Casablanca 53195 Installation Guide
Contents
1. Screw two 2 housing assembly screws from the hardware bag halfway into the motor housing It does not matter which two screw holes you choose Feed the wire plug through the center hole of the upper switch housing then wrap keyhole slots around the screws and twist counterclockwise 3 Insert the third screw found in the hardware bag into place and then tighten all three 3 screws Connect the plugs from the upper and Lift the lower switch housing up until the Connect the fandangle to the short chain lower switch housings Make sure to holes line up with the screw holes in the coming from the switch housing line up the colored markings on the upper switch housing Install the three 3 connectors switch housing screws found in the hardware bag 14 d The pull chain controls the To switch the direction of air For cleaning the fan use soft fan high medium low flow move the reverse switch brushes or claths to prevent extra low and off to the opposite position scratching Cleaning products Inwarm weather use may damage the finishes downward air flow pattern In cold weather use upward airflow pattem i5 Fan doesn t work Excessive wobbling Noisy Operation Tighten the blade and blade iron screws until they are snug Pull the pull chain to make sure Tighten all of the blade and itis on blade iron2. Congratulations on purchasing your new Casablanca ceiling fan Itwill provide comfort and performance in your home or office for many years This installation and operation manual contains complete instructions for installing and operating your fan We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the word To register your fan please visit www CasablancaFanCo com register What to Expect with Your Installation Bi Mounting Options Ceiling Bracket installation Preparation Maintenance amp Cleaning Must be able to secure the fan to 7 Baling structure or fan rated outlet box If you are unfamiliar with wiring use a qualified electrician E iow your wing 30 inches from blade ipto nearest wall or obstruction 7feet From bottom edge of blade tothe floor E Assess locaton You may need a friend to help you Check box to see fan weight D Ceiling angles greater than 34 will require an Angled Mounting Kit See page 4 for details EZ assess cating angle Standard Downrod for ceilings 8 10 feet high Shorter Downrod for fans installed close to ceiling EJ Longer Downrod for ceilings 10 feet or higher 7 selects downrod length 6 uM E we st
3. e a wire connector over them then twist clockwise until tight Using orange wire connectors from the Jk hardware bag connect the black wire ungrounded from the ceiling to the black and the blue wires from the fan Connect the white wire grounded from the ceiling to the white wire from the fan Using an orange wire connector from the we hardware bag connect the 3 grounding wires green green yellow stripe or bare copper coming from the ceiling downrod and hanging bracket 10 Poston thecanopy otha when Lftthe canopy into placesothat sert the twa canopy crews te into place the canopy ts crew holes are aligned found in the hardware bag the hanging bracket as show Remember the screws that you kept after removing the shipping blocks page 6 You need them plus five more from hardware bag for this step gy Isertarommets found in the B hardware Lohtly attach the blade irons to the bag into the holes in the blades then motor with screws found in secure each blade to a blade iron with the X hardware bag then securely screws found in the A hardware bag tighten after both screws are attached Your blades are shielded with Dust Armor which is a nanotechnology coating that repels dust For JJ leaning the fan use soft brushes or cloths to prevent scratching Cleaning agents may damage the finishes 12
4. ripper 7 screwarivers Ts Power Drill 9 64 Drill Bit optiona optional Mf mounting to a support structure you will also need these tools 3 AINN agii If you have a flat ceiling Hang your fan by a standard downrod included Standard Mounting LNOILdO m En 2 you have an angled ceiling 1 You will need a longer downrod sold separately 2 lfyourceling angle is greater than 34 you will also need an Angled Mounting Kit sold separately Ceiling Outlet Box required Mounting Outer Box Style gt required Nodes Use the three steps below to determine if your ceiling angl is greater than 34 M 7 iE ka Guide Touches Guide Touches Wall Use Standard Mounting Use Angled Mounting s Ceiling amp Wall butNOT Ceiling or Low Profile Mounting to hang the fan from a Youreed ONLY a You need BOTH to hang the fan from a fat ceiling vaulted or angled ceiling E a Longer O a Longer D LS en E N en Angled Dot comms eg 5 ip E AA For angled ceilings point opening toward peak Usewood screws Use machine screws Make sure all four 4 bumpers includled when securing provided with outlet Ifyou are unable to do this are still attached tesupportstructure with box when securing to call Technical Support at approved electrical outle
5. screws until they Push the motor reversing switch ki firmly leftor right to ensure that Turn the power off support itis engaged the fan carefully and check that the hanger ball is properly seated Check to see if any of the blades are cracked f so replace all ofthe blades Check the circuit breaker to ensure the power is turned on Use the provided balancing Make sure the blades spin freely kit and instructions to balance the fan Turn off power from the circuit breaker then loosen the canopy and check all the connections according to the wiring diagram on page 10 Check the plug connection in the switch housing AUTHORIZED SERVICE CENTERS For the most updated listing of Casablanca Authorized Service Centers visit www CasablancaFanCo com or call toll free 1 888 227 2178 16
6. t existing ceiling fan rated 1 888 227 2178 bax Dri 9 64 plotholes outlet bax Make sure insupportstructuretoaid it is securely installed in securing ceiling bracket and is acceptable for fan with hardwarefoundin support of 31 8 kg 70 Ibs the e hardware bag or less Remove the shipping blocks from the motor Save the five screws They will be needed for blade iron installation Time Saver Tip Geta helper to insert grommets found in the Ill hardware bag into the blades while you re doing the next couple of steps Standard Downrod for ceilings 8 10 high Option 1 Downrod for fans installed close to celling L Option 2 ceilings 10 or higher Sold Separately Steps 6 10 to reassemble with new pipe Remove the pre installed Hand tighten the dawnrad at setscrew so that the dawnrod least 4 5 full turs until it stops The wires can be cut but leave at least 8 extending from the top of the downrod Tighten the setscrew with pliers DO NOT HAND TIGHTEN 3 8 Put the wires and downrod through the DO NOT PICK THE FAN UP BY THE canopy Let the canopy sit loosely on top CANOPY OR WIRES Place the downrod of the fan ball into the slot in the ceiling bracket Note To connect the wires hold the bare metal leads together and plac
Download Pdf Manuals
Related Search