Sea Gull Lighting 31627BLE-962 Installation Guide
Contents
1.2. Na Installation And Safety Instructions il li hbj Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to 56d gu ig mg this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM IMPORTANT SAFETY INSTRUCTIONS Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off Use of other manufacturers components will void warranty listing and create a potential safety hazard If you are unclear as to how to proceed contact a qualified electrician You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully Save these instructions MOUNTING CLEANING BAR A To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders OUTLET BOX SCREWS E q j NIPPLE C an 0 2 ie Q e log f 2 lt 0 me me D 5 ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illust
3. acer to the supply hot wire B Use a listed wire connector to connect the fixture common wire white wire or square and rigid to the supply common wire C Gently try to remove the wires from the connector If you can remove the wires carefully re do the wiring connection STEP 6 GROUNDING INSTRUCTIONS Connect the supply ground wire fixture ground wire and mounting bar ground wire pre attached using the supplied wiring connector Gently try to remove the wires from the connector If you can remove j n iri i MOUNTING the wires carefully re do the wiring connection BAR A WIRE CONNECTORS NUT B GROUND 1B GREEN WIRE F o GROUNDING SCREW D FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors COLLAR E After wires are connected tuck them carefully inside outlet box Raise canopy H against ceiling and thread the screw collar ring G CANOPY H to the screw collar E dh SCREW COLLAR RING G Place glass R in socket cup I and secure by threading retaining CHAIN S ring O onto socket STEP 9 FIXTURE LOOP J Install self ballasted lamp P by twisting into socket Q RETAINING MARK MEANS LAMP CONTAINS MERCURY FOLLOW DISPOSAL LAWS SEE WWW LAMPRECYCLE ORG FIXTURES WITH A ONE PIECE LAMP BALLAST COMBINATION SELF BALLASTED gt _ ARMS M SOCKET Q gt IO FIGURE 3 FIGURE 2 NOT INCLUDED
4. ration when ordering parts BEFORE YOU BEGIN Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 and Figure 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture FIXTURE LOOP J INSTALLATION IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Rotate arms M Thread fixture loop J to top of fixture STEP 2 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 3 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B Thread screw collar E to nipple C STEP 3 Using 2 pairs of pliers or chain breaks open one link of chain S and connect it to the fixture loop J at the top of the fixture Please be sure to open chain link in an outward motion Do not twist STEP 4 Slide the screw collar ring G and canopy H in that order over chain S Open one link on the other end of the chain S and attach it to the screw collar E which has been mounted to the nipple C FIGURE 1 BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY ARMS M HC 1575 090909 NUT B GREEN GROUNDING SCREW D SCREW COLLAR E SCREW COLLAR RING G NOT INCLUDED INSTALLATION continued HC 1575 STEP 5 A Use a listed wire connector to connect the fixture hot wire black wire or round and smooth tr
Download Pdf Manuals
Related Search