none YG268-BN Instructions / Assembly
Contents
1. Secure the outlet box MM not included directly to the building structure Use appropriate fasteners and materials not included The outlet box and its bracing must be able to fully support the weight of the moving fan at least 35 Ibs Do not use a plastic outlet box The illustrations below show three different ways to mount the outlet box MM not included MM N N a N MM To hang your fan where there is an existing fixture but no ceiling joist you may need an installation hanger bar NN not included as shown above Assembly Standard Ceiling Mounting 1 Preparing the canopy Remove the two non slotted mounting bracket screws BB from the canopy B and loosen the slotted mounting bracket screws BB on the canopy B Remove the canopy B from the mounting bracket A by turning the canopy B counterclockwise 3 Assembling the fan WARNING Failure to properly install the cotter pin FF could result in the fan becoming loose and possibly falling NOTE If a longer downrod is needed not included take out the screw located in the hanger ball lower the hanger A ball and remove the pin Remove all three pieces from the downrod and assemble them onto the new longer downrod before proceeding step 3 Route the wires through the canopy B and then through the hanger ball downrod assembly D Align t2. approximately 9 in Once you have decided which ceiling installation you will use refer to the corresponding sections and procedures during the assembly period Where necessary each section of the instructions will note the different procedures to follow for the two types of installation Standard Ceiling Mounting Close to Ceiling Mounting HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Installation MOUNTING OPTIONS WARNING To reduce the risk of fire electric shock or personal injury mount the fan to an outlet box marked acceptable for fan support using the screws provided with the AN outlet box An outlet box commonly used for the support of lighting fixtures may not be acceptable for fan support and may need to be replaced If in doubt consult a qualified NOTE You may need a longer downrod to maintain proper blade clearance when installing on a steep sloped ceiling A The maximum angle allowable is 18 away from horizontal If the canopy B touches the hanger ball downrod assembly D then remove the decorative canopy bottom cover C and turn the canopy B 180 before attaching the canopy B to electrician the mounting bracket A If your ceiling fan does not have an existing UL listed mounting box then install one using the following instructions NN Disconnect the power by removing the fuses or turning off the circuit breakers
3. as may otherwise be accorded by law Some states do not allow the exclusion of incidental or consequential damages so the above exclusion or limitation may not apply to you This warranty gives specific legal rights and you may also have other rights which vary from state to state This warranty supersedes all prior warranties Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer Contact the Customer Service Team at 1 877 527 0313 or visit www homedepot com Pre Installation SPECIFICATIONS Fan size Speed Volts Amps Watts RPM CFM N W G W C F pr LI m 0 24 14 75 1803 7 61 kg 8 75 kg ee Medium 0 34 27 114 2860 16 74 Ib 19 25 Ib High 0 48 58 174 4469 NOTE These are approximate measures They do not UL include amps and wattage used by the light kit a LISTED TOOLS REQUIRED DP Phillips Flat blade Step Wire Electrical AT screwdriver K screwdriver ladder stripper Tape Pre Installation continued HARDWARE INCLUDED A NOTE Hardware shown to actual size unless noted otherwise in the table below FF O HiL BB EA E E GG E HH F DD E ll EE JJ Part Description Quantity AA Plastic wire nut not to scale 3 Mounting bracket screw preassembled Blade attachment screw and fiber washer Blade arm screw and lock washer Clevis pin preassembled Cotter p
4. Item 549 510 Model YG268 BN USE AND CARE GUIDE BROOKHURST 52 INCH CEILING FAN Questions problems missing parts Before returning to the store call Home Depot Customer Service 8 a m 6 p m EST Monday Friday 1 877 527 0313 HOMEDEPOT COM THANK YOU We appreciate the trust and confidence you have placed in Home Depot through the purchase of this ceiling fan We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Home Depot Table of Contents Table of Contents cccccccsseesesesessseeseseseseeeseessssesesseenenens 2 Safety Information 2 ccceeeeeeeeseeseeeeeeeeeeeeeeeeeenseeneees 3 Warranty 0a AA 4 Pre Installatlon AGING 4 SSDOCITICAUOMINS NAAN 4 Tools Required amain 4 Hardware nade uda dau dudu aa 5 Package Contents La aunaamanimabuniabnasunbbiiman 6 Dual Mounting Instructions ccccessseeeeeeeeseeeeseeeeeeeees 7 Installation aa AGA 8 Assembly 711711222202023 REAN NAGA 9 Standard Ceiling MOUNTING u uumumuukubaukumauwuwausuwausawsuwawauwausuwawas 9 Close to Ceiling MOUNTING u uuumkmamunanwuwanawausawsuwawsuwausasunan 10 Hanging the Pana aa 11 Attaching the Fan Blades u uuummumumambunawauwawauwawauwawsuwausawausawaunan 14 Installing the Light Kit uumuummmkkunaunuwaasuwaasawausawsunasunansunaana 16 Operation aNG NANANG 17 Pull Chain Operating Inst
