Hunter 99107 Use and Care Manual
Contents
1. 2014 Hunter Fan Company 6 setup Record PIN Write down the PIN located on the Bluetooth plug in controller You will need the PIN to complete step 5 1 Plug in the Bluetooth Plug in Controller 2 Launch the app Ensure that Bluetooth is enabled on your device before launching the app 3 Tap the Controller button If you are installing multiple Bluetooth plug in controllers be sure to tap the Controller button that coincides with the correct Bluetooth plug in control Enter the PIN The 4 digit PIN can be found on the Bluetooth plug in controller Tap Done when finished 4 5 The Bluetooth plug in controller works up to 80 feet from the fan receiver Congratulations You have successfully set up your programmable control You may now begin using the app to take control of your fan See the step by step tutorial in the app to learn more Remember The app only works while in range of the Bluetooth plug in controller If you would like your fan and lights to operate while you are away you must first use the app to schedule an event Dimming In the app navigate to the Rooms Configured settings screen and tap the Gear icon next to your room Here you can turn the dimming feature on or off This may cause faulty operation if your bulbs do not support dimming PIN If you have not downloaded the app do so now Visit your app store and search simpleconnect Install 7 M32. Go to Advanced Features Tap the Pair button If your bulbs support dimming you may also turn on the dimming feature at this screen To prevent faulty operation please disconnect power from all other ceiling fans within range while performing the next three steps i icon M3561 01 01 26 15 2014 Hunter Fan Company 8 optional ON OFF remote pairing No Pairing Required The optional ON OFF remote is already paired to the receiver and ready to use If the battery is working the buttons should illuminate when pressed but the remote does not operate the fan or if you would like to pair the remote to additional receiver s please see the Troubleshooting section on the following page Fan Operation Press and release the Fan button on the remote control to turn the fan off or on Light Operation Press and quickly release the Light button on the remote control to turn the light off or on operation Light Control Fan Control maintenance Installing Replacing the Battery To access the battery compartment remove the small Phillips head screw that secures the battery door to the transmitter assembly The battery should be installed with the positive side up Replace with a CR2032 battery when necessary Phillips Head Screw Battery Door 9 M3561 01 01 26 15 2014 Hunter Fan Company CFL Bulbs Flicker Tap the Gear icon in the Room setup screen to visit the set
3. is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connec
4. 561 01 01 26 15 2014 Hunter Fan Company You can now reconnect power to your other fans Tap the Gear icon shown below Be sure to choose a Gear icon for a room that is not already configured Note There is a maximum four rooms per Bluetooth plug in controller For further details on installing and controlling multiple fans refer to the Information page in the app by tapping on the i icon a Gear icon b c Cycle power to the fan Turn power off and back on at the wall or circuit breaker if necessary The next step must be completed WITHIN THREE MINUTES of restoring power to the fan d Tap OK to confirm pairing Note The lights will flash if applicable and the fan will turn on at low speed This is visual confirmation that the pairing was successful Congratulations You have successfully set up your additional receiver Tap the Back button twice to begin using the app to take control of your fan setup for additional fans using a single Bluetooth plug in controller If you wish to operate multiple fans with one Bluetooth plug in controller 1 You will need an additional receiver sold separately for each fan Complete the Installation section to install each receiver into your fan s Receivers can be purchased at www HunterFan com 2 Tap the Gear icon on the main screen to navigate to the Rooms Configured settings screen 3 Perform steps a d on this page to complete setup
5. M3561 01 01 26 15 2014 Hunter Fan Company installation and setup guide programmable control model 99107 M3561 01 01 26 15 2014 Hunter Fan Company 2 If your fan has pull chains use the pull chains to set the fan speed to HIGH and the light to ON before disconnecting power 1 Unscrew and lower the canopy Remove the wire connectors that connect the wires from the ceiling to the fan leaving the grounding wires connected If uncertain how to do this reference the fan s owner s manual Hunter fan manuals can be found on www HunterFan com Note With wiring exposed it may be helpful to note existing wire connections or to take a digital photo for reference before removing the wire connectors 3 installation Ensure that power is OFF at the circuit breaker before proceeding with installation 2 OFF Turn Power Prior to installation download the app to ensure phone compatibility Visit your app store and search simpleconnect to find the app 3 M3561 01 01 26 15 2014 Hunter Fan Company Ceiling Plate Receiver Canopy Receiver Canopy Ceiling Bracket Receiver Fan Body Cable Tie Receiver Canopy Choose the hanging system that most closely resembles the one used by your fan and place the receiver as shown 4 Note If your canopy is crowded with excess wire you may wish to cut the excess fan wires Leave a minimum of 8 inches remaining Strip the f
