Home
Sea Gull Lighting 6039-12 Installation Guide
Contents
1. chain S and connect it to the fixture loop J at the top of the fixture STEP 6 Slide the screw collar ring F and canopy G in that order over chain H Open one link on the other end of the chain H and attach it to the screw collar E which has been mounted to the ceiling nipple C BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY STEP 7 Lace wires up through chain H and pass wires through holes in screw collar E We recommend lacing wire up through every other link of chain H STEP 8 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below i 4 GROUP A GROUP B CONNECT TO BLACK HOUSE WIRE CONNECT TO WHITE HOUSE WIRE BLACK PARALLEL WIRE SQUARE amp RIDGED Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector clockwise until you feel a firm resistance D Gently try to remove the wires from the connector If you can remove the wires carefully re do steps B and C as above and chec
2. Installation And Safety Instructions Sea Gull Lighting Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM IMPORTANT SAFETY INSTRUCTIONS e Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off Use of other manufacturers components will void warranty listing and create a potential safety hazard e You don t need special tools to install this fixture e Be sure to follow the steps in the order given e Read instructions carefully e If you are unclear as to how to proceed contact a qualified electrician Save these instructions NOTE This glass is handcrafted the slight imperfections in the glass add to the authenticity of the fixture WIRE CLEANING CONNECTORS To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders GREEN steel wool or abrasive paper GROUNDING SCREW D ORDERING PARTS NIPPLE C Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when fe x jos oO Q xe tet 5 v BEFORE YOU BEGIN Carefully remove the fixture from the carton and chec
3. k again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire M from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire M from the fixture if supplied and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors After wires are connected tuck them carefully inside outlet box Raise canopy H against ceiling and thread the screw collar ring G to the screw collar E Install lamps not supplied
4. k that all parts are included as shown in Figure 1 Be careful not to misplace any of the screws or parts which are needed to install this fixture NIPPLE J IF APPLICABLE TO REMOVE THE PACKAGING 1 Remove the 3 retaining screws and remove the cage 2 Remove the cardboard packaging ASSEMBLY Carefully remove the fixture from the carton and check that all parts are included as shown in figure 1 and 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture o D D jes D O lo D Q D a on e S a STEP 1 Pass fixture wires thru break assembly K if applicable STEP 2 Attach break assembly to shade by threading nipple J onto coupling L if applicable STEP 3 Secure in place by threading loop I onto nipple J NOT SUPPLIED HC 228 112408 OUTLET BOX GROUND WIRE MOUNTING BAR A NUT B QUTLET BOX SCREWS SCREW COLLAR E SCREW COLLAR RING F BREAK ASSEMBLY K COUPLING L CANDLE COVER P FIGURE 1 INSTALLATION HC 228 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 4 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 3 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B Thread screw collar E to nipple C STEP 5 Using 2 pairs of pliers open one link of
Download Pdf Manuals
Related Search
Related Contents
Texas Instruments TAS5518 User's Manual Sharkoon Front bezel 5.25" Open 「FAS住まい新聞(H27.07号)」を配信しています。 Massive Capet 3A1764C - Graco Inc. PDFダウンロード Les travaux en études littéraires - Département des littératures de Emerson UPS Systems Power Supply User Manual Bedienungsanleitung - LTT Copyright © All rights reserved.
Failed to retrieve file