Hampton Bay HB3430-44 Installation Guide
Contents
1. CHAIN PENDANT FIXTURE INSTALLATION INSTRUCTIONS Please read carefully and save these instructions as you may need them at a later date CAUTION Turn off the main power at the circuit breaker before installing the fixture in order to prevent possible shock GENERAL ASSEMBLY AND INSTALLATION Continued Connect the remaining FIXTURE GROUND WIRE 7 to the SUPPLY GROUND WIRE 8 using a WIRE CONNECTOR 13 Place wiring and connections inside the OUTLET BOX 1 See Fig 1 Slide the CANOPY 15 and the THREADED RING 16 up the CHAIN 17 Place the CANOPY 15 over the OUTLET BOX 1 and secure it in place by screwing the THREADED RING 16 onto the SCREW COLLAR LOOP 6 See Fig 1 Screw light bulbs into the lamp sockets and make sure they do not exceed the maximum wattage specified on the fixture s wattage rating label INSTALLATION IS NOW COMPLETED All electrical connections must be in accordance with local and National Electrical Code N E C standards If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions ASSEMBLY AND INSTALLATION Take the parts out of the mounting package and thread both 1 8 IPS HEX NUTS 5 several turns onto each end of the NIPPLE 4 Screw the end of the NIPPLE 42. several turns into the threaded hole of the MOUNTING BRACKET 2 but do not tighten the 1 8 IPS HEX NUTS 5 Pull the SUPPLY WIRES 9 amp 11 and the SUPPLY GROUND WIRE 8 out from the OUTLET BOX 1 and attach the MOUNTING BRACKET 2 assembly to the OUTLET BOX 1 using the slotted holes of the MOUNTING BRACKET 2 and the MOUNTING SCREWS 3 provided See Fig 1 Thread the SCREW COLLAR LOOP 6 onto the bottom end of the NIPPLE 4 Place the CANOPY 15 over the OUTLET BOX 1 and adjust the SCREW COLLAR LOOP 6 and NIPPLE 4 until the midpoint of the outside threads on the SCREW COLLAR LOOP 6 is centered aligned with the surface of the CANOPY 15 Remove the CANOPY 15 and tighten both 1 8 IPS HEX NUTS 5 down on the MOUNTING BRACKET 2 and the SCREW COLLAR LOOP 6 See Fig 1 Screw on the COLUMN 19 to the TOP NIPPLE 20 See Fig 2 Open up the end links of the CHAIN 17 and attach one end of the CHAIN 17 onto the FIXTURE LOOP 18 Slide the THREADED RINR 16 and the CANOPY 15 onto the CHAIN 17 in that order and attach the other end of the CHAIN 17 to the SCREW COLLAR LOOP 6 Close the ends of the chain links See Fig 1 amp 2 Unravel the fixture lead wires and FIXTURE GROUND WIRE 7 and thread them through every other link of the CHAIN 17 starting with the chain link attached to the FIXTURE LOOP 18 Feed the fixture lead wires and FIXTURE GROUND WIRE 7 through the SCREW COLLAR LOOP 6 a
3. nd NIPPLE 4 assembly Pull the fixture lead wire and the FIXTURE GROUND WIRE 7 upward to remove any excess slack See Fig 1 Attach the power supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE 9 to the SMOOTH FIXTURE LEAD WIRE 10 and the WHITE SUPPLY WIRE 11 to the RIBBED FIXTURE LEAD WIRE 12 Loop the FIXTURE GROUND WIRE 7 around the GROUND SCREW 14 of the MOUNTING BRACKET 2 Note Be sure to provide an extra 3 length of the GROUND SCREW 14 6PCS PER ARM A IPCS PE CRYSTAL CHAIN IPCS P CRYSTAL CHAIN SPES SEF OUTLET BOX MOUNTING BRACKET MOUNTING SCREW NIPPLE 1 8 IPS HEX NUT SCREW COLLAR LOOP FIXTURE GROUND WIRE SUPPLY GROUND WIRE 9 BLACK SUPPLY WIRE 10 SMOOTH FIXTURE LEAD WIRE 11 WHITE SUPPLY WIRE 12 RIBBED FIXTURE LEAD WIRE 13 WIRE CONNECTOR 14 GROUND SCREW 15 CANOPY 16 THREADED RING 17 CHAIN 18 FIXTURE LOOP 19 COLUMN 20 TOP NIPPLE
Download Pdf Manuals
Related Search