEXPERIENCED PERSON MAY RESULT IN GLASS BREAKAGE AND CONSEQUENTLY CAUSE PERSONAL INJURY OR DEATH BEFORE STARTING Compare items on your invoice with what you have received Carefully review t
10. UM COVER INSIDE INSIDE ran CORNER JOINT CAP OUTSIDE OUTSIDE FIG 3A MODEL VG06061 HINGE INSTALLATION VIGD 1 Clean the glass surface on the side glass panel 4 where the hinges 8 are to be installed with rubbing alcohol 2 Position hinges on the side glass panel SEE FIG 4 Place a shim between the glass and the hinge on the bottom The metal should not rest on the glass SEE FIG 4A 3 Place gaskets on each side of the side glass panel Screw the hinges to the side glass panel with the hex key supplied SCREW THIS HALF OF THE HINGE TO THE SIDE GLASS PANEL SCREW THIS HALF OF THE HINGE TO THE DOOR THIS SIDE OF THE HINGE IS LOOKING FROM THE INSIDE OF THE CABIN SIDE GLASS PANEL 4 THIN GASKETS VIEW FROM INSIDE OF THE CABIN FIG 4 HINGE 8 INSIDE VIEW SIDE GLASS PANEL 4 PVC SHIMS FIG 4A SCREW THIS HALF OF THE HINGE TO THE SIDE GLASS PANEL SCREW THIS HALF OF THE HINGE TO THE DOOR THIS SIDE OF THE HINGE IS LOOKING FROM THE OUTSIDE OF THE CABIN SCREW THIS HALF OF THE HINGE TO THE DOOR 1 SCREW THIS HALF OF THE HINGE TO THE SIDE GLASS PANEL THIS SIDE OF THE HINGE LOOKS OUTSIDE OF THE CABIN VIEW FROM OUTSIDE OF THE CABIN PVC SHIMS SIDE GLASS PANEL 4 INSIDE VIEW MODEL VG06061 C k e di INSTALLING SIDE GLASS PANEL PART 4 Arrange glass to the preferred configuration see diagram on pa
11. VIGO VIGO INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE MODEL VG06061 SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information Always observe the instructions indicated by these symbols N WARNING Instructions that if ignored could result in death or serious personal injury caused by incorrect handling or installation of the product These instructions must be observed for safe installation N CAUTION The instructions for the following unit is based off of the Vigo brand shower base The instructions can not be provided for any other installation other than that of the Vigo brand The warranty will be voided if the following was not performed properly O IMPORTANT Maintenance and other important non personal injury and non material damage instructions or statements that should be observed It is highly advised to dry fit the unit prior to any installation INSTALLATION INSTRUCTIONS FOR STANDING SHOWER CABIN Vo OWNER S MANUAL PLEASE READ INSTRUCTIONS BEFORE PROCEEDING Packing List Wall connector 2pc Structural arm 2pc Support assembly 2pc Side glass panel with hinge slots 1pc Side glass panel without hinge slots 1pc Side seal strip 2pc Glass support 4pc Hinge 2pc Bottom rail 3 pc 10 Door magnetic seal strip 2pc 11 Bottom corner joint 2pc 12 Handle assembly 1pc 19 13 Door 1pc 14 Door side sea
12. ages caused thereby or resulting thereof either directly or indirectly The owner end user must provide access to the components of the Product as described in the installation guide so that VIGO can execute the warranty specified herein If such access is not available all expenses to provide said access will be the responsibility of the owner end user This warranty does not apply to Products that have not been installed or operated in accordance with instructions supplied by VIGO and all applicable rules regulations and legislation pertaining to such installations This warranty does not apply unless the VIGO Product is installed by fully insured licensed professionals Vigo strongly recommends that such licensed professionals have experience in the installation of bathroom and kitchen products Installation of certain products including without limitation glass products i e shower doors and glass sinks by an inexperienced person may result in glass breakage and consequently cause personal injury or death VIGO is not liable for personal injuries or deaths to any persons or for any direct special incidental or consequential damage loss of time loss of profits inconvenience incidental expenses labor or material charges or any other costs resulting from the use of the product or equipment or pertaining to the application of the present warranty or resulting from the removal or replacement of any product or element or part covered by
