Hampton Bay N2003 Installation Guide
Contents
1. ASSEMBLY 81 13 Chain 12 Loop Lock 7 Loop m 6 Metal Pad A 5 Cap 4 Tube kK 9 Screw ST 8 Shade i 10 Candle Tube 2 Nipple 3 Hex Nut Light Bulb i 1 Main Fixture Body PARTS INCLUDED FOR INSTALLATION parts are not to scale TA 2 ea Loop Locks l ea 5 feet Chain 13 ea Canopy Washer 1 ea Canopy Cover 15 1 ea Top Loop 12 14 16 S coy W 2 ea Hex Nuts 2 ea Lock 1 ea All Thread Rod 1 ea Mounting Strap 2 ea Mounting 3 ea Wire Connectors 17 Washers 18 19 20 Screws 21 22 INSTALLATION INSTRUCTIONS 1 Using a Phillips Screwdriver securely fasten the Mounting Strap 20 to the Outlet Box using the two Mounting screws 21 provided 2 Adjust the Chain 13 to the desired height by lifting the fixture and attaching the Loop Lock 12 to a link of Chain 13 closer to the ceiling The fixture can be raised and lowered in this manner until the desired height 1s achieved Next use pliers to twist open cover the chain with cloth to prevent damage the first unused link of Chain 13 Remove and save the excess chain Pull the excess fixture wires through the All Thread Rod 19 and into the Outlet Box Wires may be left at full length or shortened determined by the amount of space in the Outlet Box to make wire connections 3 Connect the fixt2. alterations neglect or mishandling This warranty shall not apply to any product that is found to have been improperly installed set up or used in any way not in accordance with the instructions supplied with the product This warranty shall not apply to a failure of the product as a result of an accident misuse abuse negligence alteration or faulty installation or any other failure not relating to faulty material or workmanship This warranty shall not apply to the finish on any portion of the product such as surface and or weathering as this is considered normal wear and tear The manufacturer does not warrant and specially disclaims any warranty whether expressed or implied of fitness for a particular purpose other than the warranty contained herein The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage including but not limited to any labor expense costs involved in the replacement or repair of said product
3. INSTRUCTIONS MANUAL 4 Light Pendant Menlo Park Collection HOME DEPOT SKU N2003 UPC 887016005812 Brushed Nickel Finish Thank you for purchasing this Hampton Bay interior four light pendant This product has been manufactured with the highest standards of safety and guality FEATURES 1 Easy to install 2 Standard 72 inch wire and 60 inch chain for open entry way and cathedral ceiling installations Also includes one Loop Lock to easily adjust length of chain QUESTIONS PROBLEMS MISSING PARTS Before returning to your local Home Depot please call our Customer Service Team at 1 877 527 0313 or visit www homedepot com Please reference your SKU N2003 or UPC 887016005812 WARNING BECAUSE FAILURE TO COMPLY CAN LEAD TO INJURY 1 Before starting installation of this fixture or removal of a previous fixture disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box 2 CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS 2 3 If you have any non electrical questions about this fixture please call our Customer Service Team at 1 877 527 0313 or visit www homedepot com Please reference your SKU N2003 or UPC 887016005812 4 KEEP your receipt and these Instructions for Proof of Purchase TOOLS REQUIRED FOR INSTALLATION AND ASSEMBLY not included Phillips Flathead Wire Wire Screwdriver Screwdriver Cutters Strippers Light Bulb x4 Safety Gog
4. gles Electrical Tape 60 watt maximum A M Pliers Gloves Ladder PARTS INCLUDED FOR ASSEMBLY parts are not to scale i S5 ea Hex ea Tube leaCap 1 ea Metal Pad 1 ea Main Fixture Body 1 1 ea Nipple 2 Nut 3 4 5 6 i 8 1 ea Loop 1 ea Shade 4 ea Screws 4 ea Candle lea L Phillips 7 8 9 Tubes 10 Screwdriver 11 ASSEMBLY INSTRUCTIONS 1 Carefully unpack the fixture Lay out all parts on a clean surface 2 Screw the Nipple 2 into the coupling on the Main Fixture Body 1 and secure it with a Hex Nut 3 Slide the Tube 4 onto the Nipple 2 3 Adjust the fixture wire into the slot of the notched pad on the Shade 8 making sure the wire feeds through the Shade 8 Slide the Shade 8 onto the Tube 4 Fig 1 4 The Shade 8 should be fastened into the Tube 4 and secured with Screws 9 using a Phillips Screwdriver 11 as show Fig 2 5 Attach the Cap 5 and the Metal Pad 6 onto the Tube 4 and Thread the Loop 7 onto the Nipple 2 6 Attach the Candle Tubes 10 into the socket on the Main Fixture Body 1 as shown 7 Weave the fixture wires through the Chain 13 every 4th to 5th loop Loop Lock 12 Canopy Washer 14 Top Loop 16 All Thread Rod 19 and Canopy Cover 15 8 Screw the Mounting Strap 20 to the All Thread Rod 19 and secure using a Lock Washer 18 and Hex Nut 17
5. rrective Action Light will not turn on 1 Power 1s off 1 Make sure power supply is on 2 Faulty switch 2 Test or replace switch 3 Faulty wire connection 3 Check wiring Fuse blows or circuit breaker Crossed wires or power wire is grounding Check wire connections trips when light is turned on out PRODUCT MAINTENANCE 1 To clean the outside of the fixture use a dry or slightly dampened clean cloth use clean water never a solvent to wipe the surface of the fixture 2 To clean the inside of the fixture first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box Next use a dry or slightly dampened clean cloth use clean water never a solvent to wipe the interior surface of the fixture 3 Do not use any cleaners with chemicals solvents or harsh abrasives Use only a dry soft cloth to dust or wipe carefully LIMITED WARRANTY The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five 5 years from date of purchase This warranty applies only to the original consumer purchaser and only to products used in normal use and service If this product is found to be defective the manufacturer s only obligation and your exclusive remedy is the repair or replacement of the product at the manufacturer s discretion provided that the product has not been damaged through misuse abuse accident modifications
6. ure wire A1 without writing on it raised ribs to the white neutral wire from the Outlet Box A and the fixture wire B1 with writing on it to the black hot wire from the Outlet Box B Cover the wire connections using the Wire Connectors 22 Wrap the two wire connections with electrical tape for a more secure connection Connect the copper ground wire C1 from the fixture to the Outlet Box ground wire C If a ground wire does not exist in the Outlet Box connect the fixture ground wire directly to the Ground Screw on the Mounting Strap 20 Note Consult your local electrical code for approved grounding methods Tuck all wires back into the Outlet Box 4 Slide the Canopy Cover 15 into place and secure to the ceiling using the Canopy Washer 14 5 Install light bulbs not provided in accordance with the fixture specifications DO NOT EXCEED THE MAXIMUM WATTAGE RATING FOR THIS FIXTURE 6 Installation 1s complete Turn on power at the circuit breaker or fuse box Turn the light switch on to activate the fixture 6 INSTALLATION 17 Hex Nut 21 Mounting Screw 18 Lock Washer 20 Mounting Strap Ground Screw 18 Lock Washer 19 All Thread Rod 17 Hex Nut 16 Top Loop 5 T 1 gt 15 Canopy Cover es 414 Canopy Washer T 412 Loop Lock 1 1 13 Chai ain J 224 mx B1 A E 37 412 Loop Lock un 7 Loop TROUBLESHOOTING II l Possible Cause Co
Download Pdf Manuals
Related Search