6. S WARRANTY SET FORTH ABOVE FOR SUCH CONTROL This warranty excludes malfunctions or failures which were caused by repairs by persons not authorized by us mishandling improper installation modifications or damage to the Control while in your possession or unreasonable use This warranty does not apply to batteries or to deterioration or damage to the product caused by the use of faulty batteries IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Compatible with iOS 7 1 or higher Android 4 3 or higher Android and Google Play are trademarks of Google Inc Apple logo is a trademark of Apple Inc App store is a service mark of Apple Inc Bluetooth is a registered trademark of Bluetooth SIG
7. an lead wires 1 2 inch Place remaining excess wire into the ceiling electrical box The bracket and fan must remain properly grounded If the fan is installed on an angled ceiling and you need assistance with installation please call 1 888 830 1326 For low profile fans secure the receiver to the ceiling bracket with a cable tie installation continued WARNING This receiver cannot be installed in conjunction with any other receiver or hard wired wall control Doing so will void your warranty Hanging System 1 Hanging System 2 Hanging System 3 Hanging System 4 M3561 01 01 26 15 2014 Hunter Fan Company 4 5 Using the wire connectors Connect the blue wire from the receiver to the light wire blue or possibly black with white stripe from the fan Connect the yellow wire from the receiver to the motor wire black from the fan F R O M R E C E I V E R black blue or black white stripe yellow blue F R O M F A N Connect wires from the receiver to wires from the fan as shown Note If you re uncertain about wire colors or connections please contact a qualified electrician Turn the connectors upward and push them carefully back through the hanger bracket into the outlet box Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box To avoi
8. d possible electrical shock before installing or servicing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel installation continued 5 M3561 01 01 26 15 2014 Hunter Fan Company After all wires are connected and secured with wire connectors reinstall the canopy If uncertain how to install the canopy reference the fan s owner s manual F R O M C E I L I N G F R O M R E C E I V E R black white white grounded black ungrounded white F R O M F A N Connect wires from the fan and receiver to wires from the ceiling as shown 6 Using the wire connectors Connect the black wire ungrounded from the ceiling to the black wire from the receiver Connect the white wire grounded from the ceiling to both the white wire from the receiver and the white wire from the fan Note If you re uncertain about wire colors or connections please contact a qualified electrician 7 Restore power at the circuit breaker 8 installation continued Note If you have a dual switch please cap the secondary power wire from the ceiling This will result in one unused switch M3561 01 01 26 15
9. ted Consult the dealer or an experienced radio TV technician for help Note Any changes or modifications to the transmitter or receiver not expressly approved by Hunter Fan Company may void one s authority to operate this remote control Read and Save These Instructions This product conforms to UL Standard 60950 WARNINGS If you have problems or questions please contact us 1 888 830 1326 www HunterFan com 7130 Goodlett Farms Pkwy Ste 400 Memphis TN 38016 HUNTER FAN COMPANY CONTROL LIMITED WARRANTY The Hunter Fan Company makes the following limited warranty to the original purchaser of the receiver Bluetooth controller and optional ON OFF remote collectively the Control Your Control is warranted to be free from defects in material and workmanship for a period of one year from the date of sale If the Control malfunctions or fails within the warranty period due to a defect in material or workmanship we will replace it free of charge IF THE ORIGINAL PURCHASER CEASES TO OWN THE CONTROL THIS WARRANTY AND ANY IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE VOIDED THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES THE DURATION OF ANY IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN RESPECT TO ANY CONTROL IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRES
10. tings screen for the appropriate room or fan If Dimming Mode is on turn off Dimming Mode If the problem is not corrected unpair and re pair the device with Dimming Mode disabled Fan will not start Make sure the power is on at the circuit breaker and the wall switch Make sure that the transmitter and receiver are paired Check wire connections inside of the canopy ON OFF remote only works when held at close range Change battery App does not control the fan as expected Move the Bluetooth plug in controller to a nearby outlet within the same room The app will automatically reconnect with the Bluetooth plug in controller ON OFF remote is not paired The ON OFF remote should already be paired to the fan receiver If the ON OFF remote is not paired perform the following steps 1 To prevent faulty operation please disconnect power from all other ceiling fans within range while performing these steps 2 Turn the fan power off and back on at the wall switch or circuit breaker if necessary 3 Within three minutes of restoring power to the fan press and hold both the Fan button and the Light button for at least four seconds Note The lights will flash if applicable and the fan will turn on at low speed This is visual confirmation that the pairing was successful troubleshooting M3561 01 01 26 15 2014 Hunter Fan Company 10 This device complies with part 15 of the FCC Rules Operation
Download Pdf Manuals
Related Search