Worldwide Lighting W33011G20 Installation Guide
Contents
1. WAY VAN AZZ SK WY wx WAVY av WARNING CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please excersise extreme Caution during unpacking and installation WARNING 1 After passing the main eiectrical wire through the 10mm pipe and connecting the pipe to the main body top connector place all remaining pieces as shown in nurmerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts The part Numbers coincide CAUTION 1 Rated 110v 130v 60Hz bulb GU10 35W maximum 2 Care Should be taken to avoid damage to the surface of lighting and wire wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to live wire and white or blue wire to neutral wire and double colored or bare copper wire to ground wire 4 Never install lighting on damp ceiling the room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas clean the lighting with Clean soft cloth only 6 Installation must be carried out by qualified electrician only 7 Disconnect the power before installing Ceaning and replacing lighting 8 Never cover the lighting when power is connected 9 Firmness must be secured when installing ceiling tube chain pipe and other connecting parts 10 Care should be taken to avoid damage when installing glass parts2. 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code and the appropriate local electrical codes Make sure that the elecrtrical supply to the chandellier is turned off at the main fuse or circuit breaker before doing any installation Elegant lighting shall not be responsible for unprofessional wiring Frame Assembly Instructions Installation Please read all instructions carefully Before you proceed to install make sure that the power supply is turned off and remains off until installation is complete please note that each part has been assigned a number please proceed in a numerical order 1 Fix the crossbar 02 with chain 01 or junction box 2 Fix the lamp body 03 on the crossbar 02 with crossbar bracket 04 3 Make sure the positive and negative charges of wire and lamp body match correctly screw the connect point with the junction cap 4 Make sure the main wire is enough long and keep the rest wire in the 4 J box 5 As the crystal pressing instruction hang the crystal parts The end
3. W 33011020 D20 H10 L10 s i ii 7 f s b i ie o ANA y 5 i k D ao ni D Ay oe me tes SN Lap P r A ae SA orbs oe ga Sip kir POA p E q ik me T 7 We are dedicated to providing the finest quality crystal chandelier for our customers Our master craftsmen and designer pride themselves on their attention to detail Prompt efficient service is our priority Enclosed are detailed instructions on how to properly install your chandelier Please read all instructions carefully and thoroughly lf you have any questions please fell free to call our toll free CHANDELIER HOTLINE AT 1 855 411 8999 GQ Crystal Dressing Instructions CANOPY PARTS LIST W33011C20 oe cn sss a ae to wear either rubber or cotton gloves So as to prevent any Existing Electrical Box damage or smudging on the crystals Crossbar Crossbar Screws x 2 not srpplied ee Metal plate Wire Connector Shrinkable tube 14mmX 3 40mmX 1 Cable tie gt A 144 STRINGS oS 10mmX 11 B 84 STRINGS Ground Wire C 91 STRINGS CANOPY INSTALLATION DIAGRAM Frame Parts List i 03 Metal Finial 01 Crossbar 02 Lamp Body WARNING CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please excersise extreme Caution during unpacking and installation WARNING After passing the main eiectrical wire through the 10mm pipe a
4. hting shall not be responsible for unprofessional wiring Crystal Dressing Diagram When dressing the chandelier with the crystals please remember to wear either rubber or cotton gloves So as to prevent any damage or smudging on the crystals NV V 4 A AN PAAA WNN CEY WAI ANN ARN ANSON L NVV SA AN l ASAN WANNY Ww ANNON AN M E LX ANN WO NANANA M N AN i ANN ZNA NI V V V V A TAVAT 4 WN AN AN ANNIN TVA WAL LAN ASAA WY N WOW VW ININ FRR UAV AV AN WOW C V 4 is A SDAS AN VANS AKAN AN 5 TR MANS VAA ZAAS WAAAY CEY NINININN WOW g WOOLY 7 Frame Assembly Diagragram CANOPY INSTALLATION INSTRUCTIONS Please read all instructions carefuly Before you proceed to install make sure that the power supply is turned off and off until installation is complete Please note that each part has been asigned a letter Please proceed in an alphabetical order A Existing Electrical Box B Crossbar C Crossbar Screws D Metal Plate E Crossbar Bracket F Neutral Conductor G Hot Wire H Junction Caps I Ground Wire J Wire Attach the Crossbar B to the existing electrical box A using 1 7 va S A a YA A MANNA AA N A AN ANIONS the two crossbar screws E which are not supplied and should W V LOR A Y hor MALY CY AYN AS N AA ENN SY already be in your box wv av WAAMA ANSAN l l AADA WAAAY LAW AOSA AN AA AKA L AAW LEAN A ASANA WAAAY w WAZ VV AN WANNAN Way VVVVV AAAA WAAAY
5. nd connecting the pipe to the main body top connector place all remaining pieces as shown in nurmerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts The part Numbers coincide CAUTION 1 Rated 110v 130v 60Hz bulb GU10 35W maximum 2 Care Should be taken to avoid damage to the surface of lighting and wire wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to live wire and white or blue wire to neutral wire and double colored or bare copper wire to ground wire 4 Never install lighting on damp ceiling the room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas clean the lighting with Clean soft cloth only 6 Installation must be carried out by qualified electrician only 7 Disconnect the power before installing Ceaning and replacing lighting 8 Never cover the lighting when power is connected 9 Firmness must be secured when installing ceiling tube chain pipe and other connecting parts 10 Care should be taken to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code and the appropriate local electrical codes Make sure that the elecrtrical supply to the chandellier is turned off at the main fuse or circuit breaker before doing any installation Elegant lig
Download Pdf Manuals
Related Search