Lithonia Lighting IBH 11L MV Installation Guide
Contents
1. CHAIN KIT ND ra B POWER WIRES BLK WHT A HULES UN SIDE OF CHN ARE WRAPPED ARUUND THE ACCESS PLATE SECTION 2 SERVICING IBH 12L SHOWN 1 2 3 4 5 6 7 8 9 Disconnect all power to the IBH high bay being service To access the driver remove the two screws at the ends opposite the safety cable side Rotate top driver housing to its side and remove the two screws holding the channel cover FIGURE 2A Rotate the led housing to its side if hanging by the top channel SEE FIGURE 2B Slide the channel cover off its securing clips SEE FIGURE 2 Install new driver if needed in the same location Make sure the new driver has same electrical specifications as the old driver Mark all wiring before remove the old driver Make sure to install the EMI ferrite core onto the power leads of the new driver If present in your assembly Use only UL listed components wiring and connectors When service is done make sure to push all led wiring back into the driver housing before rotating the driver housing to closed position SEE FIGURE 2A and FIGURE 2B Do not let wiring get caught outside the two assemblies 10 To clean lens remove one bottom end cover and slide lens out NOTE LED housing is made from aluminu2. E eB Y TOP CHANNEL E USING DRIVER H XX SING ASSEMBLY M END COVER 3 8 PHILLIPS HD SCREW SECURED BY 6 SCREWS 2X PER END HILLIPS DRIVER TO REMOVE AND INSTALL SCREWS ONLY m WY T l C Five year limited warranty Warranty terms are located at U459430 REV F www acuitybrands com customerresources term and conditions aspx Page 4of 4
3. SS cuitybr ands LED IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION e To reduce the risk of death personal injury or property damage from fire electric shock falling parts cuts abrasions and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels e Before installing servicing or performing routine maintenance upon this equipment follow these general precautions e Installation and service of luminaires should be performed by a qualified licensed electrician e Maintenance of the luminaires should be performed by person s familiar with the luminaires construction and operation and any hazards involved Regular fixture maintenance programs are recommended e It will occasionally be necessary to clean the outside of the refractor lens Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user Refractor lens should be washed in a solution of warm water and any mild non abrasive household detergent rinsed with clean water and wiped dry Should optical assembly become dirty on the inside wipe refractor lens and clean in above manner replacing damaged gaskets as necessary e DO NOT INSTALL DAMAGED PRODUCT This luminaire has been properly packed so that no parts should have been damaged during transit Inspect to confirm Any part damag
4. ed or broken during or after assembly should be replaced e Recycle For information on how to recycle LED electronic products please visit www epa gov e These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation operation or maintenance Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser s or owner s purposes this matter should be referred to Acuity Brands Lighting Inc WARNING WARNING RISK OF ELECTRIC SHOCK RISK OF BURN Y Disconnect or turn off power before v Allow lamp fixture to cool before handling installation or servicing Do not touch enclosure or light source v Verify that supply voltage is correct by Y Do not exceed maximum wattage marked on comparing it with the luminaire label luminaire label information v Follow all manufacturer s warnings Make all electrical and grounded recommendations and restrictions for driver connections in accordance with the National type burning position mounting Electrical Code NEC and any applicable locations methods replacement and local code requirements recycling All wiring connections should be capped with UL approved recognized wire connectors CAUTION CAUTION RISK OF INJURY RISK OF FIRE v Wear gloves and safety glasses at all times Y Keep combustible and other materials that when removing lumina
