eLEDing EE814WDC Use and Care Manual
Contents
1. Security amp Safety Lights white CCTV illuminator l re w if a Specifications Detecting Range 180 up to 70 x70 L15 M 35 H 70 Operation Temp 4 F to 125 F Weatherproof IP54 EE815WDC MBP fa z 2 Solar Powered Ultra Bright 5W CREE LED eMitter Self Contained Flood Spot F Building Security amp Safety Lights white CCTV illuminator Specifications Coverage Up to 160 x 120 angle Detecting Range 160 up to 45 x45 L 10 M 25 H 45 Light Head 4W Single super bright LED CREE USA Energy Storage 15WH Li Poly battery Solar Panel L2VDC 4W Mono crystalline self contained Smart Mode A for 6 60 hrs continuous B for 60 hrs Weight 2 2 LBs Light Body Black White light fixture Operation Temp 4 F to 125 F Weatherproof IP54 Peak Bright 60W Halogen Lamp 600Lm 3M 5M color Complies with FCC Part 15 Class B and ICES 003 2004 eStreet amp ePower EE8 amp 10 30W SCLH EE810 30W SSLH EE810W SPZ DENEN AUN ebb EE810 30W SRLH EE840 60W SPG Contact Info 877 579 3889 info eesgi com www eesgi com Rev EE814WDC 052015 Page 42. Then secure the light body unit in place by firmly pushing the light body in toward the mounting base where it locks in position Fig 1 4 amp 1 5 5 With the light body firmly secured in it s mounting position the Pan amp Tilt adjustment features can be used to adjust the direction of the motion detector and the light head directions for optimal performance and coverage The direction and angle of the motion detector can be adjusted Fig 1 6 The LED light head can also be adjusted horizontally 180 forward and backward 120 Fig 1 7 Mounting and Connecting the Solar Panel 1 The solar panel must be mounted in a non obstructed position where it will receive an average of at least 4 hours daily of direct sunlight all year round It should be mounted with a tilt of 35 80 degrees Fig 1 8 A sturdy mounting location such as a wall roof on top of patio under the eaves secure pole or floor ground base This is required to make sure the solar panel is fastened down properly for all weather conditions 2 For Northern hemisphere installations the solar panel should be mounted with a Southerly facing position and visa versa for Southern hemisphere installation the solar panel should face to the North Australia South Africa South America e g 3 Attach the hardware mounting bracket to the solar panel Determine what length of the 10 connecting wire cord is needed to reach the position of the light body and then tie the unused cord be
3. This option converts the light to provide continuous adjustable up to full brightness level illumination for up to 8HRS or plus It can be used as a wall washing light to project lighting on signs flags and areas that need spot lighting Set the main switch to position A Then make sure to adjust the Left Dial from M or all the way to the max H position as desired and adjust the Right Dial Sensitivity to the lower L position refer Fig 2 8 Table Light Conversion using optional Table Stand accessory EE836DTS Fig 5 This option converts the light to a portable table light for camping picnics reading studying and other indoor or outdoor activities Use as a Table Light during low ambient light level conditions Move main switch to position B then make sure to adjust Left Dial Dimming for desired reading light level L M and adjust the Right Dial Sensitivity for max H level 9 An optional AC DC digital power adapter EE DPS 0 8A Fig 5 can be used as a quick charger Also with this adapter it can be used in all profiles and modes as a standard AC DC powered motion sensing flood light with battery back up capability for indoor outdoor security safety lighting applications It can be wall or table mounted or used as a standard portable table light Fig 5 Using this option it can be used in any of the three profiles 10 Avoid placing objects in front of the motion detector that may affect detecting performance Avoid installing th
4. connection This warranty does not cover accessories bulbs batteries accidents alterations unauthorized use or repair neglect misuse abuse damages or defects resulting from normal wear and tear including chips fading scratches abrasions or discoloration due to usage or sun exposure or failure to follow instructions for care and maintenance fire flood and Acts of God This warranty does not include liability for incidental or consequential damages EESGI is not responsible for any damages in excess of the retail purchase price of the product under any circumstances The consumer is responsible for the installation of removal of and reinstallation of the product Customer Service 877 579 3889 M F 10am 5pm PDT www eesgi com Rev EE814WDC 052015 Page 3 Introduction and Intellectual Property Rights Statement Thank you for purchasing the eLEDing LED Smart Solar Lights With its effortless setup and lightweight design the eLEDing LED Smart Light conforms to all your lighting needs It was designed and made to provide many years of trouble free service using environmentally friendly Solar Hybrid Lithium based energy technologies Covered under multiple US European China and other international patents granted and pending worldwide All rights reserved Introduction eLEDing Technology Related Green Systems EE8 amp 18WDC BP WW Solar Powered Ultra Bright 8W CREE LED eMitter Flood Spot Building Parking Lot and Street
