Sea Gull Lighting 75850-782 Installation Guide
Contents
1. Raise diffuser H to canopy so that center pipe G protrudes through hole in diffuser H Secure in place by threading bottom lockwasher and hexnut C support cup O and finial L onto center pipe G2. Installation And Safety Instructions HC 1303 Sea Gull Lightin Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM 112408 IMPORTANT SAFETY INSTRUCTIONS e Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off e Use of other manufacturers components will void warranty listing and create a potential safety hazard e If you are unclear as to how to proceed contact a qualified electrician e You don t need special tools to install this fixture e Be sure to follow the steps in the order given e Read instructions carefully gt r ma MOUNTING e Save these instructions BAR A FIXTURE MOUNTING NOTE FOR FIXTURES PROVIDED WITH 75 C OR 90 C SUPPLY WIRE FOUND ON CARTON LABEL WARNING ONLY RISK OF FIRE MOST WELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED 60 C CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING GROUNDING SCREW D CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap CANOPY E Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to
3. ly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector clockwise until you feel a firm resistance D Gently try to remove the wires from the connector If you can remove the wires carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire from the fixture and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A If uninsulated ground wire is on the mounting bar A connect the ground wire from the fixture and the outlet box to it using a small wire connector not supplied See Figure 2 NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors After wires are connected tuck them carefully inside outlet box Raise the canopy E to the ceiling allowing for mounting screws I to protrude through key slots N Rotate canopy E clockwise until screws l are in narrow part of keyslot N Tighten screws I with screwdriver STEP 7 Install lamps STEP 8
4. use exact wording from illustration when KEYSLOTS N Da HEX NUT B CENTER PIPE G O ok D J Q O n BEFORE YOU BEGIN Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 Be careful not to misplace any of the screws or parts which are needed to install this fixture STEP 1 Thread center pipe G and hexnut B into coupling M INSTALLATION IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 2 DIFFUSER H Secure mounting bar A to outlet box with outlet box screws not aD TEN WASHER TE supplied Raised side is top as illustrated SUPPORT CUP _ gt gt FINIAL L gt Z STEP 3 Thread fixture mounting screws I into threaded holes of mounting bar A 3 turns each FIGURE 1 NOT SUPPLIED INSTALLATION continued HC 1303 STEP 4 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below i 4 GROUP A GROUP B CONNECT TO BLACK HOUSE WIRE CONNECT TO WHITE HOUSE WIRE BLACK PARALLEL WIRE SQUARE amp RIDGED Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place even
Download Pdf Manuals
Related Search