Morton MCWF Instructions / Assembly
Contents
1. 6 Lay a piece of 2 inch thick board near the floor drain 7 Move the Whole Home Water Filtration System close to the drain Slowly and gently tip it over until the rim rests on the wood block with the inlet and outlet over the drain Do not allow the unit s weight to rest on the inlet and outlet fittings or they may break 8 Tip the bottom of the Whole Home Water Filtration System up a few inches and hold until all water has drained Leave the unit laying like this until you are ready to use it Plug the inlet and outlet with clean rags to keep dirt bugs etc out Drain all Water from Whole Home Water Filtration System Wood Block Floor Drain FIG 22 16 Morton Installation amp Operation Manual Troubleshooting PROBLEM CAUSE CORRECTION Water has black or NEW SYSTEM Start up procedure Run start up procedure See Page 13 or run gray color has not been completed consecutive Clean Rinse cycles See Page 14 Low water pressure at house faucets Water has objection able taste and or odor No water flow to drain during Clean Rinse cycle Clean Rinse cycle does not run automatically Clean Rinse cycle does not run at the pro grammed time of day Steady beeping from electronic control Error Code E1 E3 or E4 appears Error Code E5 appears NOT A NEW SYSTEM Normal abra sion of filtration media Sediment filter screen is clogged Filtration media pores are blocked Sys2. DOWN button CLEAN button When the power supply is plugged into the electrical outlet a model code and a test number example J2 0 begin to flash in the faceplate display Then 12 00 PM and the words PRESENT TIME begin to flash NOTE If shows in the display press the AA UP or V DOWN button until the model code CF 8 shows in the display Then press the PROGRAM button to set and change to the flashing PRESENT TIME display Model MCWF www systemsaver com 1 888 64WATER PROGRAM button FIG 11 Set Time of Day If the words PRESENT TIME do not show in the dis play press the PROGRAM button until they do 1 Press the A UP or V DOWN buttons to set the present time Up moves the display ahead down sets the time back Be sure AM or PM is correct Im AM III I PRESENT TIME PRESENT TIME FIG 12 NOTE Press buttons and quickly release to slowly advance the display Hold the buttons down for fast advance 2 Press the PROGRAM button a few times until the time appears on the display but is not flashing Questions Call Toll Free 1 888 64 WATER 1 888 649 2837 Monday Friday 8 AM 7 PM EST or visit www systemsaver com When you call please be prepared to provide the model and serial number located on the rating decal on back of the cover 12 Morton Installation amp Operation Manual Start Up IMPORTANT Run the start up cy
3. Model MCWF How to install operate and maintain your Whole Home Water Filtration System Do not return unit to store If you have any questions or concerns when in stalling operating or maintaining your Whole Home Water Filtration System call our toll free number 1 888 64 WATER 1 888 649 2837 Monday Friday 8 AM 7 PM EST or visit www systemsaver com When you call please be prepared to provide the model and serial number of your product located on the rating decal on back of the cover and certified to NSF ANSI Standard 372 System tested and certified by NSF International against NSF ANSI Standard 42 for the reduction of chlorine taste and odor Installation and Operation Manual 7339955 Rev C 4 11 14 TABLE OF CONTENTS Page Specifications amp Performance Claims LL 3 Dimensions refined aa 4 InspectShipmentir s fassa isti Mieli rio aria ad ti ese I 5 Before You start sirs ead asc esi li ARL ad leh ue den eee add Event hee tae 6 How a Whole Home Water Filtration System Works LL 6 Installation Requirements 7 9 Installation Instructions z sinaia a ae a ea E a e a E a EE e G aa aa a a a a A a S 10 11 Programming the Whole Home Water Filtration System 12 start Up Procedure vinerete Pi o a tal Aa e a a a ata ae ei usi eee ae 13 Customizing Features Options 14 15 Care of Your Whole Home Water Filtration System 16 Troubleshooting s resnais atelier i eb diate iaia 17 18 Whole H