5. sensing light In this SMART AUTO mode it will light up to full brightness when motion is detected l When the Left Dial is set at the AUTO position the illumination time has a fixed 60 second delay time for the light to be ON after motion is detected and the lighting will be extended as long as motion is continually detected It will not turn off until the motion detection has stopped and after the illuminating Delay Time has expired The motion Sensitivity Range can be adjusted using the Right Dial Ref Fig 2 page 1 to set the desired Sensitivity Range for the application This adjustment has a motion sensing range from Low 10 Med 35 High 60 For most applications set the dial to between M H in warmer temperature environmental locations set this slightly higher Cautions 1 Adjust the Sensitivity Range so that it is not set too sensitive this will increase false activations and reduce stored battery energy 2 If the PM feature detects that the battery does not have enough stored energy to operate at full brightness when set with the left dial in the SMART AUTO position then it will automatically reduce the light level to half brightness in order to maintain a level of safe lighting until it again receives enough sunlight in good weather conditions to restore it back to normal status In SMART A or B profiles switch position set to A or B position the solar light operates as a true Dusk to Dawn light The unit senses its surrou
6. your new eLEDing light for your applications the unit comes with a initial Set up Walk Test mode to ensure proper installation and performance is optimized To activate this mode move the main switch from OFF to B position as SMART B profile This test mode can be reactivated at anytime night or day to adjust your settings for your application by sliding the switch to OFF then to B position and then making your dial settings 2 When the main switch is set initially to SWART B profile from the OFF position the Set up Test mode will be active for a period of 10 minutes allowing the user to adjust the light settings This mode will work in day or night time conditions The Motion Sensitivity Range can be adjusted at this time for your application from 10 minimum to 60 maximum also in conjunction with making the correct Dial settings during this time you can also adjust the motion detector and light head using the Pan and Tilt features 3 The Set up Walk Test mode is active as long as motion is detected and it will automatically disable itself if 10 minutes has passed without motion being detected During this test period the Red LED indicator will flash through the motion detection lens ball providing visual motion sensing reference as a confirmation of motion detection adjustments When a period of 10 minutes passes without motion detection the unit will automatically switch to normal operation mode It will stop illumination if the set up test was mad
7. e during daylight conditions and it will start illuminating again once it senses a change to darkness from daylight ambient light conditions 4 After the initial Set up Walk Test is complete the main switch may either be kept in the SWART B profile or moved to the SMART A profile for Dusk to Dawn security and safety lighting For most applications SMART B position is the recommended mode providing both Security and Safety lighting 5 Note The Red LED indicator light inside the ball head flashes for the following reasons 1 To indicate motion activity during the 10 minutes initial Set up Walk Test 2 To indicate the battery is low when the sensor detects motion during darkness 3 To indicate charging status during normal charging either in sunny partly cloudy and cloudy daytime periods or when the AC DC digital charger optional is being used for charging in any conditions 6 Storage If this unit has been stored over six months before initial operation then the battery may need to be re charged To re charge the battery after storage turn the main switch to OFF connect the battery plug the wire cord from the solar panel into the light and place it in direct sunlight for 1 2 days Or charge for 2 3 hours using only our optional accessory AC DC Digital Switched Power Adapter EE DPS 0 8A The Li Battery will charge in any of the three switch position including OFF 7 Spot Light Projection Lighting as Traditional full bright ON without motion
8. e unit near air conditioners central heaters or high voltage systems Avoid placing the motion detector head towards street traffic or other high movement areas which cause excessive triggers resulting in shorter battery reserve capacity If this situation is unavoidable decrease the sensitivity and delay time to achieve optimal balance Motion detector is more sensitive to motions across the device and less sensitive to motion moving towards or away from it The solar panel should be mounted where maximum sunlight can be collected Typically the solar panel should face south and avoid facing north for Northern Hemisphere only opposite way for Southern Hemisphere with 35 80 tilt up direction Refer to Fig 1 8 It s fine facing to West or East where sunlight can directly charge the panel for at least 4 hours per day on average Use a soft wet cloth to periodically at least once a one year clean the solar panel to avoid the reduction of energy output due to accumulated dust Clean accumulated snow as soon as possible during the winter season 11 Important Note Lowering the Left Dial setting in either A or B profile will extend the battery capacity reserve and provide extended illuminating ability in geographic locations with poor sunlight such as North West and North East of American e g Product Specifications Coverage Up to 180 sensing angle Detecting Range 180 up to 60 x 60 L 10 M 35 H 60 Light Head 4W Sin
