Sea Gull Lighting 31851-965 Installation Guide
Contents
1. E F S e SCREW COLLAR E a CANOPY H ee GROUNDING SCREW COLLAR SUNEK S RING G FIGURE 2 NOT INCLUDED CHAIN S FIXTURE LOOP J ARMS M gt SOCKET CUP I gt GLASS R RETAINING RING 0 NOT SUPPLIED FIGURE 1 INSTALLATION HC 1285 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 3 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B Thread screw collar E to nipple C STEP 2 Using 2 pairs of pliers open one link of chain S and connect it to the fixture loop J at the top of the fixture STEP 3 Slide the screw collar ring G and canopy H in that order over chain S Open one link on the other end of the chain S and attach it to the screw collar E which has been mounted to the ceiling nipple C BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE l HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED CI y Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is rou2. Installation And Safety Instructions HC 1285 Sea Gull Lighting Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM _ 091007 IMPORTANT SAFETY INSTRUCTIONS BEFORE YOU BEGIN e Be sure the electricity to the system you are working on is turned off Carefully remove the fixture from the carton and check that all either the fuse removed or the circuit breaker set at off parts are included as shown in Figure 1 2 amp 3 Be careful not e Use of other manufacturers components will void warranty listing and to misplace any of the screws or parts which are needed to create a potential safety hazard install this fixture e You don t need special tools to install this fixture e Be sure to follow the steps in the order given STEP 1 e Read instructions carefully oe Rotate arms e If you are unclear as to how to proceed contact a qualified electrician e To reduce the risk of fire electric shock or personal injury mount to outlet box or supporting system able to support the weight of the fixture e Save these instructions GROUNDING AND MOUNTING BAR LOCK UP g OUTLET BOX fo So BOX R Oo CO iS TASNA WIRE CONNECTORS GROUND WIRE EROUN GREEN r lt 2 lt MOUNTING BAR A SCREW D A i NUT B NIPPLE C lt GROUND WIR
3. collar ring G to the screw collar E STEP 2 Place glass R in socket cup I and secure by threading retaining ring O onto socket STEP 3 Install lamps not supplied CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
4. nd in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector clockwise until you feel a firm resistance D Gently try to remove the wires from the connector If you can pull the wires out carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire F from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire F from the fixture if supplied and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box Raise canopy H against ceiling and thread the screw
Download Pdf Manuals
Related Search