Sea Gull Lighting 61625BLE-962 Installation Guide
Contents
1. G in that order to top of socket assembly U Be sure not to damage the fixture wire Thread rod assembly E or chain coupling to nipple of the coupling J at the o Q Q o D Q OUTLET BOX STEP 5 A Use a listed wire connector to connect the fixture hot wire black wire or round and smooth tracer to the supply hot wire B Use a listed wire connector to connect the fixture common wire B white wire or square and rigid to the supply common wire MOUNTING V C Gently try to remove the wires from the connector If you can BAR A A GREEN GROUNDING remove the wires carefully re do the wiring connection SCREW D WIRE CONNECTORS gt f gt NUT C STEP 6 GROUNDING INSTRUCTIONS Connect the supply ground wire fixture ground wire and mounting bar ground wire pre attached using the supplied wiring connector Gently try NIPPLE I to remove the wires from the connector If you can remove the wires CANOPY G carefully re do the wiring connection SCREW COLLAR B SCREW COLLAR RIN COUPLING J FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 7 After wires are connected tuck them carefully inside outlet box and then raise the canopy G against the ceiling Secure by threading screw collar ring K onto screw collar B STEP 8 vu D a o o gt D oO R securely in socket assembly U Secure by threading retaining ring T onto so2. ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Secure mounting bar A to outlet box using outlet box screws not supplied Thread nut C onto nipple I so five threads are exposed Thread nipple I to mounting bar A and secure by tightening nut C to mounting bar A Thread screw collar B to nipple I STEP 2 gt a a D 3 oe 3 a je n A D 3 om lt E by threading desired amount of rods together STEP 3 Feed the fixture wire from the socket assembly U through the rod assembly E and thread rod assembly E into socket assembly U If using optional chain thread coupling at one end of chain into rod assembly E or socket assembly U MARK MEANS LAMP CONTAINS MERCURY FOLLOW DISPOSAL LAWS SEE WWW LAMPRECYCLE ORG Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM WIRE CONNECTORS MOUNTING BAR A NUT C CANOPY G SCREW COLLAR B COUPLING J NOTE THIS FIXTURE CAN BE HUNG USING 1 2 OR 3 RODS SELECT THE NUMBER OF RODS DESIRED FIGURE 1 HC 1580 091009 OUTLET BOX NIPPLE I SCREW COLLAR RING K ROD ASSEMBLY E FIXTURE LOOP F SOCKET ASSEMBLY U SHADE R RETAINING RING T NOT INCLUDED INSTALLATION continued HC 1580 STEP 4 Slide screw collar ring K and canopy
3. Na Installation And Safety Instructions Sea gull lighting IMPORTANT SAFETY INSTRUCTIONS Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off Use of other manufacturers components will void warranty listing and create a potential safety hazard If you are unclear as to how to proceed contact a qualified electrician You don t need special tools to install this fixture Be sure to follow the steps in the order given Read instructions carefully Save these instructions CLEANING 3 o oO jab O oO sh x A oO g jad no a gt o O Q a Q oO jab a jad wn n g jad 3 a no fe jad To Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts BEFORE YOU BEGIN Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 Be careful not to misplace any of the screws or parts which are needed to install this fixture STEP 1 Feed the fixture wire through the fixture loop F and thread fixture loop F to top of the socket assembly U INSTALLATION IMPORTANT DO NOT
4. cket P ROD ASSEMBLY E STEP 9 Install self ballasted lamp O by twisting into socket P FIXTURES WITH A ONE PIECE LAMP BALLAST COMBINATION SELF BALLASTED gt o NOTE THIS FIXTURE CAN BE HUNG USING 1 2 OR 3 RODS SELECT THE NUMBER OF RODS DESIRED SOCKET ASSEMBLY U SHADE R RETAINING RING T SOCKET P gt C D j FIGURE 3 FIGURE 2 NOT INCLUDED
Download Pdf Manuals
Related Search