Worldwide Lighting W83109C26-CL Instructions / Assembly
Contents
1. W 83109C26 CL D26 H24 L6 We are dedicated to providing the finest quality of crystal chandeliers for our customers Our master craftsman and designers pay their full attention to detail prompt and efficient service Enclosed are detailed instructions on how to properly install your chandelier Please read all instructions thoroughly If you have any questions please feel free to call our toll free chandelier hotline at 1 859 411 8999 C US Crystal Dressing Instructions W83109C26 1 4mmX 1 When dressing the chandelier with the crystals please remember to wear either rubber or cotton gloves So as to prevent any damage or smudging on the crystals 14mmX3 HEA Co este 14mmX8 00600 40mmX1 We CANOPY PARTS LIST Existing Electrical Box Crossbar Screws Crossbar Screws x 2 not srpplied Canopy Chains Gonna Glass Bowl LD Glass crafts Wire Connector w Shrinkable tube Cable tie Ground Wire our CANOPY INSTALLATION DIAGRAM Frame Parts List 02 Crossbar ESIS PP REI va 03 Canopy Goorin 04 Chains SSSI ROOK ES es I 05 Glass Bowl WARNING Crystal Dressing Diagram CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please have extreme caution when unpacking and installing When dressing the chandelier WARNING with the crystals please remember to wear either rubbe2. chandelier is turned off at the main fuse or circuit breaker before doing any installation Worldwide lighting is not responsible for unprofessional wiring Frame Assembly Diagragram CANOPY INSTALLATION INSTRUCTIONS Please read all instructions carefuly Before you proceed to install make sure that the power supply is turned off and off until installation is complete Please note that each part has been asigned a letter Please proceed in an alphabetical order A Existing Electrical Box B Crossbar C Crossbar Screws D Metal Plate E Crossbar Bracket F Neutral Conductor G Hot Wire H Junction Caps I Ground Wire J Wire gt 27 A ESS KX SS Attach the Crossbar B to the existing electrical box A using the two crossbar screws E which are not supplied and should already be in your box S Z 525 A a WARNING Frame Assembly Instructions CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please have extreme caution when unpacking and installing Installation Please read all instructions carefully Before you proceed to install make sure that the power supply is turned off and WARNING remains off until installation is complete Dr nr please note that each part has been assigned a number After passing the main electrical wire through the 10mm pipe and please proceed in a numerical order connecting the p
3. ipe to the top main body connector place all remaining pieces as shown in numerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts CAUTION Rated 110v 130v 60Hz bulb E12 40W maximum Take care to avoid damage to the surface of lighting and Assembly Lamp Body 01 f vire Woaring gloves d recommended when installing Install Crossbar with J Box and then Fixed the Canopy 03 Connect black or red wire of the lighting to the white or 2 Join the Lamp Body 01 and crossbar 02 with Chains 04 blue wire Then connect to the neutral wire and double colored Make sure the positive and negative charges of wire and or bare copper wire to the ground wire Lamp Body 02 match correctly screw the connect point ever install lighting on damp ceiling The room should be with the Junction cabe dry and well ventilated Make sure the main wire is enough long and keep the rest Keep lighting away from acid alkali and other corrosive wire in the 4 J box f chemical or gas Clean with soft cloth only As the crystal pressing instruction hang the crystal Installation must be carried out by qualified electrician parts only Install lighting Source Disconnect the power before installing cleaning or replacing the lamp Never cover the lighting when power is connected Fixture must be secured when installing the ceiling tube chain pipe and other connecting parts 10 Take care t
4. o avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code It must be in the appropriate local electrical codes Make sure that the electrical supply to the chandelier is turned off at the main fuse or circuit breaker before doing any installation Worldwide lighting is not responsible for unprofessional wiring
5. r or cotton i g gloves So as to prevent any After passing the main electrical wire through the 10mm pipe and damage Or st deine o the crystals connecting the pipe to the top main body connector place all remaining pieces as shown in numerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts CAUTION Rated 110v 130v 60Hz bulb E12 40W maximum 2 Take care to avoid damage to the surface of lighting and wire Wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to the white or blue wire Then connect to the neutral wire and double colored or bare copper wire to the ground wire 4 Never install lighting on damp ceiling The room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas Clean with soft cloth only 6 Installation must be carried out by qualified electrician only a Disconnect the power before installing cleaning or replacing the lamp 8 Never cover the lighting when power is connected 9 Fixture must be secured when installing the ceiling tube chain pipe and other connecting parts 10 Take care to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code It must be in the appropriate local electrical codes Make sure that the electrical supply to the
Download Pdf Manuals
Related Search