5. ct 1 877 527 0313 for further assistance Service Parts A luv Part Description Mounting bracket preassembled Canopy Canopy bottom cover preassembled Hanger ball downrod assembly Fan motor assembly Blade Blade arm Light kit I onim oloo D gt Glass shade AA To EF BB B II F g T CC F DD G BE H FF Fes Part Description AA Plastic wire nut BB Mounting bracket screw preassembled CC Blade attachment screw and fiber washer DD Blade arm screw and lock washer preassembled EE Clevis pin preassembled FF Cotter pin preassembled GG Collar setscrew preassembled HH Collar mounting screw with lock washer preassembled ll Light kit mounting screw preassembled JJ Light holder thumbscrew preassembled KK 13 watt compact fluorescent bulb LL Pull chain and fob Questions problems missing parts Before returning to the store call Home Depot Customer Service 8 a m 6 p m EST Monday Friday 1 877 527 0313 HOMEDEPOT COM Retain this manual for future use YG268000001 A
6. ctor on one side of the outlet box and the ungrounded conductor on the other side of the outlet box 9 All setscrews must be checked and retightened where necessary before installation not use this fan with any solid state fan speed control device WARNING To reduce the risk of electrical shock or fire do It will permanently damage the electronic circuitry WARNING To reduce the risk of personal injury do not bend the blade arms also referred to as flanges when installing the brackets balancing the blades or cleaning the fan WARNING Do not insert foreign objects between rotating fan blades WARNING To reduce the risk of fire electric shock or personal injury mount the fan to the outlet box marked acceptable for fan support with the screws provided with the outlet box CAUTION To reduce the risk of personal injury use only the screws provided with the outlet box HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Warranty We warrant the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser We also warrant that all other fan parts excluding any glass or acrylic blades to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the orig
7. f the canopy B are on top and then proceed to place the canopy B over the collar at the top of the fan motor assembly E Align the mounting holes in the bottom of the canopy B with the holes in the top of the fan motor assem bly E and fasten using the three collar mounting screws with lock washers HH previously removed Tighten the collar mounting screws HH securely 10 Preparing the motor Remove three of the six collar mounting screws with lock washers HH every other one from the collar on top of the fan motor assembly E Assembly Hanging the Fan Attaching the fan to the electrical box A WARNING To reduce the risk of fire electric shock or other personal injury mount the fan only to an outlet box or supporting system marked acceptable for fan support and use the mounting screws provided with the outlet box ba Pass the 120 volt supply wires through the center hole in the mounting bracket A Install the mounting bracket A to the outlet box MM with the screws and washers provided with your outlet box When using close to ceiling mounting it is important that the mounting bracket A be level If necessary use leveling washers not included between the mounting bracket A and the outlet box MM Note that the flat side of the mounting bracket A is toward the outlet box MM Securely tighten the two mounting sc
8. ground wire f P AA ON o WARNING To reduce the risk of fire or electric shock do Q KA Dm not use this fan with any solid state speed control device If you feel you do not have enough electrical wiring knowledge or experience have your fan installed by a licensed electrician Follow the steps below to connect the fan to your household wiring Use the plastic wire nuts AA with your fan Secure the plastic wire nuts AA with electrical tape Make sure there are no loose strands or connections Connect the ground conductor CCC of the 120V supply this may be a bare wire or a wire with green colored insulation to the green ground lead s 00 of the fan When using standard ceiling mounting there are two green grounding leads one from the mounting bracket A and one from the hanger ball downrod assembly E When using close to ceiling mounting there is only one green ground lead 00 from the mounting bracket A since the hanger ball downrod assembly E is not used o Connect the fan motor white wire PP to the supply white neutral wire BBB using a plastic wire nut AA Connect the fan motor black wire QQ and the blue wire RR to the supply black hot wire AAA using a plastic wire nut AA Turn the wire nut connections upward spreading them apart so the green ground 00 will be on one side of the outlet box MM and the white PP b
