American Standard 7005.801.295 Installation Guide
Contents
1. firmly to release from lt i ADAPTER 3 5 64 HEX DO NOT DO NOT CLEAN THE WRENCH 6 amp amp PRODUCT WITH SOAPS ACID Pull HANDLE BASE 6 off DECK ADAPTER 2 POLISH ABRASIVES HARSH Remove SPRING CLIP 4 Lift STOP WASHER 5 CLEANERS OR A CLOTH WITH turn 90 and replace Replace SPRING CLIP 4 A COARSE SURFACE Re install HANDLE ASSEMBLY If sory drips operate handles several times from OFF to ON position Do not force handles turn only 90 M968634 Rev 1 2 Speed Connect Drain Troubleshooting Guide If sink does not hold water even oe Stopper is in the down position e Follow CABLE ADJUSTMENT PROCEDURE If Stopper does not raise up fully or sink drains too slowly e Follow CABLE ADJUSTMENT PROCEDURE If you need to remove the TPDC e Follow STOPPER REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting it out of the drain e Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the Stopper should be in the UP position Fig B C Push DOWN on the Lift Knob to make sure it is f2. Amirim Standard Installation Instructions COPELAND 7005 801 Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain a feature found only on American Standard faucets Certified to comply with ANSI A112 18 1 e M968634 Rev 1 2 Speed Connect Drain e Fewer parts installs in less time Never needs adjustment e Guaranteed to seal properly the first time every time Your new American Standard faucet is designed to work only with the Speed Connect drain To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended tools A _ GT Screwdriver Channel Locks Adjustable Wrench Tubing Cutter INSTALL SPOUT NUT nnn before beginning E Insert SPOUT 1 CABLE CONNECTOR 2 and HOSES 3 through center hole making sure the SEAL WASHER 4 is properly seated in spout base Assemble RUBBER WASHER 5 BRASS WASHER 6 and threaded LOCKNUT 7 onto SHANK 8 from underside of sink or mounting surface Hand tighten LOCKNUT 7 Use a screwdriver to tighten SCREWS 7a on LOCKNUT 7 Work your way around LOCKNUT 7 tightening the SCREWS 7a slightly each time until all are snug to ensure even pressure SPOUT BASE INSTALL VALVE BODIES Place RUBBER RING 9 into ADAPTER 10 Install LOCKNUT 11 and RUBBER WASHER 12 onto VALVE BODY 13 From under side of m
3. IPE THREAD RISERS 7 COMPRESSION NUT FLEXIBLE SUPPLIES 3 8 COMPRESSION CONNECTION M968634 Rev 1 2 INSTALL HANDLES Push ADAPTER 1 on VALVE STEM 2 so that the hole of the ADAPTER 1 without a spline is facing up Fig A Tighten STEM SCREW 3 to secure ADAPTER 1 Align HANDLE BASE 4 and push onto DECK ADAPTER 5 until flush against mounting surface Find correct position of LEVER HANDLE 6 by adjusting male teeth on ADAPTER 1 to female teeth in HANDLE 6 Tighten SET SCREW 7 with HEX WRENCH 8 SUPPLIED TEST INSTALLED FITTING With HANDLES 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks m Remove AERATOR 3 Operate both HANDLES 1 to flush water lines thoroughly Replace AERATOR 3 1 2 CHECK DRAIN CONNECTIONS E Operate POP UP KNOB 5 and fill Sink with water Check that DRAIN STOPPER 4 makes a good seal and retains i water in Sink If STOPPER 4 does not seal properly please i WASTE refer to Troubleshooting Guide in these instructions OUTLET VAVAVAVAVAVAVAVAVAVAVAVAVAVAVAUA0A0 E Release POP UP KNOB 5 down and check all drain connections and P trap for leaks Tighten if necessary 1 3 CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT Turn valve to OFF position CLEAN WITH CLEAR WATER DRY k WITH A SOFT COTTON FLANNEL Remove SET SCREW 7 with 5 64 Hex Wrench CLOTH Pull HANDLE 1 UP
4. NGE in SINK to ensure that WHITE FOAM GASKET 3 is fully compressed and not visible Fig A m POP UP KNOB 4 must be fully down Fig B NOT VISIBLE z Sak WHITE FOAM M968634 Rev 1 2 7 ATTACH CABLE CONNECTOR m Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig A Your new POP UP DRAIN installation is now complete Fig B Note Tailpeice on pop up drain is 1 1 4 0 D Fig B CHECK OPERATION OF POP UP Operate LIFT KNOB 1 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions 9 MAKE WATER SUPPLY AND WASTE CONNECTIONS NOTE FLEXIBLE SUPPLIES OR BULL NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY Thread HOSE CONNECTOR 1 with Red Stripe to Hot VALVE INLET 2 Thread HOSE CONNECTOR 1a with Blue Stripe to Cold VALVE INLET 2a Connect water supply to VALVE BODIES 3 3a with 1 2 IPS FLEXIBLE SUPPLIES 4 or 3 8 0 D BULL NOSE RISERS 5 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when bending Use tubing cutter to cut to proper length Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant appropriate connectors and COUPLING NUTS Connect 1 1 4 O D tailpiece on POP UP DRAIN to waste outlet 3 8 O D BULL NOSE 1 2 P
5. fully inserted Fig J Re install the Cam Cap making sure the guide teeth are facing outward If the Cam Cap does not snap into place then rotate the Cam to make sure It is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Troubling Shooting Guide to complete installation Stopper will be Locked Mode in Locked mode and not be removable Vandal Proof Unlocked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig H To install the stopper in Unlocked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig H Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J ___Loop Towarp Re install the Cam Cap making sure the guide teeth are facing ee outward If the Cam Cap does not snap into place then rotate the Cam to make sure It is fully inserted Fig K DRAIN Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Troublingshooting Guide to complete installation Stopper will be Unlocked Mode in Unlocked mode and removable INSTALL CAM CAP M968634 Rev 1 2
6. ounting surface install VALVE BODY 13 through valve mounting holes Threads of VALVE BODY 13 should extent at least 5 16 of a inch above mounting surface top Fig B Thread ADAPTER 10 onto VALVE BODY 13 until snug against internal stop If necessary adjust LOCKNUT 11 Align as shown Tighten LOCKNUT 41 with WRENCH 14 supplied to secure VALVE BODY 13 Repeat above steps for opposite VALVE BODY 13a 10 z rr 5 16 MIN i MOUNTING L SURFACE Do 2AE Kr 11 2 POP UP DRAIN m Remove CLEAR PLASTIC COVER 1 m Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 E Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B lin 6 zzz AK Me H 3 REMOVE FLANGE E Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A E Thread LOCKNUT 3 clockwise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM BELOW FIXTURE Tighten LOCKNUT 1 firmly with Adjustable Wrench or Channel Locks From under side of SINK install DRAIN BODY 1 up through drain outlet Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the SINK Install FOAM GASKET 3 and FLANGE 4 onto drain body from above SINK and tighten FLANGE 4 firmly FLANGE GASKET AND POP UP KNOB Check DRAIN FLA
7. ully down Fig C Re attach the Cable to the Drain Body Connection 2 by threading the Cable Connector 1 clockwise onto the Drain Body Connection 2 and hand tighten Fig A Fig B j Fig C STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration Fig B Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain Fig D Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal Fig E The Stopper can now be removed by lifting it out of the Drain Fig F REMOVE CAM CAP M968634 Rev 1 2 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways Locked Mode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G To install the stopper in Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig G Re install the Cam into the Drain rotating the Cam if necessary to make sure it is
Download Pdf Manuals
Related Search