Hunter 28794 Installation Guide
Contents
1. l Getting Ready To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Keyhole saw e 2 x 4 support brace e UL approved octagonal 4 x 1 1 2 outlet box e Two 8 x 1 1 2 wood screws and washers e Approved connector for electrical wire e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height dependent upon installation site Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 888 830 1326 In Canada call 866 268 1936 6 Installing Multiple Fans If you are installing more than one fan keep the fan blades and blade irons if applicable in sets as they were shipped 42486 01 03 06 12 Hunter Fan Company 2 Installing the Ceiling Plate A CAUTION To avoid possible2. For reference also attach your receipt or a copy of your receipt to the manual For Your Records and Warranty Assistance 9e 2 Mo ode Is ly A a ZNANJ Owner s Guide and Installation Manual Where Purchased SINCE 1886 Form 42486 01 20120306 2012 Hunter Fan Co Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings e READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION SAVE THESE INSTRUCTIONS e Use only Hunter replacement parts e To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions 1 Getting Ready and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a promin
3. Reversing Qe Switch In warm weather use downward air flow pattern In cold weather use upward air flow pattern 17 42486 01 03 06 12 Hunter Fan Company 11 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly left or right to ensure that the switch is engaged 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade assembly screws and blade iron armature screws until snug 2 Check to see if the blade is cracked If so replace all the blades Problem Excessive wobbling 1 Make sure the blades are securely attached to the blade irons according to the blade assembly instructions provided 2 After thoroughly verifying the blades are securely attached to the blade irons follow the instructions in the enclosed balancing kit to balance the fan 3 Turn power off support fan very carefully and check that the hanger ball is properly seated Problem Lights shut off suddenly but fan is still operating 1 Check to make sure the wattage and type of the light bulbs that are installed meet the specifications on the light socket 2 Turn the power to the fan off at the wall switch Wait 5 minutes
4. Assembly Screw 12 42486 01 03 06 12 Hunter Fan Company Step 7 1 Detail Steps 7 1 7 2 8 Completing Your Installation With a Bowl Light Fixture A WARNING Use only the light fixture supplied with this fan model 8 1 Partially install two housing assembly screws into the mounting plate on the bottom of the fan 8 2 Feed the upper plug connector from the motor through the center opening of the shroud 8 3 Slide the partially installed screws through the keyhole slots in the shroud Turn the shroud counter clockwise until the screws are nestled in the narrow ends of the keyhole slots 8 4 Install a third housing assembly screw into the remaining screw hole in the shroud Securely tighten all three screws 8 5 Install six 6 32 machine screws into the outer holes in the shroud Housing Assembly Shroud Screw 13 42486 01 03 06 12 Hunter Fan Company 8 e Completing Your Installation With a Bowl Light Fixture Continued 8 6 Connect the upper plug connector from the fan to the lower plug connector in the light fixture Note Both plug connectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product 8 7 Partially install two housing assembly screws into the shroud 8 8 Slide the keyhole slot
5. Install the 12 volt battery into the transmitter A CAUTION The remote control device complies with part 15 of the FCC rules Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Note Use with a fan that incorporates an air gap switch normal on off wall switch A WARNING Maximum fan load is 1 5 Amp maximum lamp is 120 Watts 9 42486 01 03 06 12 e Hunter Fan Company 5 Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician 5 1 Make sure the power is still off Antenna 5 2 To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight For all these connections use the wire connectors provided A CAUTION Be sure no bare wire or wire strands are visible after making connections a C 5 3 Using a large wire connector connect the ground wire from the Receiver ceiling to the green ground wire from the ceiling plate and the Steps 5 3 5 7 green ground wire from the downrod 5 4 Using the large wire connectors connect the
6. fan The pull chain has four settings in sequence High Medium Low and Off e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector The light pull chain controls the power to the light fixture The chain has two settings ON and OFF Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the Same manner as the fan finish To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the reversing switch on the fan to the opposite position Restart fan
