Sea Gull Lighting 77625-962 Installation Guide
Contents
1. STEP 3 Slide the screw collar ring G and canopy H in that order over chain S Open one link on the other end of the chain S and attach it to the screw collar E which has been mounted to the ceiling nipple C BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY FOR FLUSH MOUNT STEP 1 Thread mounting screws K into offset mounting bar N Run mounting screws K all the way down to their heads Secure offset mounting bar N to the outlet box raised side to top as illustrated using outlet box screws not supplied STEP 2 Remove fixture loop I from fixture Feed fixture wires through center of flush canopy Secure flush canopy to fixture by installing lock washer and nut over center nipple STEP 1 A Use a listed wire connector to connect the fixture hot wire black wire or round and smooth tracer to the supply hot wire B Use a listed wire connector to connect the fixture common wire white wire or square and rigid to the supply common wire C Gently try to remove the wires from the connector If you can remove the wires carefully re do the wiring connection STEP 2 GROUNDING INSTRUCTIONS Connect the supply ground wire fixture ground wire and mounting bar ground wire pre attached using the supplied wiring connector Gently try to remove the wires from the connector If you can remove the wires carefully re do the wiring connection FINAL ASSEMBLY Make sure no bare wires can be seen outside2. Installation And Safety Instructions HC 1565 a Sea Gull Lighting Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM 083109 IMPORTANT SAFETY INSTRUCTIONS GROU NDING AND MOU NTI NG e Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off BAR LOC K U P FLUSH MOU NT e Use of other manufacturers components will void warranty listing lt OUTLET BOX and create a potential safety hazard e To reduce the risk of fire electric shock or personal injury mount to outlet box or supporting system able to support the weight of the fixture ee GROUND WIRE e If you are unclear as to how to proceed contact a qualified electrician GREEN WI e You don t need special tools to install this fixture SCREW S s IS CONNECTORS e Be sure to follow the steps in the order given i OFFSET e Under no circumstances should a fixture be hung on house electrical MOUNTING wires nor should a swag type fixture be installed on a ceiling which OUTLET BOX Ap N contains a radiant type heating system SCREWS gt a SCREWS K e Read instructions carefully FIGURE 2 NOT INCLUDED e Save these instructions CLEANING To clean wipe fixture with a soft cloth Clean glass with
3. a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper GROUND WIRE ORDERING PARTS WIRE gt CONNECTORS Keep this sheet for future reference and in case you need to order OUTLET BOX replacement parts Parts for this fixture can be ordered from place MOUNTING of purchase Be sure to use exact wording from illustration when NUT B Ei BAR A ordering parts OUTLET BOX NIPPLE C SCREWS M Carefully remove the fixture from the carton and check that all parts SCREW COLLAR SCREW are included as shown in Figure 1 Be careful not to misplace any of RING G COLLAR E the screws or parts which are needed to install this fixture Thread fixture loop I to fixture if applicable FIXTURE LOOP I CHAIN S QO pt JR DIFFUSER 0 BOTTOM NIPPLE P FINIAL L SS FIGURE 1 NOT SUPPLIED INSTALLATION HC 1565 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX FOR CHAIN HUNG STEP 1 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 5 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B Thread screw collar E to nipple C STEP 2 Using 2 pairs of pliers or chain breaks open one link of chain S and connect it to the fixture loop I at the top of the fixture Please be sure to open chain link in an outward motion
4. wire connectors STEP 1 CHAIN HUNG ONLY Make sure no bare wires can be seen outside wire connectors After wires are connected tuck them carefully inside outlet box Push the fixture firmly over the mounting screws F and against the wall Secure canopy I in place with cap nuts E STEP 2 FLUSH MOUNT ONLY Place flush canopy to ceiling so mounting screws K protrude through flush canopy and secure by threading cap nuts to mounting screws K Install lamps Raise diffuser O over bottom nipple P and secure by placing decorative cup M to diffuser O and threading finial L to bottom nipple P Arms J should protrude through diffuser O Thread ball nuts F onto arms to secure
Download Pdf Manuals
Related Search