4. ing to Waste Electrical and Electronic Equipment WEEE requirements This directive or similar laws are in place nationally and can vary from region to region Please refer to your state and local laws for In the state of Massachusetts The Commonwealth of Massachusetts plumbing code 248 CMR shall be adhered to A licensed plumber shall be used for this installation How a Whole Home Water Filtration System Works Normal Operation During normal operation water enters the Whole Home Water Filtration System and flows through several fil tration processes where tastes odors and sediment are reduced Clean Rinse Cycle A Clean Rinse cycle will automatically be initiated based on how the controller has been programmed The Clean Rinse cycle lifts and expands the media bed to rejuvenate the media and then repacks the bed for continued use During the Clean Rinse cycle dirt sediment etc are flushed from the Whole Home Water Filtration System down the drain Applications for a Whole Home Water Filtration System Do not use the Whole Home Water Filtration System with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system The Whole Home Water Filtration System may not be an effective treatment method for water sources with a hydrogen sulfide problem rotten egg odor or taste If your water has hydrogen sulfide contact a water treatment expert or call 1 888 64
5. then it is rec ommended that a minimum of 2 manually initiated Clean Rinse cycles be performed when the system is placed back into operation see Start a Clean Rinse Cycle section on Page 14 In any installation where there is a possibility of freezing the Whole Home Water Filtration System should be disconnected and the water drained see Protect the Whole Home Water Filtration System from Freezing section Protect the Whole Home Water Filtration System from Freezing If the Whole Home Water Filtration System is installed where it could freeze Summer cabin lake home etc you must drain all water from it to stop possible freeze damage To drain the unit 1 Close the shut off valve on the house main water pipe near the water meter or pressure tank 2 Open a faucet in the filtered water pipes to vent pressure in the unit 3 Move the stem in the single bypass valve to bypass Close the inlet and outlet valve in a 3 valve bypass system and open the bypass valve If you want water in the house pipes again reopen the shut off valve on the main water pipe 4 Unplug the power supply at the wall outlet Remove the cover Take off the drain hose if it will interfere with moving the Whole Home Water Filtration System into position over the drain 5 Remove the large holding clips at the Whole Home Water Filtration System inlet and outlet Separate the unit from the plastic installation adaptors or from the bypass valve
6. Percent Challenge Level Requirement Removal Chlorine 2 0 10 mg L 50 82 8 Questions Call Toll Free 1 888 64 WATER 1 888 649 2837 Monday Friday 8 AM 7 PM EST or visit www systemsaver com When you call please be prepared to provide the model and serial number located on the rating decal on back of the cover Morton Installation amp Operation Manual 3 Dimensions 36 1 8 27 SIDE VIEW FRONT VIEW FIG 1 Morton Installation amp Operation Manual Inspect Shipment The parts required to assemble and install the Whole Remove and discard or recycle all packing materials Home Water Filtration System are included with the To avoid loss of small parts we suggest you keep the unit Thoroughly check the Whole Home Water small parts in the parts bag until you are ready to use Filtration System for possible shipping damage and them parts loss Also inspect and note any damage to the shipping carton Packing List Installation Adaptors Drain Hose Clips including 1 spare Grommet used for Models Hose Clamps Adaptor Elbow M20 M27 M30 amp M34 FIG 2 Do not return the Whole Home Water Filtration System to store If you have any questions or there are missing parts or damage please call Toll Free 1 888 64 WATER 1 888 649 2837 Monday Friday 8 am 7 pm EST When you call please be prepared to provide
7. in a manual Clean Rinse mode See Operating in Manual Clean Rinse Mode section The automatic Clean Rinse function must be disabled if the Whole Home Water Filtration System will not be connected to a drain Connecting Valve to Drain Drain SUBSTITUTING RIGID DRAIN LINE a Fitting 1 4 NPT Threads GY Hose 1 2 Outside Dia Clamp Copper Tube not included Cut barbs from O drain fitting pull e clip to remove fit Cs To drain point other ting from valve Comp Fitting 1 4 O than floor drain NPT x 1 2 O D Support tubing in Tube not included n x place as needed N Re gt Valve Bue S Drain Hose Install adaptor elbow using hose clamp Aim noz 7 zle down toward Lala a center of drain Tie or wire tubing in 1 1 2 place air gap 3SSZ LAUNDRY TUB STANDPIPE Drain grate with 1 gt dia hole in center FLOOR DRAIN FIG 4 8 Morton Installation amp Operation Manual Installation Requirements Inlet Outlet Plumbing Options Always install either a single bypass valve provided to the contractor plumber supplied plumbing as shown in Figure 7 OR if desired a 3 valve bypass system parts not included can be installed as shown in Figure 6 Bypass valves allow you to turn off water to the Whole Home Water Filtration System for mainte nance if needed but still have water in house pipes Use either e Copper pipe Threade