9. he holes at the bottom of the hanger ball downrod assembly D with the holes in the collar on top of the fan motor assembly E Carefully insert the clevis pin EE through the holes in the collar and the hanger ball downrod assembly D Be careful not to jam the clevis pin EE against the wiring inside the hanger ball downrod assembly D Insert the cotter pin FF through the hole near the end of the clevis pin EE until it snaps into the locked position 2 Preparing the motor Remove the clevis pin EE and cotter pin FF and loosen the two collar setscrews GG from the motor collar Tighten the two collar setscrews GG on top of the fan motor assembly E firmly HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Assembly Close to Ceiling Mounting 3 Preparing the canopy Remove the mounting bracket A from the canopy B by loosening the four mounting bracket screws BB on the top of the canopy B Remove the two non slotted mounting bracket screws BB and loosen the slotted mounting bracket screws BB Remove the canopy bottom cover C from the canopy B Assembling the fan AN WARNING Failure to completely tighten the three collar mounting screws HH could result in the fan becoming loose and possibly falling Make sure the slot openings o
10. in preassembled Collar setscrew preassembled Collar mounting screw with lock washer preassembled Light kit mounting screw preassembled Light holder thumbscrew preassembled 13 watt compact fluorescent bulb not to scale Pull chain and fob not to scale HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Pre Installation continued PACKAGE CONTENTS LZ B 7 D D E H Part Description Quantity Part Description Quantity A Mounting bracket preassembled 1 F Blade 5 B Canopy 1 G Blade arm 5 C Canopy bottom cover preassembled 1 H Light kit 1 D Hanger ball downrod assembly 1 l Glass shade 3 E Fan motor assembly 1 Pre Installation continued DUAL MOUNTING INSTRUCTIONS This ceiling fan is supplied with two types of hanging assemblies the standard ceiling installation using the downrod with ball and socket mounting and the close to ceiling mounting The close to ceiling mounting is recommended in rooms with less than 8 ft ceilings or in areas where additional space is desired from the floor to the fan blades When using the standard downrod installation the distance from the ceiling to the bottom of the fan blades will be approximately 12 in The close to ceiling installation reduces the distance from the ceiling to the bottom of the fan blades to
11. inal purchaser We agree to correct such defects without charge or at our option replace with a comparable or superior model if the product is returned To obtain warranty service you must present a copy of the receipt as proof of purchase All costs of removing and reinstalling the product are your responsibility Damage to any part such as by accident misuse improper installa tion or by affixing any accessories is not covered by this warranty Because of varying climatic conditions this warranty does not cover any changes in brass finish including rusting pitting corroding tarnishing or peeling Brass finishes of this type give their longest useful life when protected from varying weather conditions A certain amount of wobble is normal and should not be considered a defect Servicing performed by unauthorized persons shall render the warranty invalid There is no other express warranty We hereby disclaim any and all warranties including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty Some states do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you The retailer shall not be liable for incidental consequential or special damages arising out of or in connection with product use or performance except
12. it 11 Attaching the light kit to the switch housing CAUTION Before starting the installation disconnect the power by turning off the circuit breaker or removing the fuse at the fuse box Turning power off using the fan switch is not sufficient to prevent electric shock Remove the three light kit mounting screws Il from the light kit H and keep these screws While holding the light kit H under your fan motor assembly E locate two single white and blue wires in the switch housing labeled FOR LIGHT Make the polarized plug connections White to white Blue to black Carefully push all wires back into the switch housing Install the light kit H onto the switch housing with the three light kit mounting screws Il provided Be sure to tighten all screws 1 Mounting the glass shades and installing the light bulbs Mount the glass shades I to the light sockets by partially unscrewing the three light holder thumbscrews JJ on each glass holder inserting the glass shades I and gently and evenly tightening the light holder thumbscrews JJ by hand to the glass shades I Do not overtighten Install three 13 watt compact fluorescent bulbs KK included KK 16 Operation PULL CHAIN OPERATING INSTRUCTIONS Install two pull chains and fobs LL onto the pull chains located in the switch housing and light kit H Tur
