Sea Gull Lighting 77850-782 Installation Guide
Contents
1. QUTLET BOX SCREWS CHAIN S NOT INCLUDED FIXTURE LOOP 1 FLUSH CANOPY 2 gt CAP NUTS Y DECORATIE sea gull lighting Installation And Safety Instruction BOTTOM DIFFUSER 0 H C 1 3 04 031108 NIPPLE M gt qD NUT amp LOCKWASHER P Fill In Item Number On Carton And FIGURE 1 FINIAL L SS NOT SUPPLIED File This Sheet For Fixture Reference ITEM INSTALLATION HC 1304 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET OX FOR CHAIN HUNG STEP 1 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 5 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B Thread screw collar E to nipple C STEP 2 Using 2 pairs of pliers open one link of chain S and connect it to the fixture loop I at the top of the fixture STEP 3 Slide the screw collar ring G and canopy H in that order over chain S Open one link on the other end of the chain S and attach it to the screw collar E which has been mounted to the ceiling nipple C BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY FOR FLUSH MOUNT STEP 1 Thread mounting screws K into offset mounting bar N Run mounting screws K all the way down to their heads Secure offset mounting bar N to the outlet box raised side to top as illustrated using outlet box screws not suppli2. INSTALLATION AND SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS ASSEMBLY Be sure the electricity to the system you are working on is turned Carefully remove the fixture from the carton and check that all parts off either the fuse removed or the circuit breaker set at off are included as shown in Figure 1 amp 2 Be careful not to misplace Use of other manufacturers components will void warranty listing any of the screws or parts which are needed to install this fixture and create a potential safety hazard To reduce the risk of fire electric shock or personal injury mount to STEP 1 outlet box or supporting system able to support the weight of the Thread fixture loop I to fixture if applicable fixture If you are unclear as to how to proceed contact a qualified electrician You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully Save these instructions GROUNDING AND MOUNTING BAR LOCK UP FLUSH MOUNT OUTLET BOX GROUND WIRE NUT B Ee QUIET Box GROU SCREWS WWE NIPPLE C 5 J lt CONNECTORS GREEN GROUNDING OFFSET CANOPY H SCREW D MOUNTING BAR N SCREW COLLAR E m MOUNTING SCREW COLLAR SCREWS K RING G FIGURE 2 lt
3. an be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
4. ed STEP 2 Remove fixture loop I from flush canopy Z Feed fixture wires through center of flush canopy Z Secure flush canopy Z to fixture by installing lock washer and nut over center nipple STEP 1 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE _ PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED CET Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector clockwise until you feel a firm resistance D Gently try to remove the wires from the connector If you can remove the wires carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 2 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimple
5. s provided on the mounting bar A Wrap the ground wire F from the fixture and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire F from the fixture and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 CHAIN HUNG ONLY After wires are connected tuck them carefully inside outlet box and then raise the canopy H against ceiling and thread the screw collar ring G to the screw collar E STEP 2 FLUSH MOUNT ONLY Place flush canopy Z to ceiling so mounting screws K are obstructed and secure by threading cap nuts Y to mounting screws K STEP 3 Install lamps STEP 4 Place decorative ring X on top of diffuser O STEP 5 Raise diffuser O over bottom nipple M and secure by threading nut and lock washer P and finial L to bottom nipple M CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders n a D 2 fe o se a 2 se o lt 0 ne tev ne D Ta ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture c
Download Pdf Manuals
Related Search