8. that the Whole Home Water Filtration System is not damaged as the result of any unusual force of nature such as but not limited to flood hurricane tornado or earthquake Morton is excused if failure to perform its warranty obligations is the result of strikes government regulation materials shortages or other circumstances beyond its control THERE ARE NO WARRANTIES ON THE WHOLE HOME WATER FILTRATION SYSTEM BEYOND THOSE SPECIFICALLY DESCRIBED ABOVE ALL IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRAN TY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED TO THE EXTENT THEY MIGHT EXTEND BEYOND THE ABOVE PERIODS THE SOLE OBLIGATION OF MORTON UNDER THESE WARRANTIES IS TO REPLACE OR REPAIR THE COMPONENT OR PART WHICH PROVES TO BE DEFECTIVE WITHIN THE SPECIFIED TIME PERIOD AND MORTON IS NOT LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES NO MORTON DEALER AGENT REPRESENTA TIVE OR OTHER PERSON IS AUTHORIZED TO EXTEND OR EXPAND THE WARRANTIES EXPRESSLY DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty lasts or exclusions or limitations of inci dental or consequential damage so the limitations and exclusions in this warranty may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state This warranty applies to consumer owned installations only 2 Morton Installation amp Operation Manual Specifications
9. to the Whole Home Water Filtration System is lost memory built into the controller cir cuitry will keep all settings for several hours While the power is out the display is blank and the Whole Home Water Filtration System will not Clean Rinse When electrical power is restored you have to reset the time of day only if the display is flashing The Clean Rinse TIME never requires resetting unless a change is desired Even if the clock is incorrect after a long power outage the Whole Home Water Filtration System works as it should to keep your water treated However Clean Rinse cycles may occur at the wrong time of day until you reset the clock to the correct time of day NOTE If the Whole Home Water Filtration System was in a Clean Rinse cycle when power was lost it will now finish the cycle Morton Installation amp Operation Manual 15 Care of Your Whole Home Water Filtration System Vacations and Extended Periods of No Water Use If your Whole Home Water Filtration System will not be used for an extended period of time several months please follow one of these recommendations f the water supply to the unit is not turned off and the automatic Clean Rinse function has not been disabled then no further actions are required If the Clean Rinse cycle cannot be automatically run due to the water supply being shut off the power supply being unplugged or the automatic Clean Rinse function being disabled
10. with national state and local plumbing codes In the state of Massachusetts The Commonwealth of Massachusetts plumbing code 248 CMR shall be adhered to A licensed plumber shall be used for this installation Air Gap Requirements A drain is needed for Clean Rinse discharge water A floor drain close to the Whole Home Water Filtration System is preferred A laundry tub standpipe etc are other drain options Secure valve drain hose in place Leave an air gap of 1 1 2 between the end of the hose and the drain This gap is needed to prevent backflow of sewer water into the Whole Home Water Filtration System Do not put the end of the drain hose into the drain Requirements Valve Drain Requirements Using the flexible drain hose included measure and cut to the length needed Flexible drain hose is not allowed in all localities check your plumbing codes If local codes do not allow use of a flexible drain hose a rigid valve drain run must be used Purchase a com pression fitting 1 4 NPT x 1 2 in minimum tube and 1 2 tubing from your local hardware store Plumb a rigid drain as needed see Figure 4 below NOTE Avoid drain hose runs longer than 30 feet Make the valve drain line as short and direct as possible It is recommended that the Whole Home Water Filtra tion System be installed near a drain However if a drain is not available it is still possible to operate the Whole Home Water Filtration System
