Designers Choice Collection AC17452-ORB Installation Guide
Contents
1. BRACKET a CANOPY g SCREW GP gen COVER FIG 9 FIG 10 FIG 11 FIG 12 2 Screw the bulbs into the sockets see fig 13 3 Be careful not to touch the glass area of the bulb hold with tissue during installation as oil from your hands can cause early lamp failure 4 Put the bottom glass B in the bottom glass FIG 13 T A see fig 14 207080 5 Position the indentations in the outer rim of the glass shade so that they line up with RR CLASS the tabs in the inside surface of the fan light fixture rim Carefully lift the glass shade up inside the light fixture as far as FIG 14 it will go Rotate the shade in a clockwise to the right direction until it is held tightly in place by the three tabs see fig 15 TAB Changing Bulbs SE Ht CS BOTTOM 1 Remove the screw from the round hole FIG 15 EE and untighten the other two screws from the key shape screw holes Twist socket SOCKET holder in counter clock wise direction vr see fig 16 and then lift the socket TA screw holder up for bulbs replacement see fig 17 GLASS 2 After the bulbs are replaced reverse step FIG 16 one to install the socket holder back to light kit plate see fig 18 FIG 17 FIG 18 Operation in Summer In warm weather the reverse switch should be set to produce a downward flow of air The constant gentle breeze will transfer heat from your body thus you will feel cooler even if2. period Most noises associated with a new fan disappear during this time 5 If using ceiling fan light kit make sure the screws securing the glassware are tight Check that the light bulb is also secure 6 Make sure there is a short distance from the ceiling to the canopy It should not touch the ceiling 7 Make sure your ceiling box is secure and rubber isolator pads are used between mounting bracket and outlet box Remote control 1 Do not connect the fan with a wall mounted variable speed control s malfunction 2 Make sure the dip switches are set correctly Lights shut off and will I This unit may be equipped with a wattage limiting device Lamping in not come back on excess of 190 watts will disable your ceiling fan s light kit To reset your light kit you must turn the power off and relamp keeping the wattage under 190 watts Restore power to your ceiling fan and continue normal operation Fan wobble Check that all blade and blade arm screws are secure 2 Most fan wobbling problems are caused when blade levels are unequal Check this level by selecting a point on the ceiling above the tip of one of the blades Measure this distance Rotate the fan until the next blade is positioned for measurement Repeat for each blade The distance deviation should be equal within 1 8 3 Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable 4 If the blade wobble is still noticeable interchanging
3. the temperature remains unchanged This cooling effect is referred to as a wind chill factor In an air conditioned home the wind chill factor will allow you to set the thermostat higher than the usual setting While using less energy to air condition your home you will stay just as cool For summer cooling set the speed control on medium or fast speed This will provide sufficient airflow to accomplish a cooling effect The exception to this is in bedrooms where a brisk downward flow would be too chilly A low speed gentle breeze is all that is necessary to keep you comfortable at night Operating in Winter Winter comfort requires a different approach Because warm air rises the air close to the ceiling is always warmer by perhaps 15 degrees than the air close to the floor To prevent heat from hovering where it does little good move the reverse switch to create an upward airflow This will pull cool air up and force warm air across the ceiling and down the walls Set the variable speed control fast enough to break up the air stratification but slow enough not to create a draft By keeping the heat circulating the heater will not have to operate as often to keep you warm SUMMER r ee GE gt U DO Air is blown down producing a cool breeze WINTER An upward airflow will push warm air off the ceiling and circulate it downwards CARE OF YOUR FAN Here are some suggestions to help you maintain your fan
4. two adjacent side by side blades can redistribute the weight and possibly result in smoother operation WARNING TO REDUCE THE RISK OF PERSONAL INJURY DO NOT BEND THE BLADE ARM WHILE INSTALLING BALANCING THE BLADES OR CLEANING THE FAN DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES TNA11112135
5. 1 Because of the fan s natural movement some connections may become loose Check the support connections brackets and blade attachments twice a year Make sure they are secure It is not necessary to remove fan from ceiling 2 Clean your fan periodically to help maintain its new appearance over the years Use only a soft brush or lint free cloth to avoid scratching the finish The plating is sealed with a lacquer to minimize discoloration or tarnishing Do not use water when cleaning This could damage the motor or the wood or possibly cause an electrical shock 3 You can apply a light coat of furniture polish to the wood blades for additional protection and enhanced beauty Cover small scratches with a light application of shoe polish 4 There is no need to oil your fan The motor has permanently lubricated sealed ball bearings TROUBLESHOOTING Problem Solution Fan will not start 1 Check main and branch circuit fuses or breakers 2 Check line wire connections to the fan and switch wire connections in the switch housing 3 Check to make sure the dip switches from the transmitter and receiver are set to the same frequency Fan sounds noisy Make sure all motor housing screws are snug 2 Make sure the screws that attach the fan blade bracket to the motor hub are tight 3 Make sure wire nut connections are not rattling against each other or the interior wall of the switch housing 4 Allow a 24 hour breaking in
