TroposAir 88701 Instructions / Assembly
Contents
1. Owner s Manua This instruction contains 5 pages Page 1 Foreword Page 2 Unpack and inspect parts contained Page 3 Notes before installation and Hanging system installation Page 4 Wire connection and Canopy installation Page 5 Blade and Pull Chain Knob installation ames Net weight UL 9 0 KGS ENERGY STAR PARTNER 19 8 LBS Toll Free 1 855 676 7247 WARNING Read and follow these instructions carefully and be mindful of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 1 To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning 2 To avoid possible electric shock be sure electricity is turned off at the main power box before wiring All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections 3 Make sure that your installation site will not allow rotating fan blades to come in contact with any object Blades should be at least 7 feet from floor when fan is in ope2. Pull Chain Knob provided from hardware bag to the pull chain from switch housing Canvas Blade Switch Housing Bottom end Post Hole Eyelet of NEXT Blade Frame Important Spring hook must connect the Post Hole of NEXT blade frame or the Canvas blade will not be flat 5 Turn on the power at breaker box your fan is ready for operation Pull Chain Knob gt P5
3. and Yoke Remove cross pin and cotter pin from downrod Insert downrod through canopy and yoke cover and feed motor lead wires through downrod Loosen 2 downrod jam screws at yoke Insert downrod assembly into yoke Insert the cross pin through yoke amp downrod and secure with cotter pin Tighten both downrod jam screws to further secure downrod Pull down the yoke cover to cover yoke 8 Downrod cross Pin Cotter Ping e Canopy 4 Downrod Jam Screw 2 Loosening Screw 2 Yoke cover pL 0 SSS Tightening Ajquessy 1C Hanging the fan Lift fan assembly onto mounting bracket Rotate fan so that the groove on the ball engages the ridge in the mounting bracket Mounting Mounting Bracket Fan Assembly ee Ball Groove cess 5 Se R 2 WIRE CONNECTION Making electrical wire connection Follow diagram below and make sure that all exposed wires are secured inside wire nuts or terminal block Note Wires from house may vary in color and may not include ground wire green White wire from house to white wire from fan Black wire from house to black wire and blue wire from fan Ground wire from house to green wire from downrod and from mounting bracket Secure with twist lock wire nuts Included After wiring is completed gently push wires into junction box with wire nuts pointing upward From House From Fan Outlet Box Wire Form House White MM White MOT
4. OR N Black EEE ii q Black MOTOR L cia Blue for light kit Green Green for ground wire from downrod Green from mounting bracket Secure with twist lock wire nuts Note Two screws are pre installed on mounting bracket for canopy installation Push up canopy until two screws pre screwed on mounting bracket are engaged with two key holes on canopy Rotate canopy slightly until two pre installed screw heads are engaged in the narrow end of key holes Tighten both screws Key Hole 2 P4 4 BLADE INSTALLATION 4A Attach canvas blades onto blade frames 4B Attach blade assembly to motor Connect spring hooks 6 from blade frame to Remove 3 motor stoppers by removing screws relative eyelets on canvas blade _ Secure Blade Assembly to the motor with Note Leave those two eyelets of Tip and 2 motor screws provided from hardware bag Bottom ends for Step 4C Spring Hook 6 Blade Frame oe 6 any 1N 2 of A N of x S Motor n Stoppers 3 A 8 8 t Motor Screws 4C Hook up TIP end and BOTTOM end amp Pull Chain Knob installation TIP end Connect Hole from tip end of blade frame to tip end eyelet of canvas with spring hook provided from hardware bag BOTTOM end Connect bottom end eyelet of canvas to the post hole of next blade frame with spring hook provided from hardware bag Connect
5. ings are adequately charged with grease so that under normal conditions further lubrication should not be necessary 10 The fan must be turned off and stopped before reversing fan direction 11 This fan is suitable for slope ceiling 12 This fan is reversible 13 This fan is light kit adaptable 14 This fan is remote adaptable 15 This fan is suitable for damp location use P1 Unpack and inspect fan carefully to be certain all contents are included Mounting Bracket Downrod Assembly P2 Hardware Bag For Mounting Bracket FlatWasherx2 Spring Washer x2 0 Q Machine Screw x2 Wood Screw x2 For Wire Connection Wire Nut x 3 4a 4a For Blade Installation Blade Screw x 9 one spare screw included O Ck Ck Ck CK Ck Ck Cre Spring Hook x 9 one spare hook included A AA For Fan Pull chain knob x1 Blade Frame 4 WARNING blades should be at least 7 feet from floor Note 1 Note 2 Turn off power at breaker Use metal outlet box suitable box to avoid possible for fan support electrical shock Outlet box must support 35 Ibs min 1A Installing mounting bracket to ceiling outlet box Install mounting bracket to outlet box in ceiling by using screws included with the outlet box and washers from the hardware bag Outlet Box Mounting Bracket 1B Installing Downrod
6. ration 4 4 If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight of the moving fan If the fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel 5 Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets 6 After making electrical connections spliced conductors should be turned upward and pushed carefully up into outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and the HOT wires on the other side 7 Electrical diagrams are for reference only Light kits that are not packed with the fan must be UL ETL listed and should be installed per the light kit s installation instructions 8 After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury 9 The fan can be made to work immediately after installation The bear
Download Pdf Manuals
Related Search