Kenroy Home 21395ORB Installation Guide
Contents
1. OR BREAKER TO THE OFF POSITION SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES F YOU DO NOT HAVE ELECTRICAL WIRING EXPERIENCE HAVE YOUR FIXTURE INSTALLED BY A QUALIFIED LICENSED ELECTRICIAN THIS FIXTURE IS TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE WEIGHT OF THIS FIXTURE THE OUTLET BOX MUST BE DIRECTLY SUPPORTED BY THE BUILDING STRUCTURE NOTE IF WIRING TO OUTLET BOX FOLLOW INSTRUCTIONS BELOW IF USING POWER CORD PROCEED TO ASSEMBLY INSTRUCTIONS INSTALL THE FIXTURE 1 REMOVE POWER CORD REFER TO REMOVING THE POWER CORD INSTRUCTIONS 2 ATTACH MOUNTING PLATE TO OUTLET BOX USING TWO SCREWS PROVIDED WITH THE OUTLET BOX NOTE IF THE SCREWS WITH THE OUTLET BOX ARE TOO SHORT USE THE 2 8 32 x 1 1 4 SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE 3 CONNECT THE WHITE OR RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTOR PROVIDED CONNECT THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE SAME MANNER INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE MOUNTING PLATE THEN CONNECT THE FIXTURE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTOR PROVIDED 4 RAISE FIXTURE TO THE WALL AND CAREFULLY TUCK THE WIRES INSIDE THE OUTLET BOX SPREAD THE ELECTRICAL SPLICES SO THAT THE BLACK WIRES AR2. E ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE LINE UP MOUNTING SCREWS WITH HOLES IN BACKPLATE AND SECURE WITH 2 BALL FINIALS SQUEEZE LEGS OF HARP SLIGHTLY TOGETHER AND THEN INSERT HARP ENDS INTO CUP PLACE THE SHADE ONTO HARP THEN SECURE WITH RUBBER WASHER AND FINIAL INSTALL A 100 WATT MAX MEDIUM BASE 3 WAY TYPE A BULB NOT INCLUDED INTO SOCKET RESTORE POWER AND TURN ON AT SWITCH YOUR NEW FIXTURE IS NOW READY FOR USE U 11 2012 213950RB INSTALLATION REMOVING THE POWER COORD WIRE CONNECTOR 2 PCS POWER CORD REMOVING THE POWER CORD THE POWER CORD IS THE WIRE THAT ENTERS THROUGH THE BOTTOM OF BACKPLATE 1 REMOVE THE 2 WIRE CONNECTORS THAT CONNECT TO POWER CORD BY TWISTING COUNTER CLOCKWISE SEE DIAGRAM 2 REMOVE THE CLIP AND PULL POWER CORD OUT THROUGH BOTTIOM OF BACKPLATE 3 FOLLOW OUTLET BOX INSTALLATION INSTRUCTIONS FOR WIRING TO AN OUTLET BOX 11 2012 21395ORB INSTRUCTIONS
3. MOD L 21595 PACKING DIAGRAM HANNEL AND 2 CORD COVERS BACKPLATE ASSEMBLY AND OTHER PARTS CA TITLE 2 Y HARP amp RUBBER WASHER NL n rO UBBER WASHER CORD COVER SHADE AVAILABLE PART IS SHADE 21395SHORB SHADE ANCHOR 21395SHORB 2 PCS REPLACEMENT PART SEREW 2 PCS ARP BACKPLATE MOUNTING BALL FINIAL Fi SWIVEL 2 PCS CHANNEL CORD COVER SCREWS 2 PCS WOOD SCREWS CORD COVER 2 PCS OWER CORD ASSEMBLY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS TOOLS YOU WILL NEED THE FOLLOWING TOOLS OR EQUIPMENT SCREWDRIVER AND DRILL UNPACK THE FIXTURE YOU SHOULD HAVE RECEIVED THE FOLLOWING PARTS IN THE PACKAGE FINIAL RUBBER WASHER SHADE HARP BACKPLATE ASSEMBLY 2 BALL FINIALS 2 CORD COVERS AND CHANNEL TO PROTECT THE FINISHES PLACE ALL PARTS ON A SOFT SURFACE MOUNTING HARDWARE PACKAGE GREEN GROUND SCREW 2 8 32 x 1 1 4 SCREWS WIRE CONNECTOR 4 PLASTIC ANCHORS AND 4 WOOD SCREVS NOTE IF USING POWER CORD FOLLOW INSTRUCTIONS BELOW IF WIRING TO AN OUTLET BOX PROCEED TO OUTLET BOX INSTALLATION INSTRUCTIONS IF FASTENING WITH ANCHOR TO DRYWALL 1 POSITION THE MOUNTING PLATE ON THE WALL AT DESIRED LOCATION AND MARK THE PLACE FOR THE ANCHORS TO BE INSTALLED 2 DRILL PILOT HOLES ON THE MARKED SPOTS AND INSERT PLASTIC ANCHORS IF FASTENING WITH WOOD SCREWS TO STUD IGNORE THIS STEP 3 ATTACH THE MOUNTING
4. PLATE TO THE ANCHORS OR THE SPOTS THAT YOU MARKED ON STUD AND SECURE WITH 2 WOOD SCREVWS 4 RAISE FIXTURE TO WALL LINE UP MOUNTING SCREWS WITH HOLES IN BACKPLATE AND SECURE WITH 2 BALL FINIALS 5 SQUEEZE LEGS OF HARP SLIGHTLY TOGETHER AND THEN INSERT HARP ENDS INTO CUP 6 PLACE THE SHADE ONTO HARP THEN SECURE WITH RUBBER WASHER AND FINIAL 7 INSTALL A 100 WATT MAX MEDIUM BASE 3 WAY TYPE A BULB NOT INCLUDED INTO SOCKET 8 TO INSTALL CORD COVER MOUNT CHANNEL ON THE WALL WITH SCREWS AND ANCHORS SEE ABOVE WITH CORD BEHIND COVERS PRESS CORD COVERS ONTO CHANNEL 9 PLUG THE POWER CORD INTO AN OUTLET AND TURN ON AT SWITCH 1172012 21395O0RB INSTRUCTIONS NL F UBBER WASHER SHADE AVAILABLE PART IS 21395SHORB SHADE SHADE 21395SHORB REPLACEMENT PART BLACK MOUNTING FIXTURE SCREW WIRE 2 PCS MOUNTING PLATE ARP BACKPLATE 8 32 x 1 1 4 SCREWS BALL FINIAL WIRE SWIVEL 2 PCS CONNECTOR 3 UP ARM BLACK 1 SUPPLY WIRE I WHITE SUPPLY WIRE SUPPLY GROUND WIRE FIXTURE GROUND WIRE OUTLET BOX OUTLET BOX INSTALLATION WHITE GREEN READ AND SAVE THESE INSTRUCTIONS FOSTUREWIPE GROUND SCREW WALL CAUTION TO AVOID POSSIBLE ELECTRIC SHOCK MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL IF YOU ARE REPLACING AN EXISTING FIXTURE FIRSTLY TURN THE FIXTURE OFF NEXT TURN THE WALL SWITCH OFF FINALLY GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME TURN THE FUSE
Download Pdf Manuals
Related Search