11. N button for a few seconds until RECHARGE NOW flashes in the display RECHARGE NO FIG 13 Set Number of Days Between Clean Rinse Cycles By default the Whole Home Water Filtration System will automatically initiate a Clean Rinse every 14 days This should be sufficient for most applications To change the number of days between Clean Rinse cycles 1 Press the PROGRAM button twice so RECHARGE is shown in the display FIG 14 2 Press the A UP or V DOWN buttons to set the number of days between Clean Rinse cycles from 1 to 99 3 Press the PROGRAM button twice when complete Set Clean Rinse Time By default the Whole Home Water Filtration System will Clean Rinse at 1 00 a m To change the Clean Rinse start time 1 Press the PROGRAM button three times so RECHARGE TIME is shown in the display RECHARGE TIME FIG 15 2 Press the UP or V DOWN buttons to set the Clean Rinse time Be sure AM or PM is correct 3 Press the PROGRAM button again when com plete Set Length of Clean Rinse By default the Whole Home Water Filtration System s Clean Rinse cycle will consist of a 2 minute back wash followed by a 1 minute fast rinse This should be sufficient for most applications Increasing the length of Clean Rinse time will increase the amount of water flushed to drain during each Clean Rinse cycle therefore these times should only be increased when necessary To chang
12. WATER The Whole Home Water Filtration System will not remove iron and is not intended to replace iron treatment equipment Although the Whole Home Water Filtration System has sediment filter capabilities additional sediment filtration may be needed in problem water applica tions 6 Morton Installation amp Operation Manual Installation Requirements Location Requirements Consider the following when selecting an installation location for the Whole Home Water Filtration System Do not operate the Whole Home Water Filtration System where freezing temperatures occur Do not attempt to treat water over 120 F Freezing temper atures or hot water damage voids the warranty To condition all water in the home install the Whole Home Water Filtration System close to the water supply inlet and before all other plumbing connec tions except outside water pipes e Fora home with municipal water supply install the Central Water Filtration System between the home s incoming water supply and the water softener if one is being used See Figure 3A If the home has well water reverse the order of the Central Water Filtra tion System and the water softener See Figure 3B A nearby drain is needed to carry away Clean Rinse discharge water Use a floor drain laundry tub sump standpipe or other options check your local codes See Air Gap Requirements and Valve Drain Requirements sections If a
13. amp Performance Claims This system has been tested according to NSF ANSI 42 for the reduction of chlorine taste and odor The concentra tion of the indicated substance in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system as specified in NSF ANSI 42 While testing was performed under standard laboratory conditions actual performance of the system may vary based on local water conditions SPECIFICATIONS Model MCWF Rated Service Flow Rate 6 0 gpm 22 7 L min Pressure Drop at Rated Service Flow 10 psig 68 9 kPa Pressure Drop at 9 6 gpm 15 psig 103 4 kPa ah NEI 30 125 psi Water Pressure Limits minimum maximum 206 8 861 8 kPa Water Temperature Limits minimum maximum 40 120 F 5 49 C Drain Flow Rate 3 4 gpm 0 50 ppm 2 280 000 gal 0 75 ppm 1 520 000 gal Rated Capacity at Chlorine Concentration of 1 0 ppm 1 140 000 gal 1 5 ppm 760 000 gal 2 0 ppm 570 000 gal Sediment Removal with 30 40 micron particle size 95 or more Sediment Removal with 40 50 micron particle size 99 or more From independent laboratory test data Typical residential chlorine concentration is 0 5 to 1 0 ppm This system conforms to NSF ANSI Standard 42 for the specific performance claims as verified and substantiated by test data PERFORMANCE CLAIMS Substance Influent Reduction Average
