Home Decorators Collection AM113-BN Instructions / Assembly
Contents
1. To hang your fan where there is an existing fixture but no ceiling joist you may need an installation hanger bar QQ not included as shown above HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly 1 Preparing the canopy Remove the canopy ring B from the canopy C Remove the two non slotted mounting bracket screws BB from the canopy C and loosen the slotted mounting bracket screws BB on the canopy C Remove the canopy C from the mounting bracket A by turning the canopy C counterclockwise BB 3 Assembling the fan WARNING Failure to properly install the cotter pin HH could result in the fan loosening and possibly falling NOTE If a longer downrod not included is needed take out the screw located in the hanger ball RR lower the hanger ball RR and remove the pin Il Remove all three pieces from the downrod and assemble them onto the new longer downrod before proceeding to the downrod installa tion Carefully feed the motor wires up through the downrod SS Thread the downrod SS into the collar Next line up the holes and replace the cotter pin HH and clevis pin GG Tighten the two collar setscrews KK Slip coupling cover E canopy ring B and canopy C onto the downrod SS Carefully reinstall the hanger ball RR2. Remote control holder b b b Installation MOUNTING OPTIONS WARNING To reduce the risk of fire electric shock or personal injury mount the fan to an outlet box marked acceptable for fan support using the screws provided with the outlet box An outlet box commonly used for the support of lighting fixtures may not be acceptable for fan support and may need to be replaced If in doubt consult a qualified electrician NOTE You may need a longer downrod to maintain proper blade clearance when installing on a steep sloped ceiling The maximum angle allowable is 18 away from horizontal If m the canopy C touches the hanger ball downrod assembly D turn the canopy C 180 before attaching the canopy C to the mounting bracket A If your ceiling fan does not have an existing UL listed mounting box then install one using the following instructions Disconnect the power by removing the fuses or turning off the circuit breakers Secure the outlet box PP not included directly to the building structure Use appropriate fasteners and materials not included The outlet box and its bracing must be able to fully support the weight of the moving fan at least 35 Ibs Do not use a plastic outlet box The illustrations below show three different ways to mount the outlet box PP not included PP 00
3. Carefully lift the fan motor assembly F up to the mounting bracket A and seat the hanger ball downrod assembly D in the mounting bracket A socket Make sure the tab on the mounting bracket A socket is properly seated in the groove in the hanger ball downrod assembly D This will help to balance the ceiling fan HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly Hanging the Fan continued Preparing the receiver and remote control WARNING To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring CAUTION The frequency switches on the receiving unit are covered with a rubber cover Remove the rubber cover and then replace it after making any changes to the frequency switches CAUTION Do not use with a wall light dimmer switch If you feel you do not have enough electrical wiring knowledge or experience have your fan installed by a licensed electrician This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units The frequency switches on your receiver L and remote control M have been preset at the factory Please recheck to make sure the switches on the remote control M and the receiver L are set to the same position Any combination of settings will operate the fan as long as the switches in the remote control M
4. 16 Installing the Remote Control Holder 16 Reverse Switch Operating Instructions 17 Care and Cleaning eee 17 Troubleshooting s Vene on e 18 Service Parts 19 Safety Information 1 reduce the risk of electric shock ensure electricity has been turned off at the circuit breaker or fuse box before beginning 2 All wiring must be in accordance with the National Electrical Code ANSI NFPA 70 1999 and local electrical codes Electrical installation should be performed by a qualified licensed electrician 3 outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 Ibs Use only UL listed outlet boxes marked FOR FAN SUPPORT 4 The fan must be mounted with a minimum of 7 ft clearance from the trailing edge of the blades to the floor 5 Avoid placing objects in the path of the blades 6 To avoid personal injury or damage to the fan and other items be cautious when working around or cleaning the fan 7 Do not use water or detergents when cleaning the fan or fan blades A dry dust cloth or lightly dampened cloth will be suitable for most cleaning 8 After making electrical connections spliced conductors should be turned upward and pushed carefully up into the outlet
