Kenroy Home 93425BRZ Instructions / Assembly
Contents
1. IP THE PLASTIC COVER OFF THE WIRE ABOUT 1 2 8 REMOVE 3 FINIALS FROM THE CUP BY UNSCREWING THE FINIALS STOP COMPLETE INSTALLATION INSTRUCTIONS ON NEXT PAGE BEFORE CONTINUING TO FINAL ASSEMBLY FINAL ASSEMBLY 1 INSTALL A 40 WATT MAXIMUM CANDELABRA BASE TYPE B BULB NOT INCLUDED INTO EACH SOCKET 2 PLACE THE GLASS SHADE TO BOTTOM OF THE CUP AND SECURE WITH 3 FINIALS REMOVED ABOVE 3 RESTORE POWER YOUR NEW FIXTURE IS NOW READY FOR USE 05 2014 93425BRZ ASSEMBLY INSTRUCTIONS SUPPLY GROUND WIRE OUTLET BOX WHITE SUPPLY WIRE WIRE CONNECTORS 3 PCS BLACK SUPPLY WIRE CEILING BLACK OR SMOOTIH FIXTURE WIRE WHITE OR RIBBED FIXTURE WIRE FIXTURE GROUND WIRE MOUNTING PLATE 8 32 SCREWS SUPPLIED WITH BOX umn KIYIIII l 8 32 x 1 SCREW GREEN GROUND SCREW ITHITHTITIEI ITUHTIHITVUEI CANOPY BALL FINIAL 2 PCS O SWIVEL EXTENSION TUBE INSTALLATION INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS CAUTION TO AVOID POSSIBLE ELECTRIC SHOCK MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL IF YOU ARE REPLACING AN EXISTING FIXTURE FIRSTLY TURN THE FIXTURE OFF NEXT TURN THE WALL SWITCH OFF FINALLY GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME TURN THE FUSE OR BREAKER TO THE OFF POSITION SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES F YOU ARE NO2. MODEL 95425BRZ PACKING DIAGRAM EXTENSION TUBE 4 PCS STYROFOAM 12 KGS LASS SHADE ASSEMBLY amp 3 FINIALS CANOPY ASSEMBLY AND OTHER PARTS SOCKET ASSEMBLY s STYROFOAM 12 KGS vo 93425BRZ BALL FINIAL 2 PCS ASSEMBLY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS READ INSTRUCTIONS ALL THE WAY THROUGH PRIOR TO ASSEMBLY THIS FIXTURE SHOULD TAKE APPROXIMATELY 5 MINUTES TO ASSEMBLE MAKE SURE ALL PARTS ARE FIRMLY TIGHTENED TOOLS YOU WILL NEED THE FOLLOWING TOOLS OR EQUIPMENT LADDER SCREWDRIVER ADJUSTABLE WRENCH WIRE CUTTERS UNPACK THE FIXTURE YOU SHOULD HAVE RECEIVED THE FOLLOWING PARTS IN THE PACKAGE CANOPY ASSEMBLY 3 EXTENSION TUBES CUP ASSEMBLY SOCKET ASSEMBLY AND GLASS SHADE TO PROTECT THE FINISH PLACE ALL PARTS ON A SOFT SURFACE MOUNTING HARDWARE PACKAGE 2 8 32 x 1 1 4 SCREWS AND 3 WIRE CONNECTORS FIXTURE ASSEMBLY 1 SCREW THE STEM TO BOTIOM OF THE CUP 2 REMOVE CROSS BAR FROM TOP OF THE CANOPY BY UNSCREWING 2 BALL FINIALS 3 FEED WIRE UP THROUGH EXTENSION TUBES AND WORKING UPWARDS TOWARD CANOPY AS SHOWN 4 SCREW EXTENSION TUBE TO TOP OF THE CUP USE ANY SINGLE LENGTH OF EXTENSION TUBE OR CONNECT TUBE SECTIONS TOGETHER TO OBTAIN DESIRED LENGTH 5 SCREW EXTENSION TUBE TO SWIVEL ON CANOPY 6 CUT OFF THE COBD TO KEEP THE COORD 6 FROM CENTER OF THE CANOPY 7 SPLIT THE END OF THE POWER SUPPLY WIRE 3 1 2 FROM THE END AND STR
3. T FAMILIAR WITH WIRING YOU SHOULD USE A QUALIFIED ELECTRICIAN THIS FIXTURE IS INTENDED TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE FIXTURE COMPLETE FIXTURE ASSEMBLY INSTRUCTIONS FIRST SEE PREVIOUS 1 ATTACH THE MOUNTING PLATE TO THE CEILING OUTLET BOX USING THE TWO SCREWS PROVIDED WITH THE OUTLET BOX NOTE IF THE SCREWS WITH THE OUTLET BOX ARE TOO SHORT USE THE 2 8 32 x 1 1 4 SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE 2 CONNECT THE WHITE OR RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTORS PROVIDED CONNECT THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE SAME MANNER INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE MOUNTING PLATE THEN CONNECT THE FIXTURE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTOR PROVIDED 3 TUCK THE WIRES CAREFULLY INSIDE THE OUTLET BOX SPREAD THE ELECTRICAL SPLICES SO THAT THE BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE 4 RAISE THE FIXTURE TO THE CEILING AND SECURE IN PLACE WITH 2 BALL FINIALS 58 SEE PREVIOUS PAGE FOR FINAL ASSEMBLY INSTRUCTIONS 05 2014 93425BRZ INSTALLATION
Download Pdf Manuals
Related Search