Hunter 27183 Instructions / Assembly
Contents
1. Quiet Fan Control with Light Dimmer Ratings 120 VAC 1 6 A 60 Hz 4 Speed Fan and Light Dimmer Slide Preset Control Model 27183 Read and save these instructions Caution Risk of Electrical Shock All wiring must be performed in accordance with national and local electrical codes To avoid overheating and possible damage to other equipment do not install to control a receptacle fluorescent light fixture motor operated appli ance or transformer supplied appliance Use only to control one paddle blade ceiling fan and incandescent light fixture 3 Disconnect power to the ceiling fan and light at the main electric panel Remove fuse or switch circuit breaker to the OFF position 4 Refer to the Installation Figure for your All Fan speed control Remove wallplate to expose the wiring Identify the wires supplying power to the ceiling fan and fan light kit Install in a metal or plastic wallbox 5 Disconnect the existing switch s and remove from the switch box 6 Use the wire nuts supplied to make the ceiling fan and fan light kit connections as shown in the Wiring Diagram If a ground wire is provided in your electrical box attach it to the ground screw near the bottom of the mounting plate 7 Gently push wires and speed control into wall box Attach the All Fan control to the Notes 1 For use only with electrically reversible ceiling fans rated at 1 6 A or less and fan light kits rated at 3002. watts total or less Not for use with any other lighting fixtures or electrical appli ances 2 Not for use with shaded pole or non reversible motors Not recommended for use with the Hunter Original For Hunter Original series fans use Hunter control model numbers 22691 26591 or 22798 3 This control requires separate wiring for the ceiling fan and fan light kit If one wall switch currently supplies power to both the fan and light additional wiring for the light fixture will be required to use this All Fan control 4 MEDIUM and both LOW speeds may vary from the ceiling fan s factory set speeds because of motor variations y Switch box with the two screws supplied 8 M ount wallplate over control with existing screws 9 Move both sliders to the OFF position 10 Restore power at main electrical panel 11 Operate ceiling fan by moving the fan speed slider to the desired speed Dim the light fixture by raising the light dimmer slider to the desired light level The fan and light are turned Off at the bottom position The preset switch beneath the sliders may be used to turn both fan and light ON or OFF at a preset level For best fan operation select HIGH speed until motor starts then select desired speed Installation Instructions 1 Set the ceiling fan s speed to the HIGH position before installation Do not change the ceiling fan s speed setting after your speed control is install
3. tierra con ctelo al tornillo di tierra ubicado cerca de la placa de montaje inferior 7 Empuje los alambres y el control de velocidad con mucho cuidado dentro de la caja del interruptor Asegure el control a la caja del interruptor con los dos tornillos suministrados 8 Monte la placa de la pared sobre el control con los tornillos existentes damage to the product caused by the use of faulty batteries To obtain a replacement return your Control postage prepaid along with proof of purchase to Hunter Fan Company Service Department at 2500 Frisco Avenue Memphis Tennessee 38114 IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITA TIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Form 41314 6 98 y
4. ed as damage to your ceiling fan or All Fan control may result 2 Verify proper operation of the ceiling fan and fan light kit wall switches before installation Improper wiring can damage the control and will void the warranty 120VAC 4 Y 60Hz Light O Neutral Y Wiring Diagram vV Ventilador de 4 velocidades Control para oscurecer la luz Lea y guarde estas instrucciones Cuidado Riesgo de choque el ctrico Todo el cableado y conexiones se deben hacer de acuerdo con los c digos el ctricos nacionales y locales Notas 1 Para uso solamente con ventiladores de cielo raso el ctrica mente reversibles de capacidades de 1 6 A o menores y conjun tos de luces para ventilador con una capacidad total de 300 watts o menor No se debe usar con ninguna otra l mpara ni aparato el ctrico 2 Este control requiere circuitos separados para el ventilador de cielo raso y el conjunto de luces Si el mismo interruptor de pared suministra actualmente la energ a tanto para el ventilador como para las luces se necesitar instalar un circuito separado para el conjunto de luces 9 Mueva las dos palancas deslizables a la posici n OFF apa gada 10 Vuelva a conectar la energ a el ctrica en el panel el ctrico principal 11 Haga funcionar el ventilador de cielo raso moviendo la palanca deslizable a la velocidad deseada Haga oscurecer la luz deslizando la palanca del control de luz al nivel de ilumi
5. locidad All Fan Retire la placa de la pared para exponer los cables Identifique los alambres que suministran period of one year from the date of sale If the Control malfunctions or fails within the warranty period due to a defect in material or workman ship we will replace it free of charge IF THE RIGINAL PURCHASER CEASES TO OWN THE ONTROL THIS WARRANTY AND ANY MPLIED WARRANTY INCLUDING BUT NOT MITED TO ANY IMPLIED WARRANTY OF ERCHANTABILITY OR FITNESS FOR A PAR CULAR PURPOSE ARE VOIDED THIS WAR ANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES THE DURATION OF ANY IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PAR TICULAR PURPOSE IN RESPECT TO ANY CON TROL IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH CONTROL This warranty excludes malfunctions or failures which were caused by repairs by persons not authorized by us mishandling improper installation modifi cations or damage to the Control while in your possession or unreasonable use This warranty does not apply to batteries or to deterioration or 00 x energ a al ventilador y al conjunto de luces 5 Desconecte el los interruptor es existente s y re relo s de la caja 6 Use las tuercas de alambre suministradas para hacer las conexiones como se muestran en el Diagrama de Conexiones Si su caja el ctrica contiene un alambre de
6. naci n deseado El ventilador y las luces est n apagados OFF en la posici n inferior del control Se usa un interruptor preajustado para encender y apagar tanto el ventilador como las luces a un nivel predeterminado Para la mejor operaci n del ventilador seleccione Alta Velocidad hasta que el motor arranque y entonces seleccione la velocidad deseada HUNTER FAN COMPANY ALL FAN CONTROL LIMITED WARRANTY The Hunter Fan Company makes the following limited warranty to the original purchaser of the ALL FAN Control Control Your Control is warranted to be free from defects in material and workmanship for a Instrucciones de instalaci n 1 Coloque el control de velocidad del ventilador de cielo raso en la posici n de Alta Velocidad antes de instalar este control No cambie el ajuste de velocidad de su ventilador de cielo luego de tener instalado el control de velocidad puesto que podr a da ar su ventilador de cielo o el control All Fan 2 Verifique que los interruptores de pared del ventilador de cielo raso y del conjunto de luces trabajen correctamente antes de la instalaci n Las conexiones incorrectas pueden da ar el con trol y anular n la garant a 3 Desconecte la energla el ctrica del ventilador de cielo raso en el panel el ctrico principal Retire el fusible o coloque el disyuntor en la posici n OFF apagado 4 Vea la ilustraci n que muestra la instalaci n de su control de ve
Download Pdf Manuals
Related Search