5. Glass shade Receiver Remote control 2 Remote control holder 19 AA Yy JJ zz LL Q GG NN M N HH OO E Part Description AA Plastic wire nut BB Mounting bracket screw preassembled CC Blade attachment screw and fiber washer DD Blade arm screw and lock washer preassembled EE Remote control holder mounting screw FF Remote control holder plug preassembled GG Clevis pin preassembled HH Cotter pin preassembled ll Cross pin preassembled JJ Setscrew preassembled KK Collar setscrew preassembled LL Light kit mounting plate screw preassembled MM Light kit mounting screw preassembled NN 100 watt JD type halogen bulb 00 12V MN21 A23 battery HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance HOME DECORATORS COLLECTION Questions problems missing parts Before returning to the store call Home Decorators Collection Customer Service 8 a m 6 p m EST Monday Friday 1 800 986 3460 HOMEDEPOT COM HOMEDECORATORS Retain this manual for future use AM113000001 Y
6. and receiver L are set to the same position After checking the switches insert the receiver L into the mounting bracket A with the flat side of the receiver L facing the ceiling 10 Assembly Hanging the Fan continued T Making the electrical connections AN WARNING Check to see that all connections are tight including ground and that no bare wire is visible at the wire nuts except for the ground wire CAUTION Do not use with a wall light dimmer switch a NOTE The fan must be installed at a maximum distance of 20 feet from the remote control for proper signal transmission between the remote control and the fan s receiving unit Follow the steps below to connect the fan to your household wiring Use the plastic wire nuts AA with your fan Secure the plastic wire nuts AA with electrical tape Make sure there are no loose strands or connections Motor to receiver electrical connections Connect the black wire TT from the fan to the black wire AAA marked TO MOTOR from the receiver L Connect the white wire VV from the fan to the white wire CCC marked TO MOTOR from the receiver L Connect the blue wire UU from the fan to the blue wire BBB marked For Light from the receiver L Receiver to house supply wires electrical connections Connect t
7. HOME Item 657 836 DECORATORS Model AM113 BN COLLECTION USE AND CARE GUIDE CASSARO II 52 IN CEILING FAN Questions problems missing parts Before returning to the store call Home Decorators Collection Customer Service 8 a m 6 p m EST Monday Friday 1 800 986 3460 HOMEDEPOT COM HOMEDECORATORS THANK YOU We appreciate the trust and confidence you have placed in Home Decorators Collection through the purchase of this ceiling fan We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Home Decorators Collection Table of Contents Table of Contents 2 Safety Information cereus 3 Warranty 4 ecu terrre eror onion nena nnn 4 4 Tools Required eicere 4 Hardware Incl detl 5 Package Contents erect neta tn tn nnnna tnn 6 IEEE NITUNRE 7 Lc ule 8 Hanging 9 Attaching the Fan Blades 13 Itistallirig the Light 14 Operation senses 16 Remote Control Operating Instructions
8. box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box 9 All setscrews must be checked and retightened where necessary before installation not use this fan with any solid state fan speed control device j WARNING To reduce the risk of electrical shock or fire do It will permanently damage the electronic circuitry WARNING To reduce the risk of personal injury do not bend the blade arms also referred to as flanges when installing the brackets balancing the blades or cleaning the fan WARNING Do not insert foreign objects between rotating fan blades WARNING To reduce the risk of fire electric shock or personal injury mount the fan to the outlet box marked acceptable for fan support with the screws provided with the outlet box CAUTION To reduce the risk of personal injury use only the screws provided with the outlet box NOTICE This fan includes a 190W limiter to comply with the Department of Energy 2009 regulation Lamping this product over 190W will cause this fan not to light Please use bulbs with a total wattage under the 190W regulation HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Warranty We warrant the fan motor to be free from defects in workmanship and material present at time o
