Sea Gull Lighting 7355-15 Installation Guide
Contents
1. STEP 3 Thread nipple G into socket F NOTE Nipple may be factory installed STEP 4 Place fiber washer H on socket nipple G position diffuser 1 on nipple G and secure with knob J Do not overtighten CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts2. directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH WHITE OR GREY WITH TRACER PARALLEL WIRE SQUARE amp RIDGED eS WHITE OR GREY WITHOUT TRACER BROWN GOLD OR BLACK WITHOUT TRACER BROWN GOLD OR BLACK WITH TRACER SS NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box Do Not twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS Your fixture can be grounded in a variety of different ways Choose the instructions below which applies to your fixture and follow directions carefully NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The li
3. INSTALLATION AND SAFETY INSTRUCTIONS FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER OFF GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician WARNING FOR FIXTURES PROVIDED WITH 75 C OR 90 C SUPPLY WIRE WARNING ONLY THESE WARNINGS ARE PROVIDED ON THE U L LABEL AND ON THE FIXTURE CARTON WARNING RISK OF FIRE MOST DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED 60 C CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING OUTLET a OUTLET MOUNTING BAR A MOUNTING SCREWS I WIRE yu CONNECTORS d lt _ _ _NIPPLE G FIBER WASHER H DIFFUSER I C KNOB J NOT INCLUDED FIGURE 1 ASSEMBLY Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture NOTE Socket may be factory installed STEP 1 To clear a path through canopy B fiberglass push screwdriver through canopy cente
4. r hole D STEP 2 Position center holes D over one another so that the fiberglass is visible through all holes STEP 3 Pass the fixture wires through center hole D in canopy B Align socket clip E and canopy B center hole D and push together until socket F locks Secure in place by inserting a screw driver blade through each side of clip and pry outward if applicable STEP 4 Push screwdriver blade through keyholes C to clear a path for mounting screws l GROUNDING AND MOUNTING BAR LOCK UP MOUNTING BAR A MOUNTING SCREWS I GROUNDING SCREW Z ane NOT INCLUDED FIGURE 2 NOTE FOR FIXTURE EMPLOYING A GROUNDED CONVENIENCE OUTLET CAUTION THIS FIXTURE EMPLOYS A GROUNDED TYPE RECEPTACLE AND IS NOT INTENDED FOR CONNECTION TO A TWO WIRE UNGROUNDED SOURCE OF SUPPLY Asea guli lighting Installation And Safety Instruction HC 166 Fill In Item Number On Carton And File This Sheet For Fixture Reference 092800 ITEM INSTALLATION HC 166 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET STEP 1 Secure mounting bar A to outlet box with outlet box screws not supplied Raised side is top as illustrated w i gt lt STEP 2 Thread fixture mounting screws I into threaded holes of mounting bar A 3 turns each A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the
5. sting mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs A For fixtures with green grounding screws on mounting bar the green grounding screw is to be inserted into the hole with two raised dimples provided on the mounting bar Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw on the mounting bar in clockwise direction and tighten the screw B For fixtures with uninsulated wire on mounting bar connect the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire to the insulated wire on mounting bar using a small wire connector not supplied C For fixtures with uninsulated wire direct from fixture connect the uninsulated wire from the fixture to the ground wire from the outlet box bare metal or green insulated wire using a small wire connector NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box Raise the canopy B to the ceiling allowing for mounting screws I to protrude through key slots Rotate canopy B clockwise until screws l are in narrow part of keyslot Tighten screws I with screwdriver STEP 2 Install lamps
Download Pdf Manuals
Related Search