Total Pond A16531L Installation Guide
Contents
1. e Risk of electrical shock This pump has not been investigated for use in swimming pools or marine areas CAUTION e This pump has been evaluated for use with water only e Use aproper power source as indicated on the pump label e Keep the cord away from high temperatures or other heat sources e Do not pump heated liquids e Do not let the pump run dry Pump must be completely submerged for proper operation and cooling e Operate in freshwater only Avoid heavily chlorinated water and water with high pH levels e Do not lift the pump by its power cord PREPARATION Before beginning assembly or operation of product make sure all parts are present Compare parts with package contents list and diagram above If any part is missing or damaged do not attempt to assemble install or operate the product Contact customer service for replacement parts e Estimated Assembly Time 30 minutes e Tools required for assembly container plastic liner or sealant drill 1 1 4 drill bit silicone caulk latex gloves OPERATION INSTRUCTIONS 1 Connect the extension tubes to the pump Fig 1 2 Choose a fountain head for the desired water effect and assemble your choice as shown in Fig 2 3 4 Choose a container for your fountain kit Fig 3 a Fig 3 If the container is not already watertight use a plastic liner Or if a clay pot is used spray the inside of the pot with a clear acrylic Liner sealant Be sure2. Fig 10 11 Use the cord holder to tie a loop in the cord This will help the pump stay in place Fig 11 MAINTENANCE PROCEDURE 1 Unplug the pump and remove it from the container Fig 12 2 Remove the fountain head and extension tube Turn over the filter box assembly Open the filter housing by pushing on the sides of the housing As you press on the sides of the filter housing the top and bottom will unlock Fig 13 3 Pull off the cover and remove the filter pad Rinse the filter pad to remove any debris Fig 14 4 Disassemble the pump and clean the internals of the pump Fig 15 5 Reassemble the pump and filter box kit Fig 16 CARE AND MAINTENANCE e Regular cleaning of the pump may be necessary depending upon the environment in which it is operated Clean the pump when it is visibly soiled or when a drop in performance is detected e Before cleaning always disconnect the pump from the power source e Remove all parts from the pump and clean in warm soapy water e Disassemble the front cover and remove the impeller cover to expose the impeller assembly Use a soft cloth or brush to clean the impeller assembly and the inside of the impeller housing Refer to the diagram in the replacement parts list TROUBLESHOOTING If the pump fails to operate e Check to make sure the power cord is plugged in and the pump is getting power e Check the pump outlet and any tubing fountains spitters etc for kinks or obstru
3. manufacturer to either replace and or repair at the manufacturer s sole discretion the product as described above Neither seller nor the manufacturer shall be liable for injury loss or damages for lost profits lost sales injury to person or property or any other incidental or consequential loss arising from any cause whatsoever no matter whether based upon warranty contract negligence or other misuse and the buyer and user agree that no other remedy shall be available to them Before using the buyer and user shall determine the suitability of the product for the intended use and assume all risk and liability whatsoever in connection therewith The warranty and remedy described in this limited warranty is an exclusive warranty and remedy in lieu of any other warranty or remedy expressed or implied All other warranties and remedies are hereby expressly excluded including but not limited to any implied warranty of merchantability of fitness for any particular purpose This warranty gives the buyer and user specific legal rights and buyer and user may also have other rights which vary from state to state Some states do not allow exclusions or limitations of incidental or consequential damages so the above limitations or exclusions may not apply to you CALL 1 888 412 6001 BEFORE RETURNING TO STORE
4. OONN ITEM A16531L LA Zon Container Fountain Kit with LED TotalPond Light REMINDER Questions problems missing parts Before returning to your CALL 1 888 412 6001 retailer call our customer service department at BEFORE RETURNING TO STORE 1 888 41 2 6001 8 a m 6 p m EST Monday Friday or email us at customercare totalpond com Or visit our website www totalpond com PACKAGE CONTENTS Part Description Quantity A Pump with filter and LED light 1 B Extensions 4 C Extension tubes 1 D Waterspray nozzle 1 E Waterbell nozzle insert 1 F Trumpet nozzle insert 1 G Lower fountain head nozzle 1 H Epoxy putty part A 1 Epoxy putty part B 1 J Cord holder 1 A WARNINGS AND CAUTIONS WARNING e Risk of electrical shock This pump is supplied with a grounding conductor and grounding type attachment plug To reduce the risk of electric shock be certain that it is connected only to a properly grounded grounding type receptacle e Do not exceed the voltage shown on the pump e Always disconnect pump from the power source before beginning any maintenance or work on the pump e Inspect cord for damage before installation and or maintenance Replace the entire pump assembly if damage is found e Do not remove the grounding pin from the power cord plug e To reduce the risk of electric shock use only on portable self contained fountains no larger than 5 ft in any dimension