5. ire from carton can burn away from lamp lens installing servicing or performing Y Do not operate in close proximity to persons maintenance combustible materials or substances Avoid direct eye exposure to the light source affected by heat or drying while it is on Page 1of 4 SS cuityBr ands LED IMPORTANT SAFETY INSTRUCTIONS Lighting i CAUTION RISK OF PRODUCT DAMAGE Never connect components under load Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation Unless individual product specifications deem otherwise Never connect an LED product directly to a dimmer packs occupancy sensors timing devices or other related control devices LED fixtures must be powered directly off a switched circuit Unless individual product specifications deem otherwise Do not restrict fixture ventilation Allow for some volume of airspace around fixture Avoid covering LED fixtures with insulation foam or other material that will prevent convection or conduction cooling Unless individual product specifications deem otherwise Do not exceed fixtures maximum ambient temperature Only use fixture in its intended location LED products are Polarity Sensitive Ensure proper Polarity before installation Electrostatic Discharge ESD ESD can damage LED fixtures Personal grounding equipment must be worn during all installation or servicing of the unit Do not touch individual electrical com
6. m sheets Do not over tighten screws when re installing the end cover Use hand held screw driver ONLY to remove and install screws 11 Slide lens out slowly and clean both sides of lens Clean lens will ensure optimal light output SEE FIGURE 3 12 Reinstall the lens and end cover when cleaning is done Gloss side of lens faces floor 13 Maintenance of the luminaires should be performed by person s familiar with the luminaires construction and operation and any hazards involved Regular fixture maintenance programs are recommended for optimal light output Page 3 of 4 cuitybr ands LED IMPORTANT SAFETY INSTRUCTIONS Lighting x WIRE WAY 7 TAS SIDE HAS l A v SAFETY CABLE IBH 12L SHOWN g KL SKE DRIVER IBH 24L IS TWICE AS LONG if SS RIVER HOUSING OPEN POSITI SERVICING CONCEPT IS i Sc Sa ALMOST IDENTICAL SCREW ACCESS PLATE WIRING INT HE DRIVER RE ROTATING THE DRIVER HOUS TH CLOSED POSITION REMOVE THIS SCREW BOTH ENDS OF FIXTURE FIXTURE HUNG BY font N J C dS 2 ABI LIP PPTIONAL CABLE KIT y A NAL CHAIN KIT BUTH SIDES
7. or commercial use 1 Disconnect all power to the existing luminaire and remove the existing luminaire from the ceiling Inspect the existing mounting location for damage before install the new IBH LED high bay in this location 2 Remove the new LED fixture from packaging and inspect for any damages Handle new LED fixture with care If damaged do not use call your local rep for replacement 3 CHAIN MOUNT EXAMPLE Install the chain into the provided wire hanger Secure the other end of the chain to a structure using hardware rated for the load Install the wire hanger onto the side of the top IBH LED channel Contact factory or agency concerning areas that have high vibration or over head cranes and or high velocity SEE FIGURE 1 A Make sure the wiring hangers are fully engaged into the side holes on the top channel If using S hooks make sure all loops are crimped closed 4 Connect the LED high bay wiring to line wire black to black white to white and green to green Use only UL listed wiring connectors 105C or greater and UL listed wiring 105C or greater Use only UL listed cords NOTE Purple and gray lead inside the driver compartment are 0 10V low voltage dimming leads Connect to dimming low voltage wiring only 5 Clean all residues fingerprints from the new LED high bay and lens Double check all hanging hardware before moving onto the next installation 0 OPTIONAL CHAIN KIT
8. ponents as this can cause ESD shorten lamp life or alter performance Some components inside the fixture may not be serviceable In the unlikely event your unit may require service stop using the unit immediately and contact an ABL representative for assistance Always read the fixtures complete installation instructions prior to installation for any additional fixture specific warnings Please see product specific installation instructions for additional warnings or any applicable FCC or other regulatory statements Failure to follow any of these instructions could void product warranties For a complete listing of product Terms and Conditions please visit www acuitybrands com Our Brands Indoor Outdoor Indoor Lighting Outdoor Lighting Controls Daylighting Lithonia Lighting Gotham American Electric Lighting DARK TO LIGHT SunOptics Carandini Mark Architectural Lighting Antique Street Lamps LC amp D Holophane Peerless Hydrel ROAM RELOC Renaissance Lighting Tersen Sensor Switch Light Concepts Winona Lighting Synergy Acuity Brands Lighting Inc assumes no responsibility for claims arising out of improper or careless installation or handling of its products ABL LED General Warnings Form No 503 203 2010 Acuity Brands Lighting Inc All rights reserved 12 01 10 Page 2 of 4 SS cuityBr ands LED IMPORTANT SAFETY INSTRUCTIONS Lighting SECTION 1 INSTALLATION IBH LED 2FT length shown Note current IBH LED is only setup f
Download Pdf Manuals
Related Search