13. ds to the original owner or end user and is not transferable to a subsequent owner Neither the distributor authorized VIGO dealer nor any other person has been authorized to make any affirmation representation or warranty other than those contained in this warranty Any affirmation representation or warranty other than those contained in this warranty shall not be enforceable against VIGO or any other person VIGO reserves the right to modify this warranty at any time it being understood that such modifications will not alter the warranty conditions applicable at the time of sale of the products in question Limitations This warranty shall not apply to instances of incorrect operating procedures breakages or damages caused by fault through improper installation carelessness abuse misuse misapplication improper maintenance or alteration of the Product as well as chemical or natural corrosion accident fire flood an act of God or any other casualty Avoid abrasive cleaners steel wools and harsh chemicals as these will scratch damage and or dull the product and or finish and void this warranty The owner end user of the Product covered by the present warranty is entirely responsible for its proper installation and any applicable plumbing or electrical wiring VIGO neither installs nor supervises the installation nor hires a contractor for this purpose consequently VIGO cannot be held responsible for any default breakage or dam
14. ew it in to the wall with 1 1 8 screws 16 Slide the structural arm 2 into the wall connector 1 Tighten all set screws Repeat Steps 1 through 6 to install the other support assembly to the other side glass panel FIG 11 13 MODEL VG06061 H INSTALLING PRE CUT BOTTOM DOOR SEAL STRIP o 1 Clean the door glass panel 13 edge where the door bottom side seal strip 15 is to be installed with rubbing alcohol 2 SEE FIG 12 3 Verify that the soft flange of the seal strip faces toward the inside of the shower cabin before seal strip installation 4 Install the seal strip according to the diagram NOTE If the seal strip is not flat or twisted use hot water and a hair dryer to apply minimal heat and press the seal strip back into position 13 10 OUTSIDE OF INSIDE OF THE CABIN A VA 15 APPLYING THE SILICONE Apply clear silicone caulking to the inside between the wall and side seal strip 2 Apply clear silicone caulk to the inside between the bottom of side glass panels 44 45 and bottom rail 3 Apply clear silicone caulk around the inside perimeter of the bottom rail SEE FIG 13 4 Apply clear silicone caulk to the seal strip connections of the door bottom seal strip and the door magnetic seal strip SEE FIG 13A Do el mb a 14 MODEL VG06061 FIG 13A J HANDLE INSTALLATION 1 Assemble the door handles 12 to the door 13 SEE FIG 14 FIG 14 K INSTALL
15. ge 5 These instructions are for a right side door opening configuration Select the door opening location on the shower cabin Install the side seal strip 46 to the wall side of the hinged side glass panel 4 SEE FIG 5 Screw in the glass support 7 to the side glass panel using the hex key supplied making sure to slide it back as far as possible from the glass before you tighten The part that connects to the wall should face in SEE FIG 6 Be sure to use gaskets on both sides of the panel The glass holes are elliptical allowing for 5mm out of square N If your shower stall is out of square more than 5mm from the top of the glass to the bottom of the glass then this can cause the shower to potentially leak and can cause potential fatal harm Make sure glass panel is level to the wall Be sure to install the correct glass with the correct rail SEE FIG 1A Place the side glass panel onto the bottom rail 49 Use the level to position the side glass panel correctly Make sure the seal strip is against the wall Mark holes on the wall for the mounting screws Remove the side glass panel Drill holes into respective marks and insert plastic anchors 20 inside them N Not necessary if installing into studs Studs are the preferred means of installation anchors can pull out of the wall causing property damage and bodily harm Replace the front glass panel back onto the bottom rail and screw it to the wall with 1 5 8 screws 17
16. he Packing List on page 2 If any items are missing contact Vigo Industries at 1 866 591 7792 REQUIRED TOOLS Square and or Phillips 41 and 42 screwdriver Flat head screwdriver Electric drill plus 1 4 and 5 16 drill bit depending on wall Level Measuring tape Pencil non permanent Clear silicone caulking Utility knife WARNING o Handle fragile items with care to prevent injury or material damage Glass on panels and doors is tempered glass and must never be cut to prevent personal injury 5 IMPORTANT e Fiberglass or acrylic construction might not be sufficiently strong enough to support the shower door enclosure You should use the wood framing studs from behind the face edge of the stall to provide a secure mounting to the door Apply a bead of silicone between the walls and base of the stall e For optimum performance you should install the shower door perfectly level on a level surface Failure to do so will lead to water leakage and potential property damage e When installing use heavy duty gloves e FOR THE MATTE GLASS MODELS Oil secretions from skin will leave transparent spots on the matte side of the glass Vigo recommends using gloves during installation You can use a degreasing non abrasive cleaner to remove these secretions The same will happen if you get silicone on the matte glass Use a silicone remover to remove these stains IMPORTANT THE CLEAR GLASS MODEL HAS A REVERSIBLE DOOR AND CAN BE INSTALL