14. cle immediately after completing installation before using any water in the home The filtration media in this Whole Home Water Filtration System contains a small number of harmless activated carbon particles generated during shipping that are small enough to exit the system with water flow It is normal for these particles to cause a tempo rary discoloration of the water coming out of the sys tem To avoid discolored water at your home s faucets the system s start up cycle should be initiated to rinse the particles and any discolored water down the drain If the Whole Home Water Filtration System is used without first running the start up cycle you will notice that the water will temporarily have a gray color until the particles have exited the system To Initiate the start up cycle 1 Make sure the drain hose is attached to the Whole Home Water Filtration System and the other end is secured over a drain see Install Valve Drain Hose on Page 11 2 Make sure bypass valve is in the service open or filtered water position and the home s water supply is turned on 3 Press and hold the CLEAN button to initiate the start up cycle The button can be released when you hear the valve changing position and RECHARGE NOW flashes in the display Procedure During the start up cycle Throughout the start up cycle you will hear the valve changing position and notice the flow of water to drain starting and s
15. d pipe PEX Crosslinked Polyethylene pipe e CPVC plastic pipe Other pipe approved for use with potable water IMPORTANT Do not solder with plumbing attached to installation adapters and single valve bypass Soldering heat will damage the adapters and valve Cross Over In what direction does the water flow Be sure to plan piping so water flow is to the Whole Home Water Filtration System valve IN LET Plan a crossover if flow is from left to right Maj Treated Water from Untreated Valve Water to OUTLET Valve INLET To Whole Home 9 Water Filtration System FIG 5 x 3 Valve Bypass o S Sen T KM S 9 7 Whole Home Water 4 Filtration System OUTLET Whole Home Water Filtration System FIG 6 INLET Connecting Plumbing to Valve OUT IN 1 NPT Sweat Use Teflon tape Adapter 2 pipe joint com not included pound or both MA 1 NPT Adapter 2 apter 2 T ingudea Clip 4 Use Teflon tape pipe joint com pound or both 1 NPT Sweat Adapter 2 SS 2 not included Clip 2 1 NPT Adapter 2 Included Valve Inlet FIG 7 Morton Installation amp Operation Manual 9 Installation Instructions Step 1 Turn Off Water Supply 1 Close the main water supply valve near the well pump or water meter 2 Open all faucets to drain water from the house pipes NOTE Be sure not to drain water
16. drain is not available it is still possible to operate the Whole Home Water Filtration System in a manual Clean Rinse mode See Operating in Manual Clean Rinse Mode The automatic Clean Rinse must be disabled if the Whole Home Water Filtration System will not be connected to a drain See Page 8 The Whole Home Water Filtration System works on 28V DC electrical power supplied by a direct plug in power supply included Provide a 120V 50 60 Hz electrical outlet in accordance with NEC and local codes Do not install the Whole Home Water Filtration System on a hot water line See Figures 3A amp 3B below Avoid installing in direct sunlight Excessive sun heat may cause distortion or other damage to non metallic parts The Proper Order To Install Water Treatment Equipment Untreated Water to Cold Water to House Hot Water Z to House Outside Faucets City Water Supply Optional Aa Sediment dI Filter Water Water Heater Softener Untreated Water to Outside Faucets Cold Water to House Hot Water to House Optional Sediment Filter Whole Home Water Filtration FIG 3A System 4 OR Pressure Tank Water Whole Home Filtration System Water Heater Water Softener Morton Installation amp Operation Manual Installation Plumbing Codes AII plumbing must be completed in accordance
17. e the length of the backwash part of the Clean Rinse cycle 1 Press and hold the PROGRAM button for a few seconds until the 000 screen appears as shown in Figure 16 FIG 16 2 Press the PROGRAM button once so bA TIME appears in the display FIG 17 3 Press the A UP or V DOWN buttons to set the length of backwash in minutes 4 Press the PROGRAM button twice when complete To change the length of the fast rinse part of the Clean Rinse cycle 1 Press and hold the PROGRAM button for a few seconds until the 000 screen appears as shown in Figure 16 2 Press the PROGRAM button twice so Fr TIME appears in the display FIG 18 3 Press the A UP or V DOWN buttons to set the length of fast rinse in minutes 4 Press the PROGRAM button again when com plete 14 Morton Installation amp Operation Manual Customizing Features Options Operating in Manual Clean Rinse Mode Clean Rinse cycles will run automatically unless the automatic Clean Rinse function has been disabled If this function has been disabled it will be necessary to manually initiate any Clean Rinse cycles It is recom mended that a Clean Rinse cycle should be run at least once each month or more frequently if neces sary A manual Clean Rinse mode may be used when a drain required for automatic Clean Rinse is not available However it is recommended that automat ic Clean Rinse be used if t
