Hunter 53249 Instructions / Assembly
Contents
1. Table of Contents www HunterFan com 1 888 830 1326 Congratulations on purchasing What to Expect with your new Hunter ceiling fan It will Your Installation Ceiling Bracket provide comfort and performance in your home or office for many years This installation and operation manual contains complete instructions for installing and operating your fan We are proud of our work and appreciate the opportunity to ae Blades supply you with the best ceiling fan available anywhere in the world To register your fan please visit www HunterFan com register M0031 01 01 15 13 Hunter Fan Company What to Expect with Your Installation Must be able to secure the fan to building structure or fan rated outlet box You may need a friend to help you Check box to see fan weight If you are unfamiliar with wiring use a qualified electrician D Know your wiring Ceiling angles greater than 34 will require an Angled Mounting Kit See page 4 for details A Assess ceiling angle 30 inches from blade tip to nearest wall or obstruction 7 feet from bottom edge of blade to the floor A Assess location Standard Downrod for ceilings 8 10 feet high Shorter Downrod for fans installed close to ceiling EJ Longer Downrod for ceilings 10 feet or higher LA Select a downrod length2. M0031 01 01 15 13 Hunter Fan Company q www HunterFan com 1 888 830 1326 Read and Save These Instructions This product conforms to UL Standard 507 A WARNINGS w 1 To reduce the risk of fire electrical shock or personal injury mount fan directly from building structure and or an outlet box marked acceptable for fan support of 70 Ibs 31 8 kg and use the mounting screws provided with the outlet box w 2 To avoid possible electrical shock before installing or servicing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel w 3 To reduce the risk of fire electrical shock or motor damage use only Hunter Solid State Speed Controls w 4 To reduce the risk of personal injury do not bend the blade brackets when installing the blade brackets balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades CAUTIONS c 1 All wiring must be in accordance with national and local electrical codes ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician c 2 Use only Hunter replacement parts Tools Needed www HunterFan com 1 888 830 1326 amp L Ladder L Pliers L Wire Strippers E Power Drill 9 64 Drill Bit optional
3. optional If mounting to a support structure you will also need these tools M0031 01 01 15 13 Hunter Fan Company 3 4 CEILING a P Mounting Options www HunterFan com 1 888 830 1326 f ka ea a ra ka ea ra a ra e o N o o O a egoe U s If you have a flat ceiling Hang your fan by a standard downrod included Standard Support Support Mounting Structure T O If you have an angled ceiling InN 0 1 You will need a longer downrod sold separately Outlet Box 2 If your ceiling angle is greater than 34 you will Angled Ceilin required also need an Angled Mounting Kit sold separately Mounting N Outlet e required Mounting Use the three steps below to determine if your ceiling angle is greater than 34 Use Standard Mounting Use Angled Mounting BOTH Ceiling amp Wall or Low Profile Mounting to hang the fan from a You need ONLY to hang the fan from a flat ceiling vaulted or angled ceiling a Longer Downrod most common Mounting Kit M0031 01 01 15 13 Hunter Fan Company Ceiling Bracket Make sure all four 4 bumpers are still attached For angled ceilings point opening toward peak If you are unable to do this call Technical Support at 1 888 830 1326 Refer to warning w 1 on pg 2 Use wood screws included when securing to support structure with approved electrical outlet bo
4. g from the ceiling to the blue hanging bracket L the white wire from the fan To wire from the fan p punobun For a Single Switch G M 2 D A Z Turn the splices upward and push them carefully back through the hanger bracket into the outlet box Spread the wires apart with the grounded wires on one side of Refer to CAUTION c 1 on pg 2 the outlet box and the ungrounded wires on the other side of the outlet box M0031 01 01 15 13 Hunter Fan Company www HunterFan com 1 888 830 1326 gt Hell ALK i gt SE Position the canopy so that when Lift the canopy into place so that Insert the two canopy screws lifted into place the canopy fits into the screw holes are aligned found in the hardware bag the hanging bracket as shown Note Fan style may vary M0031 01 01 15 13 Hunter Fan Company Blades lron Post Align the three blade holes with the three blade iron posts Squeeze the blade and the blade iron post together The flared tops of the blade iron posts will be fully visible above the blade when properly assembled M0031 01 01 15 13 Hunter Fan Company www HunterFan com 1 888 830 1326 Your blades are shielded with Dust Armor which is a nanotechnology coating that repels dust For cleaning the fan use soft brushes or cloths to prevent scratching Cleaning agents may damage the finishes Light Kit www Hunter
5. least 8 extending with pliers DO NOT from the top of the downrod HAND TIGHTEN If the setscrew is not tightened securely the fan may fall M0031 01 01 15 13 Hunter Fan Company Downrod continued www HunterFan com 1 888 830 1326 Put the wires and downrod through the DO NOT PICK THE FAN UP BY THE canopy Let the canopy sit loosely on CANOPY OR WIRES Place the downrod top of the fan ball into the slot in the ceiling bracket M0031 01 01 15 13 Hunter Fan Company a 4 x www HunterFan com 1 888 830 1326 Note To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight 6uipunoi p puno19 p puno19 For Dual Switches Using orange wire connectors from the X hardware bag connect the white wire grounded from the Using an orange wire Using the orange wire ceiling to the white wire connector from connectors from from the fan the X hardware bag the X hardware bag connect Connect the black wire connect the 3 grounding the black wire ungrounded ungrounded from the wires green green from the ceiling to the black l ceiling to the black wire yellow stripe or bare and the blue wires from the rey M S from the fan Connect the copper coming from the fan Connect the white wire ww 2S second ungrounded wire ceiling downrod and grounded from the ceiling to D
