TroposAir 88459 Instructions / Assembly
Contents
1. f i v 4ME42 LK This instruction contains 6 pages Page 1 Foreword Page 2 Unpack and inspect parts contained Page 3 Notes before installation and Hanging system installation Page 4 Wire connection Page 5 Canopy installation Blade installation Light kit installation Page 6 Pull chain knob installation Ul Net weight i 5 1 KGS Toll Free 1 855 676 7247 ies Eee WARNING Read and follow these instructions carefully and be mindful of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 1 To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning Two people recommended for fan installation 2 To avoid possible electric shock be sure electricity is turned off at the main power box before wiring i All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections 3 Make sure that your installation site will not allow rotating fan blades to come in contact with any ww object Blades should2. side screw Removing Loosening Attach blade to blade holder with 3 blade screws and 3 paper washers provided from hardware bag Make sure all screws are firmly tightened 2 Secure Blade Assembly to the motor with 2 motor screws provided from hardware bag NOTE To prevent wobble do not bend blade or blade holder s T 4 Blade Screw 3 v lt Pap er Washer 3 Blade Assembly Fan Assembly 5 LIGHT KIT INSTALLATION Install bulbs to lamp holders on light fixture 2 Attach amp rotate glass shade clockwise to light kit pan Fan Assembly G9 Halogen bulb 2 25W x 2 included P9 6 PULL CHAIN KNOB INSTALLATION Connect Pull Chain Knobs provided from hardware bag to the pull chain from switch housing as shown below Pull Chain Knob g 7 Turn on the power your fan is ready for operation Note 1 Fan s pull chain switch cycles through Off High Medium and Low speeds Note 2 Do not use reverse switch while blades are in motion to prevent injury and damage to motor P6
3. be at least 7 feet from floor when fan is in operation 4 If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight of the moving fan Ifthe fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel 5 Blades should be attached after motor housing is hung and in place Fan motor housing should be keptin carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets 6 After making electrical connections spliced conductors should be turned upward and pushed carefully up into outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and the HOT wires on the other side 7 Electrical diagrams are for reference only Light kits that are not packed with the fan must be UL listed and should be installed per the light kit s installation instructions 8 After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury 9 The fan can be made to work immediately after inst
4. acket onto fan assembly firmly Note This will permit you to make the wire connections without having to hold the fan up as well TL 3 gt eo i Mounting Bracket Canopy decorating cap Fan assembly 2 WIRE CONNECTION Making electrical wire connection Follow diagram below and make sure that all exposed wires are secured inside wire nuts or terminal block Note Wires from house may vary in color and may not include ground wire green White wire from house to white wire from fan Black wire from house to black wire and blue wire from fan Ground wire from house to green wire from downrod and from mounting bracket Secure with twist lock wire nuts Included After wiring is completed gently push wires into junction box with wire nuts pointing upward From House From Fan White White AC N MOTOR N Black AC L 13 Blue For Light Kit TRANH from down Green for ground wire Secure with twist lock wire nuts P4 3 CANOPY INSTALLATION Note Four screws are pre screwed on mounting bracket for canopy installation Remove left hand side screw on mounting bracket first and loosen the other one Note Please do the same for the other two screws on the across side of mounting bracket 2 Rotate the canopy slightly until both two loosening screws are in the holes of L type slots G Tighten 4 screws firmly 2 L Type Slots Screw 4 Tightening Left hand
5. allation The bearings are adequately charged with grease so that under normal conditions further lubrication should not be necessary 10 This fan is suitable for indoor location use 11 This fan is reversible P1 Unpack and inspect fan carefully to be certain all contents are included Hardware Bag For Mounting Plate Flat Washer x2 Spring Washer x2 OS Machine Screw x2 X Wood Screw x2 IS Canopy set screw x3 For Wire Connection Wire Nutx 3 l l Donarai j For Blade Installation Paper Washer x 13 one spare washer included O Oo O O O CGO Oo CG CG OC OG Blade Screw x 13 one spare screw included FFF EE T m PPPPPP Motor Screw x 9 one spare screw included O O O O O Canopy ______ gt Canopy Decorating Cap For Fan Pull Chain Knob x2 For Blade Balance Balanced slide x 1 A Weight block 3G x 3 POD Fan Assembly Light Kit Fitter Blad e 4 G9 Halogen bulb 2 gt p lt Decor chip 4 Glass P2 WARNING blades should be at least 7 feet from floor Note 1 Note 2 Turn off power at breaker Use metal outlet box suitable box to avoid possible for fan support electrical shock Outlet box must support 35 Ibs min 1 HANGING SYSTEM INSTALLATION 1A Installing mounting bracket to ceiling outlet box Install mounting bracket to outlet box in ceiling by using screws included with the outlet box and washers fr
6. om the hardware bag Outlet Box gt Mounting 4 Bracket 1B This fan has two installation methods available Downrod mount Standard Please follow up Step 1C and 1D 2 Flush mount Hugger Please directly go to Step 1E and 1F Downrod mount 2 Flush mount See Step 1C and 1D See Step 1E and 1F ZZ 1C Installing Downrod and Yoke Remove cross pin and cotter pin from downrod 2 Insert downrod through canopy and feed motor lead wires through downrod Loosen 2 downrod jam screws at yoke Insert downrod assembly into yoke 4 Insert the cross pin through yoke amp downrod and secure with cotter pin Tighten both downrod jam screws to further secure downrod f f ly 5 Ji fy Hf ie y Hf AX f k at Tei l a tlt A IWAN Cm gt ht JA SA V E BONER Cross Pin Cotter Pin ge 1 comm J o Downrod Jam ugi Screw 2 Loosening Ajquessy lt pojumoq Set Screw 2 gt Tightening o 1D Hanging the fan For Downrod mount Lift fan assembly onto mounting bracket Rotate fan so that the groove on the ball engages the ridge in the mounting bracket Mounting eo Bracket Mounting Bracket 1E Canopy Assembly For Flush mount 1F Hanging the fan For Flush mount Remove canopy decorating cap from bottom of canopy Lift the fan assembly and hang onto the tab on 2 Fasten 3 canopy set screws provided from hardware bag mounting br
Download Pdf Manuals
Related Search