13. lack QQ and blue wire RR will be on the other side Carefully tuck the connections up into the outlet box MM 12 Assembly Hanging the Fan continued fa Standard ceiling mounting 7b Close to ceiling mounting properly sits in the groove in the hanger ball D before attaching the canopy B to the mounting bracket A by WARNING Make sure the tab on the mounting bracket A turning the canopy B until it drops into place WARNING Locking slots of the canopy B are provided only as an aid to mounting Do not leave the fan assembly unattended until all four canopy screws BB are engaged and firmly tightened only as an aid to mounting Do not leave the fan assembly unattended until all four canopy mounting bracket screws WARNING The locking slots of the canopy B are provided BB are engaged and firmly tightened Slide the canopy B up to the ceiling Make sure you have placed the wires safely into the outlet box MM Secure the canopy B to the mounting bracket A with the four canopy mounting bracket screws and lock washers BB included with your fan Remove the fan from the hook on the mounting bracket A Secure the canopy B to the mounting bracket A with the four canopy mounting bracket screws and lock washers BB provided HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Assembly Attaching
14. n on the power and check the operation of the fan The pull chain controls the fan speed as follows 1 pull High 2 pulls Medium 3 pulls Low and 4 pulls Off Speed settings for warm or cool weather depend on factors such as the room size ceiling height and number of fans To turn the light kit ON or OFF pull the chain that is attached to the light kit H REVERSE SWITCH OPERATING INSTRUCTIONS The reverse switch is located on the surface of the switch housing This switch controls directions forward switch down or reverse switch up NOTE Wait for the fan to stop before reversing the direction of the blade rotation Warm weather Counterclockwise Direction A downward air flow creates a cooling effect This allows you to set your air conditioner on a warmer setting without affecting your comfort Cool weather Clockwise Direction An upward air flow moves warm air off the ceiling This allows you to set your heating unit on a cooler setting without affecting your comfort UNO C C 17 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Care and Cleaning Do Check the support connections brackets and blade attachments twice a year Make sure they are secure Because of the fan s natural movement some connections may become loose over time It is not necessary to remove the fan fr
15. om the ceiling Clean your fan periodically Use only a soft brush or lint free cloth to avoid scratching the finish The plating is sealed with a lacquer to minimize discoloration or tarnishing Optional Apply a light coat of furniture polish to the wood blades Optional Cover small scratches with a light application of shoe polish Do not Use water when cleaning Water could damage the motor or the wood or possibly cause an electrical shock Apply oil to your fan or motor The motor has permanently lubricated sealed ball bearings Troubleshooting WARNING Make sure the power is off at the electrical AN panel box before you attempt any repairs Refer to the section Making the Electrical Connections on page 12 Problem Solution The fan will not start Check the main and branch circuit fuses or breakers Check the line wire connections to the fan and switch wire connections in the switch housing Make sure all motor housing screws are snug Make sure the screws that attach the fan blade arm to the motor hub are tight housing Make sure wire nut connections are not rattling against each other or the interior wall of the switch Allow a 24 hour breaking in period Most noises associated with a new fan disappear during this The fan sounds noisy time bulb is also secure If u