9. eLEDin GJ Model EE814WDC User Manual Built with CREE LED smart Solar Light LED Lighting IMPORTANT Read this User Manual Before Installing Included in this package Initial Installation Refer to Fig 1 Connecting the Battery before setting up 1 The battery has been pre charged before shipping and the light is ready for use 2 Make sure the main switch is in the OFF position 3 Open the battery compartment cover on the back of the light and plug the battery into the connector and carefully make sure the plug position is correct then replace the cover Fig 1 1 4 Initially check the LED illuminator and battery by moving the main switch to position A or B it should light up then turn the switch back to OFF for installation Mounting the Light Body 1 The light body must only be mounted in a vertical position and it should be mounted at least 6 to 10 feet above the ground 2 Choose a flat and safe mounting surface Mark the screw positions through the mounting plate screw holes onto the mounting surface Use 2 or 4 hole mount Fig 1 2 amp 1 3 3 For wood vinyl and metal surfaces mount the back plate directly with provided screws Drill clearance holes using a 3 16 masonry bit for surface of concrete brick or stucco Insert the anchors provided with screws then position the mounting plate and screw the fasteners in securely 4 Attach the light body unit to the wall mounting plate by connecting the top hinges
10. gle super bright LED CREE USA Energy Storage 15WH Li poly battery Solar Panel 12VDC 4W Tempered Glass with 10 cable Mode A for 8 80 hrs continuous B for 80 hrs Weight 1 0 LBs Light Body Operation Temp 4 F to 125 F Weatherproof IP54 Peak Bright GOW Halogen Lamp 600Im 5000K color Complies with FCC Part 15 Class B and ICES 003 2004 Note Installation with factory default settings is recommended for most applications Optional Accessories AC DC Power Adapter EE DPS 0 8A Must be switch type digital 12VDC 0 5 1 5A with current limited power supply Fig 5 Table Stand EE836DTS For use as a table light Fig 5 Auxillary Solar panel with 15 extension cable EE SPEC 15F Important Safety Information Please unplug the battery when shipping the light or packing for flight traveling Do not dispose of battery in fire as this may result in an explosion Do not expose the light to fire or intense heat as the battery may explode Do not immerse in water Never look directly into the light or shine it into another person s eyes Follow proper safety tips to prevent injury such as falling from a ladder during installation Consult your local By laws or local safety guidelines for installing the light fixture on a building One Year Limited Warranty EESGI guarantees this product to be free from defects in material amp workmanship for one year This warranty does not apply to damage from misuse or incorrect installation
11. hind the solar panel with the plastic zip tie that is provided Fig 1 9 4 Then mark the screw holes through the mounting bracket and secure the solar panel in position with the provided hardware 5 Firmly plug the solar panel plug into the bottom of the light body The RED LED indicator inside the motion ball will begin making a double flash indicating that charging status is active during a normal sunny partially sunny or cloudy day Fig 1 10 If this does not happen please check that the plug is fully plugged into the light body or if there is a problem with the wire or solar panel vA Connect the battery OR before using Y 2 Screws 4 Screws Tite kar ea cose ceeeeeee Solar Panel Position Fig 1 Installation Steps 10 60 Right Dial 3 Mode Selectable One step Set up Refer Fig 2 PG 2 amp 3 more info 1 SMART B Profile Mode Max bright adjustable This mode is _recommended_and_can be used for most _illumination lighting applications Set the Main Switch to B in the right position Set the Left Dial between L H for the desired Max brightness level up from soft glow illumination once activated by motion M H is recommended Set the Right Dial between L to H M to below H Z j is recommended 2 a S A Figo _ 2 SMART A Profile Mode Dimming bright adjustable i _ ee ae Set the Main Switch to A in the center position Set the Left Dial Main Switch nae between L H for the des