5. ctions e Remove the inlet screen and or front cover and impeller cover to expose the impeller Turn the impeller to ensure that it is not broken or jammed If the performance of the pump is not satisfactory or the pump does not flow evenly e Check to make sure the pump is completely submerged in water e Check to make sure the impeller and the impeller housing are clean REPLACEMENT PARTS LIST For replacement parts call our customer service department at 1 888 412 6001 8 a m 6 p m EST Monday Friday Description Extensions Extension tubes Waterspray nozzle Waterbell nozzle insert Trumpet nozzle insert lower fountain head nozzle Filter cover Pump with LED light Base plate Filter block Impeller cover O ring Shaft support Shaft Impeller assembly YOZA LQ TM O CO co Printed in China LIMITED WARRANTY All pumps and electrical products are warranted to the user against defective material and workmanship under normal working conditions This warranty period begins on the date of purchase by the original purchaser All TotalPond electrical products are warranted to the user against defective material and workmanship under normal working conditions for 1 year from the date of purchase All TotalPond liners are warranted to the user against defective workmanship under normal working conditions for 20 years from the date of purchase All other Tota
6. lPond product is warranted to the user against defective material and workmanship under normal working conditions for 90 days Application Warranty covers only properly installed and maintained units Pump warranty is limited to applications pumping fresh water in a pond or fountain only Other liquid applications or extreme temperature uses must be approved in writing by the manufacturer Receipt and product date code are required for warranty claims Warranty Claim Warranty claims must be made by calling customer service at 1 888 412 6001 If the item is determined to be defective you will be given authorization to return the defective part s freight pre paid along with proof of purchase Disposition The manufacturer will make a good faith effort for prompt disposition regarding all warranty claims Returned product will be inspected to determine cause of failure before warranty is applied Warranty does not cover any costs associated with the shipping handling installation or removal of products or parts subject to this warranty For products damaged in transit a claim should be filed with the carrier Disclaimer Any oral statements made about the product by the seller the manufacturer the representatives or any other parties do not constitute warranties should not be relied upon by the user and are not part of the contract for sale The sellers and manufacturer s only obligation and buyer s only remedy shall be for the
7. to use a sealant that is safe for clay pots Wait 24 j hours for the sealant to dry before filling the container with water Fig 4 Fig 4 Test fit the assembled container fountain kit in the container For installing the fountain with the pump cord over the side of the Cord container recommended proceed to step 9 For having the pump cord comes out through the container wall proceed to the next step Fig 5 D Select a spot on the container wall that is the least visible from normal viewing for the cord exit Drill a hole in appropriate 1 1 4 in diameter Fig 6 NOTE Appropriate safety equipment should be used 7 Place the pump inside the container and run the cord though the newly drill hole Seal the hole around the cord with epoxy putty and allow it to harden Fig 7 NOTE 1 Wearing gloves when mixing the putty is recommended NOTE 2 For best adhesion clean and roughen bond area NOTE 3 Cut off required epoxy putty Twist and knead until a uniform color is achieved no streaks Apply to the hole around the cord Working time is 15 minutes until hardening begins After approximately 1 5 hours the epoxy putty will fully harden Epoxy Putty Epoxy Putty 8 Test fit the assembled container fountain kit in the container Fill the container with water 2 3 up to the top Fig 8 9 If needed attach the extensions to the bottom of the filter box Fig 9 10 Connect the pump to a proper power source
Download Pdf Manuals
Related Search