Sea Gull Lighting 8239-965 Installation Guide
Contents
1. SS Your handcrafted solid brass lighting fixture has been coated with a durable baked on acrylic lacquer which gives maximum protection against the weather In time however the brightness of the brass will tarnish giving way to an authentic old world brass finish NOTE To keep your solid polished brass fixture looking new for years to come regularly apply a good quality non abrasive car wax to all metal surfaces giving the fixture an extra protective coating WARNING NOTE DO NOT INSTALL ON A POST OR A POLE THAT RESULTS IN A VERTICAL RISE OF 25 FEET OR HIGHER NOTE This glass is handcrafted the slight imperfections in the glass add to the authenticity of the fixture INSTALLATION HC 233 STEP 1 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED Eoi WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER ASS BROWN GOLD OR BLACK WITHOUT BROWN GOLD OR BLACK WITH TRACER E NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from grou2. SeaGulllighting FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER OFF GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician NOTE Proper wiring is essential for the safe operation of this fixture CAUTION Fixtures with photo cells should be mounted at least 48 from all sides to avoid reflection of light back onto Photo cell causing the Photo cell to malfunction or flicker FINIAL A Installation And Safety Instructions Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM HC 233 012405 IF APPLICABLE TO REMOVE THE PACKAGING 1 Remove the 3 retaining screws and remove the cage 2 Remove the cardboard packaging 3 Replace cage and screws ASSEMBLY Remove finial A and o ring F from center pipe B to remove top assembly C and hood E if applicable Remove cage D if applicable NOTE FOR FIXTURES THAT ARE SOLID BRA
3. at order over center pipe B if applicable STEP 5 Install o ring F and finial A by threading onto center pipe B CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
4. p A and place evenly against the black wire from the outlet box Do Not twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 2 GROUNDING INSTRUCTIONS Connect the ground wire from the fixture bare metal or green insulated wire to the ground wire from the power supply bare metal or green insulated wire using a small wire connector not supplied NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES STEP 3 Slide fitter F onto post Secure in place with screws if applicable FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 Thread center pipe B into coupling between sockets if applicable STEP 2 Install socket cover G STEP 3 Install lamps STEP 4 Install cage D hood E and top assembly C in th
Download Pdf Manuals
Related Search