12. ired level of soft glow illumination when L Do EN JR motion is not detected L M is recommended Set the Right Dial aoe I Saal between L to H M to below H is recommended L SOLAR DC power inppt 3 SMART AUTO Profile Mode Motion activated lighting only m O Set the Main Switch to either A or B Set the Left Dial to AUTO in K A the far left position Set the Right Dial between L to H M to below Fig 2 Light Profiles amp Settings H is recommended Rev EE814WDC 052015 Page 1 eLEDing SMART Light user related additional information Our latest generation of software based eLEDing Solar Hybrid powered Light offers three principal SMART operating profile modes The Sensitivity Range of motion length of illuminating time and levels of brightness and dimming are set and controlled with adjustable dials Fig 2 The family of eLEDing solar lights use an exclusive Intelligent Power Management IPM embedded and self compensated feature for managing and optimizing the Lithium based battery either Li Poly or LiFePO4 for a full range of operation This optimizes the battery s life cycle to adapt to most environmental conditions allowing both the battery and light to perform for many years Optimization of SMART Profiles Operation In either A or B position if the Left Dial is set to Auto turned all the way to the far left past L to the Auto position then this light will convert to operate as a traditional motion
13. nding ambient light level and will turn on in darkness providing adjustable moonlight soft glow lighting all night long When motion is detected it lights up to it s full brightness or pre set max brightness within the set sensitivity range For either new installations or replacing existing AC light applications the B position is the recommended SMART profile when used as an outdoor or indoor light for Security and Safety It can also be used to enhance CCTV applications by providing full color white light image illumination for the area of camera coverage without AC DC power source or power shortage limitations Fig 4 Unusual Positions cs In SMART B profile the motion activated brightness level is controlled and set by the user In this mode the Left Dial functions as a Brightness adjusting dial for setting the light level from lowest L to highest H brightness When motion is detected it will brighten up to the level as pre set by the Left Dial and when motion stops it will slowly dim down to the lowest factory fixed pre set moonlight soft glow lighting level It is recommended that for most country locations with good sunshine that this setting should be H and for geographic locations with poor sunshine it should be set at a lower level between M to below H SMART B also allows the brightness level to be adjustable between L to M Set the Right Dial to H when using the light as a portable or table reading studying light for outdoor or indoor u
14. se Fig 5 Caution The higher the brightness level is set to the more stored battery energy is used when activated by motion If the IPM detects that the battery does not have enough capacity to run this mode it will automatically convert to AUTO mode for energy saving and turn on only when motion is detected until it receives enough sunlight to operate the SMART feature correctly In SMART A profile the lower soft glow lighting level is controlled and set by the user The Left Dial is used for setting the dimming level of moonlight soft glow lighting from the level of lowest L to highest H brightness When motion is detected the light will brighten up to the factory fixed max full brightness level and then dim back down to the moonlight level set by the user It is recommended that for most country locations with good sunshine that this setting should be middle level M or less For locations with poor sunshine it should be set at a the lowest level L or switch to SWART B profile is recommended SMART A with the Left Dial set at its highest H the light operates as a projecting spot light In the H position with the battery fully charged the light will be ON at its brightest illumination and it will provide continuous lighting for a time period of up to 8 hrs Caution The higher the minimum soft glow level is set to the more stored battery energy is used to provide soft glow lighting If the IPM detects that the battery does not have enough capaci
15. ty to run this mode it will automatically convert to AUTO mode for energy saving and turn on only when motion is detected until it receives enough sunlight to operate the SWART feature correctly In either SMART A or B profile if user geographic location has outstanding daytime sunlight conditions all year California Arizona New Mexico Florida of USA e g then this SMART light provides a wide range of adjustability in lighting performance Using the SMART A profile you can increase the Moonlight Dusk to Dawn dimming level up to full brightness as peak ON Using the SMART B profile you can increase up to Max brightness on peak when motion is detected For most applications using the SMART B profile with the factory preset Dial settings is recommended In both A and B profile if the IPM detects that the battery does not have enough capacity to operate these modes in critical weather conditions then it will convert to AUTO mode And if the IPM detects that there is insufficient battery reserve to operate in Auto mode then it will automatically disable illuminating functions leaving only the charger active to protect the battery from over discharge causing damage After enough sunlight is received to charge the battery the unit will first return to AUTO mode for motion activated lighting until it receives enough sunlight energy to operate the SMART profiles properly Rev EE814WDC 052015 Page 2 User Tips video reference www eesgi com 1 To set up
Download Pdf Manuals
Related Search