7. supply house 4 2 Orient the outlet box so that both the inner and outer holes in the box align with the joist or support brace 4 3 Drill pilot holes no larger than the minor diameter of the wood screws 5 64 through the inner holes of the outlet box 4 4 Attach the outlet box directly to the support brace or joist with two 8 x 1 1 2 wood screws and washers The bottom of the outlet box must be recessed a minimum of 1 16 into the ceiling Step 5 Prepare the Wiring 5 1 Make sure the circuit breakers to the fan supply line leads and associated wall switch location are turned off If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel 5 2 Thread the fan supply line through the outlet box so that the fan supply line extends at least 6 beyond the box 5 3 Attach the fan supply line to the outlet box with an approved connector available at any hardware store or electrical supply house 5 4 Make certain the wiring meets all national and local standards and ANSI NFPA 70 You have now successfully prepared your ceiling fan site For instructions to install your ceiling fan go to your fan manual and continue with Section 2 Installing the Ceiling Plate 4 42486 01 03 06 12 Hunter Fan Company A CAUTION All wiring must be in accordance with national and local electrical codes and ANSI NFPA 7
8. 0 If you are unfamiliar with wiring use a qualified electrician Installer s Choice and Optional Accessories Support Brace Ceiling Standard Outlet Box Mounting gt Style Standard Mounting hangs from the ceiling by a downrod included Angled Mounting recommended for a vaulted or angled ceiling Understanding Mounting and Installers Choice Hunter s patented 2 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one of two ways depending on ceiling height and your preference Standard or Angled mounting The steps in this manual include instructions for both Installer s Choice mounting methods Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance A CAUTION To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied 5 42486 01 03 06 12 Hunter Fan Company
9. 6 P i DE i IA AA A fal f m ONA Naa gt Oe HA NNA WAPAT A 6 f Gr Oh 9 49 a Breakaway Connector Steps 8 10 8 11 42486 01 03 06 12 Hunter Fan Company 9 1 9 2 9 3 9 Operating the Remote Control and Mounting the Holder The remote has individual buttons for setting the fan speed and light Refer to the figure on the right Note For best operation start the fan by pressing high then select your desired speed The light button turns the light Push the light button again to turn off the light When necessary replace the battery with a 12 volt alkaline battery You can mount the remote holder to any toggle switch plate with the screws already in the switch plate Or you can simply mount the remote holder on the wall Attention Use the pull chain switch to set the fan speed to the position BEFORE installation Do not use pull chain switch to change the fan speed after installation as damage to your fan or remote may result The speed of the fan should only be changed by the Hunter control Set the ceiling fan light kit to the ON position before installation The light level should only be changed by the Hunter control 16 42486 01 03 06 12 Hunter Fan Company 10 1 10 2 10 3 10 4 10 5 10 6 10 Operating and Cleaning Your Ceiling Fan Turn on electrical power to the fan The fan pull chain controls power to the
10. e hanger ball groove Note Your fan may have multiple tabs and grooves that must be aligned Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate A WARNING The slots in the canopy must remain engaged while swinging the canopy for alignment Holding the canopy up with the screw holes aligned partially install two canopy screws into the holes opposite the ceiling plate tabs Partially install a canopy screw between the slots in the canopy When all the holes are properly aligned securely tighten all three canopy screws Verify that the tabs in the canopy are still in the grooves of the hanger ball Align the tabs on the trim ring opposite the grooves in the hanger ball Using both hands push the canopy trim ring up to the top of the canopy The canopy trim ring will snap and lock into place Note Should you need to remove the trim ring press firmly on opposite sides of the trim ring directly above the groove in the hanger ball The tabs will flex out releasing the canopy trim ring Step 6 3 Canopy gt Canopy Trim Canopy Screw lI 42486 01 03 06 12 Hunter Fan Company 7 Assembling the Blades 7 1 Insert grommets into the holes in the blades 7 2 Install one blade onto a blade iron with three blade assembly screws 7 3 Repeat Steps 7 1 7 2 untill all three blades are installed Blade