17. l strip 1pc 1pc is extra 15 Door bottom seal strip 1pc 1pc is extra 16 Hex screw 1 1 8 4pc 17 Hex screw 1 5 8 8pc 16 18 Phillips screw 3 4 8pc 19 Plastic anchor green 12pc 20 Plastic anchor white 8pc 21 Hex screw cover 24pc 22 Clear PVC shim 1pack 23 Allen key pack 1 pack OO Y 00 ROM 12 GLASS THICKNESS 3 8 NOTE INSTALLATION MUST BE DONE BY A QUALIFIED LICENSED PLUMBER MODEL VG06061 VIGD 1 WALL CONNECTOR 98001 E 2 STRUCTURAL ARM 98002 36 98002 38 98002 40 98002 42 3 SUPPORT ASSEMBLY ID 98003 Se 4 SIDE GLASS PANEL 97001 36 97001 38 97001 40 97001 42 5 SIDE GLASS PANEL 97006 36 97006 38 97006 40 97006 42 6 SIDE SEAL STRIP 7 GLASS SUPPORT 8 HINGE ASSEMBLY 9 BOTTOM RAIL 3pc 10 DOOR MAGNETIC 96001 22008 98015 95001 36 SEAL STRIP p 95001 38 96002 95001 40 11 BOTTOM CORNER 12 DOOR HANDLE 13 DOOR 14 THROUGH 15 DOOR BOTTOM JOINT ASSEMBLY o HINGE 96016 SEAL STRIP 94001 97007 24 DOOR SIDE 96004 OO DE SEAL STRIP SS O yo O 16 HEX SCREW 1 1 8 98035 Y S S Oy 17 HEX SCREW 1 5 8 98039 18 PHILLIPS SCREW 3 4 98033 19 PLASTIC ANCHOR 98037 A 20 PLASTIC ANCHOR 98038 C 21 HEX SCREW COVER o 96040 22 CLEAR PVC SHIM MISC LU 23 ALLEN KEY PACK MISC MODEL VG06061 VIGD G
18. ou tighten Be sure to use washers on both sides of the panel Place the side glass panel into the bottom rail 49 Use the level to position the side glass panel correctly Making sure the seal strip is against the wall Mark holes on the wall for the mounting screws Remove the side glass panel Drill holes into respective marks and insert plastic anchors 20 inside them Not necessary if installing into studs Studs are the preferred means of installation anchors can pull out of the wall causing property damage and bodily harm Replace the front glass panel back onto the bottom rail and screw it to the wall with 1 5 8 screws 17 GASKETS MAKE SURE TO a WALL LEAVE A GAP OF 3 8 10MM FROM A THE BOTTOM OF THE GLASS HEX SCREW 17 HEX SCREW SIDE GLASS PANEL 5 GASKET VIEW FROM THE TOP FIG 10 12 MODEL VG06061 INSTALLING THE SIDE amp FRONT PANEL SUPPORT o Install the support assembly 3 onto the side glass panel 4 approximately two thirds away from the wall Use hex key to tighten to screws SEE FIG 11 Install the support assembly to the structural arm 42 and wall connector 41 Make sure it s level Mark the holes on the wall for the mounting screws for the wall connector Remove the support assembly Drill holes into respective marks and put plastic anchors 19 in them h Not necessary if installing into studs Replace wall connector to proper position Scr
19. this warranty EXCEPT AS OTHERWISE PROVIDED ABOVE VIGO MAKES NO WARRANTIES EXPRESSED OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE OR COMPLIANCE WITH ANY CODE In any case VIGO cannot be held liable for any amount over and above the purchase price paid for the Product by the owner end user contractor or builder Commercial Limitations In addition to the above conditions and limitations the warranty period for products installed for commercial applications or used in commercial ventures is one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer VIGO is not responsible for loss of use or profit under any circumstances lf the product is used as a display the warranty period begins when the product is placed on display This warranty gives the owner end user specific legal rights The owner end user may also have other rights which can vary from one state or province to another Warranty Service In order to obtain service provided under this warranty during regular business hours contact the dealer or distributor who sold the unit or contact VIGO directly VIGO will provide the warranty service described above when the following conditions have been met the failure is of the nature or type covered by the warranty the user has informed an authorized VIGO Agent or VIGO s warranty service department representative of the nature of the problem
Download Pdf Manuals
Related Search