Kenroy Home 93313BS Installation Guide
Contents
1. TURN THE WALL SWITCH OFF FINALLY GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME TURN THE FUSE OR BREAKER TO THE OFF POSITION SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES IF YOU ARE NOT FAMILIAR WITH WIRING YOU SHOULD USE A QUALIFIED ELECTRICIAN THIS FIXTURE IS INTENDED TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE FIXTURE 1 ATTACH THE CROSS BAR TO THE CEILING OUTLET BOX USING THE TWO SCREWS PROVIDED WITH THE OUTLET BOX NOTE IF THE SCREWS WITH THE OUTLET BOX ARE TOO SHORT USE THE 2 8 32 x 1 1 4 SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE NEXT SCREW THE SCREW COLLAR LOOP ONTO THE NIPPLE AND THEN SCREW THE NIPPLE INTO THE CROSS BAR 2 SLIDE THE SCREW COLLAR NUT AND THEN THE CANOPY ONTO THE END OF THE CHAIN THEN FASTEN THE END LINK OF CHAIN TO THE SCREW COLLAR LOOP 3 INSERT THE FIXTURE WIRE AND THE GROUND WIRE UP THROUGH THE NIPPLE CONNECT THE WHITE OR RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTORS PROVIDED CONNECT THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE SAME MANNER INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE CROSSBAR THEN CONNECT THE FIXTURE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTOR PROVIDED 4 TUCK THE WIRES CAREFULLY INSIDE THE OUTLET BOX SPRE2. AD THE ELECTRICAL SPLICES SO THAT THE BLACK WIRES ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE NEXT RAISE THE CANOPY TO THE CEILING AND SECURE IN PLACE BY SCREWING THE SCREW COLLAR NUT ONTO THE SCREW COLLAR LOOP 5 SEE PREVIOUS PAGE FOR FINAL ASSEMBLY INSTRUCTIONS 12 2013 93313BS INSTALLATION
3. D ATTACH TO SCREW COLLAR LOOP ATTACH THE QUICK LINK TO END LINK OF THE CHAIN AND ATTACH THE QUICK LINK TO CHAIN LOOP AND THEN SECURE WITH SMALL NUT THREAD FIXTURE WIRE AND GROUND WIRE UP THROUGH EVERY OTHER LINK OF CHAIN TO SPREAD A LINK OF CHAIN USE A PAIR OF PLIERS AND A SCREWDRIVER AS SHOWN ABOVE BEING CAREFUL TO WRAP THE JAWS OF THE PLIERS WITH CLOTH TO PROTECT THE FINISH OF THE CHAIN STOP COMPLETE INSTALLATION INSTRUCTIONS ON NEXT PAGE BEFORE CONTINUING TO FINAL ASSEMBLY FINAL ASSEMBLY 1 INSTALL A 60 WATT MAX MEDIUM BASE TYPE A BULB NOT INCLUDED INTO EACH SOCKET 2 SLIDE SMALL METAL WASHER DIFFUSER LARGE METAL WASHER OVER THE NIPPLE OF STEM AND SECURE WITH THE FINIAL 3 RESTORE POWER YOUR FIXTURE IS NOW READY FOR USE 93313BS ASSEMBLY INSTRUCTIONS SUPPLY GROUND WIRE OUTLET BOX WHITE BLACK SUPPLY WIRE SUPPLY WIRE CEILIN WIRE 5 BLACK OR 3 PCS FIXTURE WIRE WHITE OR RIBBED 8 52 SCREWS FIXTURE SUPPLIED WITH BOX E E ROSSBAR IXTURE GROUND WIRE CANOPY REEN GROUND SCREW SCREW COLLAR NUT SCREW COLLAR LOOP lt amp INSTALLATION 5 READ 5 THESE 5 5 CAUTION TO AVOID POSSIBLE ELECTRIC SHOCK MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL IF YOU ARE REPLACING AN EXISTING FIXTURE FIRSTLY TURN THE FIXTURE OFF NEXT
4. MODEL 9551585 PACKING DIAGRAM ANOPY CHAIN QUICK LINK AND OTHER PARTS POLE ASSEMBLY WIRE CONNECTOR 3 PGS IPPLE CREW COLLAR NUT SCREW COLLAR LOOP HAIN LOOP ASSEMBLY SHADE 3313SHBS REPLACEMENT PART IFFUSER SMALL METAL WASHER LARGE METAL WASHER gt FF NIAL AVAILABLE PART 15 93313SHBS SHADE 12 2013 95515 5 ASSEMBLY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS READ INSTRUCTIONS ALL THE WAY THROUGH PRIOR TO ASSEMBLY THIS FIXTURE SHOULD TAKE APPROXIMATELY 10 MINUTES TO ASSEMBLE MAKE SURE ALL PARTS ARE FIRMLY TIGHTENED TOOLS YOU WILL NEED THE FOLLOWING TOOLS OR EQUIPMENT LADDER SCREWDRIVER ADJUSTABLE WRENCH WIRE 5 AND PLIERS UNPACK THE FIXTURE YOU SHOULD HAVE THE FOLLOWING PARTS IN THE PACKAGE CANOPY CHAIN QUICK LINK POLE ASSEMBLY COLUMN SHADE SOCKET ASSEMBLY DIFFUSER 2 METAL WASHERS AND FINIAL TO PROTECT THE FINISH PLACE ALL PARTS ON A SOFT SURFACE MOUNTING HARDWARE PACKAGE SCREW COLLAR LOOP SCREW COLLAR NUT NUT NIPPLE 2 8 32 X 1 1 4 SCREWS CROSSBAR GREEN GROUND SCREW AND 3 WIRE CONNECTORS FIXTURE ASSEMBLY 1 PLACE THE SHADE COLUMN OVER THE NIPPLE ON TOP OF THE SOCKET ASSEMBLY AND ROTATE THE POLE ASSEMBLY TO SECURE 2 DETERMINE THE LENGTH OF CHAIN REQUIRED TO HANG THE FIXTURE AT THE DESIRE HEIGHT REMOVE OR ADD CHAIN AS DESIRED USING PLIERS OPEN ONE END LINK OF CHAIN AN
Download Pdf Manuals
Related Search