11. e No object can come in contact with the rotating fan blades during normal operation e The fan blades are at least 7 feet above the floor and the ceiling is at least 8 feet high The fan blades have no obstructions to airflow such as walls or posts within 30 inches of the fan blade tips e The fan is directly below a joist or support brace that will hold the outlet box and the full weight of the fan Checklist for Existing Fan Site e a 30 From Wall or Nearest Obstruction 7 Minimum Blades to Floor 8 Minimum If you want to use an existing fan site complete the following checklist to Fan Support determine if the site is acceptable and safe for your new Hunter fan If you cannot check off every item prepare a new fan site as described on this page Fan Support System Fan attaches directly to building structure e Fan support system will hold full weight of the fan and light kit Ceiling Hole The outlet box clearance hole is directly below the joist or support brace Outlet Box e The outlet box is an UL approved octagonal 4 x 1 1 2 outlet box or as specified by the support brace manufacturer e The outlet box is secured to the joist or support brace by wood screws and washers through the inner holes of outlet box e The outer holes of the outlet box are aligned with joist or support brace e The bottom of the outlet box is recessed a minimum of 1 16 into ceiling Wiring e T
12. electrical shock before installing your fan Toward disconnect the power by turning off the circuit breakers to the outlet box Ceiling Peak and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel 2 1 Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter For Angled Ceilings Be sure to orient the ceiling plate so that the two tabs are pointing toward the ceiling peak For Angled Ceilings Be sure to orient the ceiling plate so that the two tabs 2 2 Your fan comes with four preinstalled noise isolators Check to a a are pointing toward the ceiling peak make sure all four isolators are in place and were not removed during shipment 2 3 Place a flat washer on each of the two 3 wood screws 2 4 Thread the supply wires from the outlet box in the ceiling through the hole in the center of the ceiling plate 2 5 Align the slotted holes in the ceiling plate with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other Note The isolators should be flush against the ceiling 2 6 Pass the screws through the slotted holes in the ceiling plate into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lub
13. ent warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical 6 Installing the Canopy and Canopy Trim codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a Solid state speed control with this fan Use only Hunter speed controls which are solid state Table Of Contents 2 Installing the Ceiling Plate 3 e Assembling and Hanging the Fan 8 4 e Setting the Remote Transmitter and Receiver 5 e Wiring the Fan 7 Assembling the Blades 8 e Completing Your Installation With a Bowl Light Fixture 9 e Operating the Remote Control and Mounting the Holder 10 Operating and Cleaning Your Ceiling e This product conforms to UL STD 507 and is certified to STD C22 2 No 113 11 Troubleshooting e Wash your hands after your fan installation is complete 2012 Hunter Fan Company 9 42486 01 03 06 12 Hunter Fan Company Preparing the Fan Site Step 1 Choose the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings Choose a fan site where
14. he electrical cable is secured to outlet box by an approved connector e Six inches of lead wires extend from outlet box Suitable Existing Fan Site Fan Support System Outlet Box If your existing fan site is suitable skip ahead to Section 2 Installing the Ceiling Plate 3 42486 01 03 06 12 Hunter Fan Company Ceiling Height Preparing the Fan Site continued Step 2 Cut the Ceiling Hole 2 1 Locate the site for the ceiling hole directly below the joist or support brace that will hold the outlet box and fan 2 2 Cut a 4 diameter hole through the drywall or plaster of the ceiling You will use the hole to install the support brace and outlet box Step 3 Install a Support Brace If Necessary Determine if there is a ceiling joist directly above the ceiling hole If the joist is there determine if it is positioned to allow you to recess the outlet box a minimum of 1 16 into the ceiling If NOT install a support brace as follows 3 1 Attach a 2 x 4 support brace between two joists Position it to allow you to recess the bottom of the outlet box a minimum of 1 16 into the ceiling 3 2 Check the support brace to ensure it will support the full weight of the fan and light kit Step 4 Install the Outlet Box 4 1 Obtain a UL approved octagonal 4 x 1 1 2 outlet box plus two 8 x 1 1 2 wood screws and washers available from any hardware store or electrical
15. nd Receiver Setting DIP switches and Jumpers Example DIP Switch Settings Receiver DIP switches When two or more fans are located near each other you may desire TT TET to have the receiver transmitter for each fan set to a different code so that the operation of one fan does not affect the operation of m l 2 9 4 2 4 the other fans DIP Switches DIP Switches Set to 0111 Set to 1111 ON C bos ol be ON 1 a a The DIP switches for the receiver are located on the flat surface of the receiver The Jumpers for the transmitter are in the battery compartment 4 1 IMPORTANT Before you change the Jumper settings make sure the battery is not connected to the transmitter Example Jumpers Settings Se i i Transmitter Transmitter Change the position of the jumpers in the transmitter and the a DIP switches in the receiver Be sure the position of the jumper as anes o ENN ESS in the transmitter matches the position of the DIP switches ae ae in the receiver If they don t match the controller will not Zon ems 2 on fema function For instructions on how to set the jumpers read the box below 4 2 There is a toggle switch beside the DIP switches on the transmitter Move the toggle switch toward the side that reads CFL if you are going to operate the fan with CFL bulbs CFL Toggle Switch Move the switch to the INC side if you are going to use incandescent bulbs 4 3