6. CEILING FAN INSTALLATION AND OPERATION MANUAL MODEL NUMBER AC 17452 READ AND SAVE THESE INSTRUCTIONS 10 11 12 To reduce the risk of personal injury do not bend the blades when installing the blades balancing the blades or cleaning the fan Do not insert foreign objects between rotating fan blades SAFETY PRECAUTIONS WARNING INSTALLATION SHOULD BE PERFORMED BY A QUALIFIED ELECTRICAN To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning All electrical connections must be in accordance with local codes ordinances or National Electrical Code If you are unfamiliar with methods of installing electrical wiring secure the services of a qualified electrician Make sure that your installation will not allow rotating fan blades to come in contact with any object If you are installing more than one ceiling fan make sure that you do not mix fan blade sets Only mount fan to outlet box marked acceptable for ceiling fan Installation to a concrete ceiling should be performed by a qualified electrician Before beginning disconnect power by removing fuse or turning off circuit breaker After fan is completely installed make sure that all connections are secured to prevent fan from falling Do not insert anything into the fan blades while ceiling fan is operating Fan must be turned off and stopped before reversing fan direction The fan must
7. be mounted with the blades at least 2 3m from the floor to minimum the possibility of accidental contact with the fan blades The supply wires Live amp Neutral must be connected to wall switch double poles having a contact separation at least 3mm in all poles WARNING The box must be supported directly by the building structure The box and its WARNING support must be able support the fan weight must not twist or work loose Do not use plastic boxes Installing up light Bulbs 1 Before lowering glass switch lock holders outward then switch back lock holder after lowering glass see fig 1 2 Insert the light bulbs into socket in up light socket holder see fig 2 MOTOR COVER FASTENER 3 Remove one screw and loosen the other FIG 1 two screws from the motor housing Place the light kit plate onto the motor by align the screw holes and tighten all screws HOLDER SOCKET J BULB Putting Your Fan Together 1 Remove the two set screws from the motor FIG 2 coupling Remove the hairpin clip amp washer from the clevis pin and remove clevis pin from down rod LIGHT KIT 2 Insert the down rod through the center opening in the canopy canopy hole cover coupling cover and route the motor leads through the hanger ball down rod assembly Align the clevis pin holes in the down prIG 3 rod with the holes in the motor coupling l The clevis pin must pass though the holes HANIA PALU a in the motor coupl
8. he black wire from fan with wire nut Connect the white wire from receiver to the white wire from fan with wire nut Connect the blue wire from receiver to blue wire from fan with wire nut Connect the orange wire from receiver to orange wire from fan with wire nut Connect the green wire from ceiling and green wire from hanger bracket with green wire from the hanger ball with wire nut see fig 8 3 Loosen the two canopy mounting screws from the hanger bracket Mount the canopy on the two screws in the hanger bracket and twist the canopy so the screw heads hold the canopy in place Retighten the two screws and place the canopy hole cover and twist the cover to tighten up see fig 9 Installing Blades Assembly Caution To reduce the risk of personal injury Do not bend the blade when installing balancing or cleaning the fan Do not insert foreign objects between rotating fan blades 1 Install blades to blade bracket and tighten securely see fig 10 2 Attach blade assembly to motor see fig 11 Installing the Light Kit 1 Connect the wires from the fan and from light fixture Place the light kit into the switch housing cover and tighten the screw until it locked see fig 12 ___HANGER CABLE p BRACKET pa DOWNROD WASHER r bs WASHER SCREW FIG 7 BLACK WIRE GREEN WIRE WHITE WIRE pr AVHITE WIRE ORANGE K 2 5 ORANGE WIRE MC BLUE WIRE BLUE SSI HUS WIRE AC gt JG EEN WIRE FIG 8 HANGER
9. ing and the down rod ASSEMBLY 7 lt dl Place the washer onto the clevis pin and install the hairpin clip making sure to push straight leg of the hairpin clip through the hole near hanger ball to make sure the clevis pin is properly installed see fig 4 3 Reinstall the 2 set screws in the motor coupling and securely tighten screws FIG 4 against the down rod assembly i ga OUTLET Hanging Your Ceiling Fan BOX AN 1 Securely attach the hanger bracket to the Ze i J BRACKER outlet box by washers and screws supplied EN Connect white wire from ceiling to white amp VASHER wire from receiver with wire nut Connect REVER SCREW black wire from ceiling to black wire FIG 5 from receiver with wire nut see fig 5 2 Carefully lift the fan and seat the down HANGER rod and ball assembly on the hanger bracket m s s BRACKET Be sure the groove in the ball is lined up UNIT with tab on the hanger bracket Do not f POWNROD pinch wires between the ball and down rod assembly and hanger bracket see fig 6 2 FIG 6 3 Install the safety cable into the building structure see fig 7 Wiring Your Ceiling Fan Caution To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring 1 If you are not sure that the electrical box is grounded contact a licensed electrician for advice It must be grounded for safe operation 2 Connect the black wire from receiver to t
Download Pdf Manuals
Related Search