18. from the water heater as damage to the water heater ele ments could result Step 2 Move the Whole Home Water Filtration System into Place 1 Move the Whole Home Water Filtration System into installation position Set it on a level surface If needed place the unit on a section of plywood a minimum of 5 8 thick Then place shims under the plywood to level the Whole Home Water Filtration System see Figure 8 Step 3 Complete Inlet and Outlet Plumbing Measure cut and loosely assemble pipe and fittings from the main water pipe to the inlet and outlet ports of the water softener valve Be sure to keep fittings fully together and pipes squared and straight Be sure hard water supply pipe goes to the water sof tener valve inlet side NOTE Inlet and outlet are marked on the water sof tener valve Trace the water flow direction to be sure hard water is to inlet IMPORTANT Be sure to fit align and support all plumbing to prevent putting stress on the water softener valve inlet and outlet Undue stress from misaligned or unsup ported plumbing may cause damage to the valve Complete the inlet and outlet plumbing for the type of pipes you will be using Step 4 Cold Water Pipe Grounding CAUTION The house cold water pipe metal only is often used as a ground for the house electrical system The 3 valve bypass type of installation shown in Figure 6 will maintain ground continuity If you use a plastic bypass va
19. he drain requirements can be met IMPORTANT During the Clean Rinse cycle whether manually or automatically initiated water will flow from the valve drain port If a permanent drain line has not been installed provisions must be made for the drain flow prior to initiating a Clean Rinse cycle DISABLING AUTOMATIC CLEAN RINSE To disable the automatic Clean Rinse function 1 Press and immediately release the CLEAN button pressing and holding the button a few seconds would initiate a Clean Rinse cycle 2 VAC should flash in the display as shown in Figure 19 indicating that the Whole Home Water Filtration System is in the manual Clean Rinse mode the automatic Clean Rinse function has been dis abled FIG 19 MANUALLY STARTING A CLEAN RINSE CYCLE To manually start a Clean Rinse cycle 1 Press and hold the CLEAN button for a few sec onds until RECHARGE NOW flashes in the display as shown in Figure 20 WI RECHARGE NOW FIG 20 2 When the Clean Rinse cycle is complete the Whole Home Water Filtration System will remain in the manual Clean Rinse mode RE ENABLING AUTOMATIC CLEAN RINSE To return the Whole Home Water Filtration System to its automatic Clean Rinse function 1 Press and immediately release the CLEAN button 2 The flashing VAC on the display should be replaced by the normal time of day screen as shown in Figure 21 FIG 21 Power Outage Memory If electrical power
20. ing non bypass position Clean drain flow control See Page 18 Straighten drain hose Check for loss of power and correct Press and release the CLEAN button until display no longer reads VAC Check for loss of power Reset the clock to the correct time of day See Page 12 Allow 48 hours for board to dry or use blow dryer Replace wiring harness or connection to position switch See parts list at end of this manual Replace switch See parts list at end of this manual Replace rotor seal kit instructions included with kit Replace motor instructions included with motor Replace electronic control board PWA instruc tions included with PWA Need help troubleshooting Call Toll Free 1 888 64 WATER 1 888 649 2837 Monday Friday 8 AM 7 PMEST or visit www systemsaver com When you call please be prepared to provide the model and serial number located on the rating decal on back of the cover Morton Installation amp Operation Manual 17 Troubleshooting Procedure for removing error code from display 1 Unplug power supply from electrical outlet 2 Correct problem 3 Plug power supply back in 4 Wait 8 minutes The error code will return if the problem was not corrected Assistance from customer service may be needed with the following PROBLEM CAUSE CORRECTION Water running to the drain while unit is not in the Clean Rinse cycle plumbing Reset
