Sea Gull Lighting 77088-98 Installation Guide
Contents
1. have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box Raise the canopy E to the ceiling allowing for mounting screws C to protrude through key slots N Rotate canopy E clockwise until screws C are in narrow part of keyslot N Tighten screws C with screwdriver STEP 2 Install lamp s STEP 3 Place glass H inside ring G and secure in place with tabs L attached to ring G STEP 4 Raise ring G to canopy E so that threaded brackets I protrude through holes in ring G and secure in place with ball nuts J CLEANING To clean wipe fixture body with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts2. EY WITHOUT TRACER SSS BROWN GOLD OR BLACK WITHOUT BROWN GOLD OR BLACK WITH TRACER Nn Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connecior off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 6 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire M from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire M from the fixture if supplied and the outlet box to it using a small wire connector not supplied NOTE Underwriters Laboratories U L does not require all fixtures to
3. HTLY BEND THE BRACKETS I TOWARDS THE CEILING GROUNDING AND MOUNTING BAR LOCK UP OUTLET BOX GROUND WIRE WIRE E CONNECTORS MOUNTING BAR A MOUNTING SCREWS C AS soutter BOX SCREWS p p S GREEN amp GROUNDING SCREW D NOT INCLUDED FIGURE 2 NOTE FOR FIXTURES PROVIDED WITH 75 C OR 90 C SUPPLY WIRE WARNING ONLY THESE WARNINGS ARE PROVIDED ON THE U L LABEL AND ON THE FIXTURE CARTON RISK OF FIRE MOST DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED 60 C CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING 58a Gull lighting Installation And Safety Instruction HC 471 Fill In Item Number On Carton And File This Sheet For Fixture Reference 052699 ITEM INSTALLATION HC 471 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Secure mounting bar A to outlet box with outlet box screws not supplied Raised side is top as illustrated STEP 2 Thread fixture mounting screws C into threaded holes of mounting bar A 3 turns each A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below i GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED WHITE OR GREY WITH TRACER WHITE OR GR
4. INSTALLATION AND SAFETY INSTRUCTIONS FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER SET AT OFF GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician OUTLET OUTLET BOX SCREWS BOX MOUNTING BAR A La PF i MOUNTING SCREWS C WIRE CONNECTORS KEYSLOTS N BRACKET I CANOPY E GLASS H RING G TABS L BALL NUTS J FIGURE 1 NOT INCLUDED IF SUPPLY WIRES ARE LOCATED WITHIN 3 OF BALLAST USE WIRE RATED FOR AT LEAST 90 C ASSEMBLY Carefully remove the fixture from the carton and check that all parts are included as shown in figure 1 and 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture Before mounting canopy E to mounting bar A place canopy E on flat surface Next place ring G over canopy E making sure the three brackets I protrude through holes in canopy E If they do not adjust the brackets I so that they align with the canopy E holes NOTE IF LIGHT LEAKAGE IS PRESENT SLIG
Download Pdf Manuals
Related Search