9. f shipment from the factory for a period of lifetime after the date of purchase by the original purchaser We also warrant that all other fan parts excluding any glass or acrylic blades to be free from defects in workmanship and material at the time of shipment from the factory for a period of two years after the date of purchase by the original purchaser We agree to correct such defects without charge or at our option replace with a comparable or superior model if the product is returned To obtain warranty service you must present a copy of the receipt as proof of purchase All costs of removing and reinstalling the product are your responsibility Damage to any part such as by accident misuse improper installa tion or by affixing any accessories is not covered by this warranty Because of varying climatic conditions this warranty does not cover any changes in brass finish including rusting pitting corroding tarnishing or peeling Brass finishes of this type give their longest useful life when protected from varying weather conditions A certain amount of wobble is normal and should not be considered a defect Servicing performed by unauthorized persons shall render the warranty invalid There is no other express warranty We hereby disclaim any and all warranties including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law The duration of any implied warranty which cannot be disclai
10. he black hot wire FFF from the ceiling to the black wire DDD marked AC in L from the receiver L Connect the white neutral wire GGG from the ceiling to the white wire EEE marked AC in N from the receiver L 11 If your outlet box PP has a ground wire HHH green or bare copper connect it to the fan ground wires II otherwise connect the hanger ball downrod assembly D ground wire to the mounting bracket Secure each wire connection with plastic wire nut AA provided with the electrical hardware After connecting the wires spread them apart so that the green and white wires are on one side of the outlet box PP and the black and blue wires are on the other side Carefully tuck the wire connections up into the outlet box PP FFF GGG HHH HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly Hanging the Fan continued 8 Installing the canopy properly sits in the groove in the hanger ball downrod assembly D before attaching the canopy C to the mounting WARNING Make sure the tab on the mounting bracket A bracket A by turning the canopy C until it drops into place WARNING The locking slots of the canopy C are provided only as an aid to mounting Do not leave the fan assembly unattended until all four canopy mounting bracket screws BB are engaged and firmly tightened Slide the canopy C up to
11. he light kit mounting plate and loosen the other two screws MM Do not remove While holding the light kit J under your fan motor assembly F make the wire connections White to white Black to black Place the key holes in the light kit J over the two mounting screws MM previously loosened from the light kit mounting plate I Turn the light kit J until the light kit J locks in place at the narrow section of the key holes Secure by tightening the two light kit mounting screws MM previously loosened and the one MM previously removed MM Assembly Installing the Light Kit continued 1 Finishing the light kit and attaching the glass shade CAUTION Before starting installation disconnect the power by turning off the circuit breaker or removing the fuse at the fuse box Turning power off using the fan switch is not sufficient to prevent electric shock Install one 100 watt JD type halogen bulb NN included Raise the glass shade K up against the light kit J and secure it to the fan by turning the glass shade K clockwise until snug DO NOT OVERTIGHTEN Restore power and your light kit is ready for opera tion 15 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Operation REMOTE CONTROL OPERATING INSTRUCTIONS Install the 12V MN21 A23 battery 00 included into the remote control M To p
12. ion The fan will not start Check the main and branch circuit fuses or breakers Check the line wire connections to the fan and switch wire connections in the switch housing Check to make sure the dip switches from the remote control and receiver are set to the same frequency The fan sounds noisy Make sure all motor housing screws are snug Make sure the screws that attach the fan blade arm to the motor hub are tight Make sure the wire nut connections are not rattling against each other or the interior wall of the switch housing Allow a 24 hour breaking in period Most noises associated with a new fan disappear during this time If using the ceiling light kit make sure the glassware are secured tight Check that the light bulb is also secure Make sure there is a short distance from the ceiling to the canopy It should not touch the ceiling Make sure your ceiling box is secure and that rubber isolator pads are used between the mounting bracket and outlet box Lights shut off and will not come back on This unit is equipped with a wattage limiting device Lamping in excess of 190 watts will disable your Ceiling fan s light kit To reset your light kit you must turn the power off and relamp keeping the wattage under 190 watts Restore power to your ceiling fan and continue normal operation The remote control
