Sea Gull Lighting 51035-962 Installation Guide
Contents
1. INSTALLATION AND SAFETY INSTRUCTIONS WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER OFF N OUTLET BOX lt WIRE CONNECTORS PL lt MOUNTING SCREWS I NUT G lt a LOCK WASHER F at lt CANOPY 0 CANOPY 5 rA acn CAP NUTS J LOOP E lt CHAIN S FIXTURE LOOP B CENTER PIPE K RETAINING SCREWS N ee lt GLASS M NOT SUPPLIED FIGURE 1 ASSEMBLY Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture NOTE This fixture may be installed either flush mount or chain hung Follow the steps for the mounting method you have chosen FOR FLUSH MOUNT STEP 1 Remove chain S and loop B from fixture Shorten wire and remove loop E from canopy O feed wire through center hole of canopy O and secure with washer F and lock nut G You don t need special tools to install this fixture Be sure to follow the steps in the order given Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician GROUNDING AND MOUNTING BAR LOCK UP x OUTLET BOX GROUND WIRE WIRE lt lt CONNECTORS MOUNTING BAR A MOUN2. TING SCREWS I OUTLET BOX SCREWS FIGURE 2 p REEN Pad GROUNDING SCREW D NOT INCLUDED sea gull lighting Installation And Safety Instruction HC 603 Fill In Item Number On Carton And File This Sheet For Fixture Reference 060304 ITEM INSTALLATION HC 603 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Thread fixture mounting screws I in through top of mounting bar A raised side is on top as illustrated Run screw threads all the way down to the heads Secure mounting bar A to outlet box with outlet box screws not supplied FOR CHAIN HUNG STEP 2 Using 2 pairs of pliers open one link of chain S and connect it to the fixture loop B at the top of the fixture STEP 3 Open one link on the other end of the chain S and attach it to the canopy loop E BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY STEP 4 Lace wires up through chain S and pass wires through hole in canopy loop E We recommend lacing wire up through every other link of chain S WIRING INSTRUCTIONS A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE O O as PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED D D E Note When
3. parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire F from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire F from the fixture if supplied and the outlet box to it using a small wire connector not supplied NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the p
4. roduct identifies products manu factured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box and then raise the canopy O against ceiling allowing for mounting screws l to protrude through holes in canopy O Secure in place with cap nuts J STEP 2 Insert lamp s STEP 3 Raise glass M to mounting brace and secure with retaining screws N CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
Download Pdf Manuals
Related Search