16. ricants on the screws Do not over tighten Flat Washer 3 Wood Steps 2 3 2 6 Screw ements FEENUNUUEEEEEOUU NUN me 7 42486 01 03 06 12 Hunter Fan Company 3 Assembling and Hanging the Fan A WARNING Fan may fall if not assembled as directed in these installation 3 1 3 2 3 3 Note 3 4 instructions Unbundle the wires from the fan Insert the downrod through the canopy and canopy trim ring Feed the wires from the fan through the downrod on one side of the pin in the ball Loosen the square head setscrew on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly is fully installed 2 3 threads on the pipe will still be visible this is normal Securely retighten the setscrew with a wrench or pliers A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod To hang the fan you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks Raise the fan and align the slots in the canopy with the hooks on the ceiling plate Place the slots over the hooks to hang the fan 8 Steps 3 2 3 3 Downrod Canopy Trim Ring Setscrew 42486 01 03 06 12 Hunter Fan Company 4 Setting the Remote Transmitter a
17. s in the light fixture into the partially installed screws Turn the light kit counter clockwise until the screws are nestled in the narrow ends of the keyhole slots 8 9 Install a third housing assembly screw into the remaining screw hole in the light fixture Securely tighten all three screws A CAUTION Make sure the shroud is securely attached to the switch housing mounting plate Failure to properly attach and tighten all three assembly screws could result in the switch housing and light fixture falling Note In compliance with US federal energy regulations this ceiling fan contains a device that restricts its light output Exceeding the wattage limit marked on the MAX wattage sticker affixed to the light socket s may result in fire hazard or improper operation 14 Housing Assembly Screw 42486 01 03 06 12 Hunter Fan Company 8 e Completing Your Installation With a Bowl Light Fixture Continued 8 10 Install the included bulbs 40W max 8 11 Hold the glass bowl up so it fits in the shroud 8 12 Hold the cover plate up to the bottom of the glass bowl and secure them both by screwing the finial into the threaded rod on the bottom of the light fixture 8 13 Attach the extra pull chains with pendants included to the light and fan pull chains using the breakaway connector You may find the breakaway connector on the end of the extra chains AIA Atya y hy VaN 4gN
18. then resume power to the fan Problem CFL bulbs flicker when controlled by a dimming remote or wall control 1 CFL light bulbs are not usually made for dimming Replace the CFL bulbs with dimmable light bulbs or install the fan in a location without a dimming control If you need parts or service assistance please call 888 830 1326 In Canada call 866 268 1936 or visit us at our website at http www hunterfan com Hunter Fan Company 7130 Goodlett Farms Parkway 400 Memphis Tennessee 38016 18 42486 01 03 06 12 Hunter Fan Company
19. white wire and the black wire from the ceiling as follows e The white Common power wire from the ceiling to the white wire from the receiver marked on red tag NEUTRAL IN e The black power wire from the ceiling to the black wire from Large Wire the receiver marked on red tag LIVE IN Connector 5 5 Using the small wire connectors connect the wires from the fan as follows e The black wire with a white stripe from the fan to the red wire from the receiver marked on white tag LIGHT OUT Small Wire e The black wire from the fan to the black wire from the receiver Connector marked on white tag FAN OUT e The white wire from the fan to the white wire from the receiver marked on white tag COMMON OUT 5 6 Check each connection to make sure no bare wire or wire strands are visible Push all wires and wire connectors except for the white antenna wire from the receiver back through the ceiling plate into the outlet box 5 7 Position the receiver in the canopy so that the antenna is close to the edge of the ceiling plate for clear reception 10 42486 01 03 06 12 Hunter Fan Company 6 Installing the Canopy and Canopy Trim Ring A WARNING Failure to complete the following steps could cause the fan to fall Note It is recommended you use a magnetic tip screwdriver for the following steps 6 1 6 2 6 3 6 6 Rotate the hanger ball so the tab in the canopy is secure in th
Download Pdf Manuals
Related Search