13. is not working Do not connect the fan with wall mounted variable speed control s Make sure the frequency switches are set correctly The fan wobbles Verify that all blades and blade bracket screws are secure most fan wobble problems are caused by loose parts Once the fan is properly installed run the ceiling fan for 10 minutes to let the fan self adjust If wobble occurs after running the fan for 10 minutes verify blade level using the following process Select a point on the ceiling above the tip of one of the blades then select any fan blade and measure from the center of the selected blade to the point on the ceiling Rotate the fan until the next blade is positioned and repeat the measurement using the same point from the ceiling for every blade Measurement deviations should be within 1 8 in Ifall deviations are less than 1 8 in and the fan continues to wobble please call Customer Service 1 800 986 3460 to order a complimentary Blade Balancing Kit f deviation is greater than 1 8 in please call Customer Service 1 800 986 3460 to order complimentary replacements of your brackets 18 Service Parts Part Description Mounting bracket preassembled Canopy ring preassembled Canopy Hanger ball downrod assembly Coupling cover Fan motor assembly Blade Blade arm Light kit mounting plate Light kit
14. itioner on a warmer setting without affecting your comfort Cool weather Clockwise Direction An upward air flow moves warm air off the ceiling This allows you to set your heating unit on a cooler setting without affecting your comfort Le cu Care and Cleaning Do Check the support connections brackets and blade attachments twice a year Make sure they are secure Because of the fan s natural movement some connections may become loose over time It is not necessary to remove the fan from the ceiling Clean your fan periodically Use only a soft brush or lint free cloth to avoid scratching the finish The plating is sealed with a lacquer to minimize discoloration or tarnishing Optional Apply a light coat of furniture polish to the wood blades Optional Cover small scratches with a light application of shoe polish Do not Use water when cleaning Water could damage the motor or the wood or possibly cause an electrical shock Apply oil to your fan or motor The motor has permanently lubricated sealed ball bearings HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Troubleshooting panel box before you attempt any repairs Refer to step 7 WARNING Make sure the power is off at the electrical Making the electrical connections on page 11 Problem Solut
15. med is limited to the time period as specified in the express warranty Some states do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you The retailer shall not be liable for incidental consequential or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law Some states do not allow the exclusion of incidental or consequential damages so the above exclusion or limitation may not apply to you This warranty gives specific legal rights and you may also have other rights which vary from state to state This warranty supersedes all prior warranties Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer Contact the Customer Service Team at 1 800 986 3460 or visit www HOMEDEPOT COM HOMEDECORATORS Pre Installation SPECIFICATIONS Fan size Speed Volts Amps Watts RPM CFM N W G W C F 5 in 120 13 z 52 Medium 0 43 32 119 3504 21 38 Ib 25 83 Ib High 0 50 59 170 5295 NOTE These are approximate measures They do not include amps and wattage used by the light kit LISTED TOOLS REQUIRED Phillips Flat blade Step Wire Electrical screwdriver screwdriver ladder stripper tape Pre Installation continued HARDWARE INCLUDED NOTE Hardware shown to actual si
16. onto the downrod SS Ensure that the cross pin Il is in the correct position the setscrew JJ is tightened and the wires are not twisted 2 Preparing the motor Remove the clevis pin GG and cotter pin HH and loosen the two collar setscrews KK from the motor collar Take out the setscrew JJ located in the hanger ball RR lower the hanger ball RR and remove the cross pin II Remove the hanger ball RR from the hanger ball downrod assembly D Assembly Hanging the Fan 4 Installing the mounting bracket to the electrical box Hanging the fan to the mounting bracket WARNING To reduce the risk of fire electric shock or other personal injury mount the fan only to an outlet box or supporting system marked acceptable for fan support and use the mounting screws provided with the outlet box WARNING The tab in the ring must rest in the groove of the hanger ball downrod assembly D Failure to properly seat the tab in the groove could cause damage to the wiring Pass the 120 volt supply wires through the center hole in the mounting bracket A Attach the mounting bracket A on the outlet box PP by sliding the mounting bracket A over the screws provided with the outlet box PP Note that the flat side of the mounting bracket A is toward the outlet box PP Securely tighten the two mounting screws PP