6. Fan com 1 888 830 1326 Housing Screw Switch Housing Screw Partially install two of the switch housing screws found in the bag Connect Align the notches in the sides of the lower switch housing with the upper switch 0 Install the third switch housing screw Tighten all three screws securely the plugs from the upper and lower switch housings Make sure to line up the colored markings on the connectors housing screws Lift the lower switch housing Twist the lower switch housing clockwise to lock into place Then thread the fan pull chain through the hole in the light kit l Want to install your fan without a light kit Make sure the lower switch housing is securely attached to Go to www HunterFan com FAQs and click the upper switch housing Failure to properly secure all three au e switch housing screws could result in the light fixture falling How do install my fan without the light kit 12 M0031 01 01 15 13 Hunter Fan Company Light Kit continued www HunterFan com 1 888 830 1326 i ae Traen a a AELS e w u T Install a light bulb in each socket Press the globe and globe keeper Connect the appropriate pull flush against the metal plate Thread chain pendant to each of the the light pull chain through the hole short chains coming from the in the center of the finial cap and finial and finial cap The fan pull SS eee sh
7. ad pe chain controls the speed from See next page for fan es a 3 a mean high to off The light pull chain operation instructions thread only the light pull chain controls the light fixture on and through the hole in the finial and ff screw the finial onto the threaded rod 3 M0031 01 01 15 13 Hunter Fan Company Note Globe style and number of lights may vary Maintenance amp Cleaning www HunterFan com 1 888 830 1326 D Z Ww s WERS HSN NA UEN Globe Globe Eg Keeper Finial Reverse Cap witc Be Finial Changing the bulbs Unscrew Changing the direction of air Cleaning the fan use soft the finial and remove it from the flow move the reverse switch brushes or cloths to prevent threaded rod Remove the finial cap to the opposite position scratching Cleaning products and unscrew the globe keeper while may damage the finishes supporting the globe with your other hand Carefully remove the globe Unscrew bulbs and replace with bulbs of same type and wattage Reinstall the globe assembly x i For questions regarding removing a light kit call customer service 1 888 830 1326 M0031 01 01 15 13 Hunter Fan Company Troubleshooting Fan doesn t work e Make sure power switch is on Pull the pull chain to make sure it is on Push the motor reversing switch firmly left or right to ensure that it is engaged Check the circuit breaker to ensure t
8. he power is turned on Make sure the blades spin freely Turn off power from the circuit breaker then loosen the canopy and check all the connections according to the wiring diagram on page 7 Check the plug connection in the switch housing Excessive wobbling e Tighten all of the blade and blade iron screws until they are snug e Use the provided balancing kit and instructions to balance the fan Noisy Operation e Tighten the blade and blade iron screws until they are snug e Check to see if any of the blades are cracked If so replace all of the blades M0031 01 01 15 13 Hunter Fan Company www HunterFan com 1 888 830 1326 2 Year Energy Star Light Kit Warranty The Hunter Fan Company Inc makes the following warranty to the original user or consumer purchaser of each Hunter Energy Efficient Light Kit If your Hunter Energy Efficient Light Kit fails at any time within two years after the date of sale due to a defect in material or workmanship labor to repair the defect will be provided free of charge at our nearest service center or our service department in Memphis TN You will be responsible for all labor costs after this two year period This warranty is voided if this product is not purchased in the U S A or Canada This warranty excludes and does not cover defects malfunctions or failures of any product which were caused by repairs by persons not authorized by us use of parts or acces
9. sories not authorized by us mishandling improper installation modifications or damage to the light fixture while in your possession or unreasonable use including failure to provide reasonable and necessary maintenance INNO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE
10. x Drill 9 64 pilot holes in support structure to aid in securing ceiling bracket with hardware found in the k hardware bag www HunterFan com 1 888 830 1326 NNN MINNN Use machine screws provided with outlet box when securing to existing ceiling fan rated outlet box Make sure it is securely installed and is acceptable for fan support of 31 8 kg 70 Ibs or less To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location M0031 01 01 15 13 Hunter Fan Company Downrod www HunterFan com 1 888 830 1326 Standard Downrod skip to next page for ceilings 8 10 high If you need a different downrod length follow these steps Longer Steps 1 5 to remove standard downrod pipe Downrod for angled ceilings or ceilings 10 or higher Included pre assembled Shorter Downrod for fans installed close to ceiling Included Sold Separately Steps 6 10 to reassemble with new pipe M0031 01 01 15 13 Hunter Fan Company Downrod continued www HunterFan com 1 888 830 1326 T U YN O O j il Remove the pre installed setscrew so that the downrod can be inserted Hand tighten the downrod at The wires can be cut but Tighten the setscrew least 4 5 full turns until it stops leave at
Download Pdf Manuals
Related Search