16. rews Hanging instructions for standard mounting ____________MM 5 Hanging instructions for close to ceiling mounting A WARNING The tab in the ring must rest in the groove of the hanger ball D Failure to properly seat the tab in the groove could cause damage to the wiring Carefully lift the fan motor assembly E up to the mounting bracket A and seat the hanger ball D in the mounting bracket A socket Make sure the tab on the mounting bracket A socket is properly seated in the groove in the hanger ball D This will help to balance the ceiling fan WARNING The hook is only to hold the fan while attaching wiring Failure to hang as instructed may result in the tab breaking causing the fan to fall The hook must pass from the inside to the outside of the canopy Carefully lift the fan motor assembly E up to the mounting bracket A and hang the fan on the hook provided using one of the holes at the outer rim of the canopy B 11 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Assembly Hanging the Fan continued Making the electrical connections WARNING To avoid possible electrical shock be sure AAA BBB CCC electricity is turned off at the main fuse box before wiring WARNING Check to see that all connections are tight AN including ground and that no bare wire is visible at the wire nuts except for the
17. ructions ccceeeseeteeseeeeeeeees 17 Reverse Switch Operating Instructions cseeeeees 17 Care and Cleaning ccccccccssesseeeeeeeeeeeeeeeeeeeeeenseneees 18 Troubleshooting Lama maman 18 Service Parts Ka ANAN KAANAK NANA 20 Safety Information 1 To reduce the risk of electric shock ensure electricity has been turned off at the circuit breaker or fuse box before beginning 2 All wiring must be in accordance with the National Electrical Code ANSI NFPA 70 1999 and local electrical codes Electrical installation should be performed by a qualified licensed electrician 3 The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 Ibs Use only UL listed outlet boxes marked FOR FAN SUPPORT 4 The fan must be mounted with a minimum of 7 ft clearance from the trailing edge of the blades to the floor 5 Avoid placing objects in the path of the blades 6 To avoid personal injury or damage to the fan and other items be cautious when working around or cleaning the fan 7 Do not use water or detergents when cleaning the fan or fan blades A dry dust cloth or lightly dampened cloth will be suitable for most cleaning 8 After making electrical connections spliced conductors should be turned upward and pushed carefully up into the outlet box The wires should be spread apart with the grounded conductor and the equipment grounding condu
18. sing the ceiling light kit make sure the screws securing the glassware are tight Check that the light and outlet box Make sure there is a short distance from the ceiling to the canopy It should not touch the ceiling Make sure your ceiling box is secure and rubber isolator pads are used between the mounting bracket 18 Troubleshooting continued Problem Solution Verify that all blades and blade bracket screws are secure most fan wobble problems are caused by loose parts Once the fan is properly installed run the ceiling fan for 10 minutes to let the fan self adjust If wobble occurs after running the fan for 10 minutes verify blade level using the following process Select a point on the ceiling above the tip of one of the blades then select any fan blade and measure The fan wobbles from the center of the selected blade to the point on the ceiling Rotate the fan until the next blade is positioned and repeat the measurement using the same point from the ceiling for every blade Measurement deviations should be within 1 8 in If all deviations are less than 1 8 in and the fan continues to wobble please call Customer Service 1 877 527 0313 to order a complimentary Blade Balancing Kit If deviation is greater than 1 8 in please call Customer Service 1 877 527 0313 to order complimentary replacements of your brackets 19 HOMEDEPOT COM Please conta
19. the Fan Blades 8 Removing the rubber packing mounts The fan motor assembly E is shipped with rubber packing mounts SS to prevent movement during transportation Remove the five rubber packing mounts SS from the fan motor assembly and discard prior to attaching the blade arms ss 14 9 Attaching the blades to the blade arms Attach blades F to blade arms G using the three screws with fiber washers provided with the blade attachment hardware CC Start a screw with fiber washer CC into the blade arm G but do not tighten Repeat for the two remaining screws and fiber washers CC Tighten each screw securely starting with the center screw Make sure the blade F is straight Repeat steps for the remaining blades Assembly Attaching the Fan Blades continued 1 Fastening the blade assemblies to the motor WARNING To reduce the risk of personal injury do not bend the blade arms G while installing balancing the blades F or cleaning the fan Do no insert foreign objects between rotating fan blades F Align motor holes to blade arms G and secure with screws DD provided tighten screws securely Repeat this procedure for the remaining blade arms G NN Ss PEN L7 VW 15 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Assembly Installing the Light K
Download Pdf Manuals
Related Search