17. revent damage to the remote control M remove the battery if not used for long periods Restore power to the ceiling fan and test for proper operation HI MED LOW buttons Sets the fan speed OFF button Turns the fan off 00 AE button Turns the light on or off and also controls the brightness setting Press and release this button to turn the light on or off Press and hold the button to set the desired brightness The light button has an auto resume it will stay at the same brightness as the last time it was turned off FF INSTALLING THE REMOTE CONTROL HOLDER Remove the two remote control holder plugs FF from the remote control holder N Note that the plugs have unique tabs that allow them to fit only in one hole Attach the remote control holder N with the two remote control holder mounting screws EE Replace the two remote control holder plugs FF each into its own hole 16 Operation continued REVERSE SWITCH OPERATING INSTRUCTIONS The reverse switch is located on the top of the motor housing Slide the switch to the left for warm weather operation Slide the switch to the right for cool weather operation NOTE Wait for the fan to stop before reversing the direction of the blade rotation Warm weather Counterclockwise Direction A downward air flow creates a cooling effect This allows you to set your air cond
18. t the blade arm H through the slot in the housing Align the holes in the blade arm H and the fan motor assenbly F and secure with a blade arm attachment screw and lock washer DD Repeat this procedure with the remaining blade arms H WW G CN lt g A a DD 13 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly Installing the Light Kit 1 Attaching the light kit mounting plate to the mounting ring Remove one of the three light kit mounting plate screws LL from the mounting ring JJJ and loosen the other two screws Do not remove Place the key holes in the light kit mounting plate over the two screws LL previously loosened from the mounting ring JJJ Turn the light kit mounting plate I until the light kit mounting plate locks in place at the narrow section of the key holes Securely tighten the two light kit mounting plate screws LL previously loosened and the one LL previously removed 14 1 Attaching the light kit to the light kit mounting plate CAUTION Before starting installation disconnect the power by turning off the circuit breaker or removing the fuse at the fuse box Turning power off using the fan switch is not sufficient to prevent electric shock Remove one of the three light kit mounting screws MM from t
19. the ceiling Make sure you have placed the wires safely into the outlet box PP Secure the canopy C to the mounting bracket A with the four canopy mounting bracket screws and lock washers BB included with your fan Raise up canopy ring B and line up the four tabs with the four grooves on the canopy C Once lined up slide the canopy ring B and secure it to the canopy C until snug 12 Assembly Attaching the Fan Blades Preparing the blade and blade arm Insert the blade arm H into the hole in the front of the blade G 9 1 Attaching the blades to the blade arms Attach the blade arm H to the blade G using the screws with fiber washers CC provided Start a screw CC into the blade arm H and do not tighten Repeat repeat for the two remaining screws and fiber washers CC Tighten each screw CC securely starting with the center screw CC Repeat the steps for the remaining blades G Fastening the blade assemblies to the motor 11 WARNING To reduce the risk of personal injury do not bend the blade arms H while installing balancing the blades G or cleaning the fan Do not insert foreign objects between rotating fan blades G WARNING Remove the three rubber packing mounts WW from the fan motor assembly and discard prior to attaching the blades G Inser
20. ze unless noted otherwise in the table below AA B KK FF LL BB GG E NN T a OO E DD JJ Part Description Quantity AA Plastic wire nut 9 BB Mounting bracket screw preassembled 2 CC Blade attachment screw and fiber washer 16 DD Blade arm screw and lock washer preassembled 11 EE Remote control holder mounting screw not to scale 2 FF Remote control holder plug preassembled 2 GG Clevis pin preassembled 1 HH Cotter pin preassembled 1 ll Cross pin preassembled 1 JJ Setscrew preassembled 1 KK Collar setscrew preassembled 2 LL Light kit mounting plate screw preassembled 3 MM Light kit mounting screw preassembled 3 NN 100 watt JD type halogen bulb not to scale 1 00 12V MN21 A23 battery not to scale 1 5 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Pre Installation continued PACKAGE CONTENTS Part Description Mounting bracket preassembled Quantity Canopy ring preassembled Canopy Hanger ball downrod assembly Coupling cover Fan motor assembly olnm gt Blade a ae Part Description Blade arm Quantity Light kit mounting plate Light kit Glass shade Receiver Remote control 2
Download Pdf Manuals
Related Search