21. lve at the unit continuity is broken To restore the ground do the following Level if Necessary Plywood FIG 8 Ground Wire FIG 9 1 Install a 4 copper wire across the removed section of main water pipe securely clamping it at both ends See Figure 9 parts not included NOTE Check local plumbing and electrical codes for proper installation of the ground wire The installation must conform to them In Massachusetts plumbing codes of Massachusetts shall be conformed to Consult with your licensed plumber 10 Morton Installation amp Operation Manual Installation Instructions Step 5 Install Valve Drain Hose Single Bypass Valve NOTE See valve drain options on page 8 Drain Line 1 Measure cut to needed length and connect the 3 8 ened drain line provided to the Whole Home Water Filtration System valve drain fitting See Figure 10 Use a hose clamp to hold the hose in place IMPORTANT If codes require a rigid drain line see Valve Drain requirements section 2 Run the drain hose or copper tubing to the floor drain Secure drain hose This will prevent the drain line from whipping during Clean Rinse cycles See Air Gap Requirements section Step 6 Test for Leaks 1 Make sure the single bypass valve or 3 valve bypass if installed is in the bypass position with the handle pu
22. ome Water Filtration System Components 20 23 MORTON RESIDENTIAL WARRANTY Morton guarantees to the original owner that e For a period of ten 10 years from the date of purchase the fiberglass filtration media tank will not rust corrode leak burst or in any other manner fail to perform its proper functions e For a period of one 1 year from the date of purchase all other parts will be free of defects in material and workmanship and will perform their normal functions If during such respective period a part proves to be defective Morton will ship a replacement part directly to your home without charge Labor necessary to maintain this product is not covered by the product warranty If you have questions regarding a Morton product need assistance with installation or troubleshooting wish to order a part or report a warranty issue we are just a phone call away Simply dial 1 888 64 WATER 1 888 649 2837 for assistance or visit www systemsaver com This Whole Home Water Filtration System is manufactured for Morton P O Box 25290 Woodbury MN 55125 0290 General Provisions The above warranties are effective provided the Whole Home Water Filtration System is operated at water pressures not exceeding 125 psi and at water temperatures not exceeding 120 F provided further that the Whole Home Water Filtration System is not subject to abuse misuse alteration neglect freezing accident or negligence and provided further
23. r visit www systemsaver com When you call please be prepared to provide the model and serial number located on the rating decal on back of the cover 18 Morton Installation amp Operation Manual Notes Morton Installation amp Operation Manual 19 Whole Home Water Filtration System Exploded View Valve Assembly See Pages 22 amp 23 for parts 20 Morton Installation amp Operation Manual Whole Home Water Filtration System Parts List Key No Description 7311038 Assembly Replacement Mineral Tank w media amp asso ciated components Includes Key Nos 1 through 13 711296 Distributor O Ring Kit includes Key Nos 1 3 O Ring 2 7 8 x 3 1 4 O Ring 13 16 x 1 1 16 726502 Filter Screen 7105047 Repl Bottom Distributor 7331177 Tank Neck Clamp Kit includes 2 ea of Key Nos 7 amp 8 7 a M 1 O Ring 2 3 4 x 3 Top Distributor 5 7310781 Drain Hose 20 ft 20 21 iii H Not illustrated Mineral Tank and media can only be purchased as part of the Replacement Mineral Tank Assembly See top of list Lo Ete dee ied o Aaivated Carbon fol Fiersa ss OOOO a Greve gt fo Cro F 14 p it Retainer Clip 2 req lamp Section 2 req Mineral Tank 8 x 25 3 7077870 2 ai 6 i E e 0 ae Ea ELE Questions Call Toll Free 1 888 64 WATER 1 888 649 2837 Monday Friday 8 AM 7 PM EST or vi
24. shed in See Figure 10 2 Fully open the main water supply valve 3 Briefly open a faucet in the house to refill the plumb ing with water 4 Slowly move the bypass valve s to the normal operation position pausing several times to allow the unit to pressurize slowly See Figure 10 5 Check for leaks at all the plumbing connections you made IMPORTANT Start up procedure must be run prior to using any filtered water Follow the instructions below and on Page 13 Step 7 Turn On the Whole Home Water Filtration System During installation the Whole Home Water Filtration System wiring may be moved or jostled from place Check to be sure all leadwire connectors are secure on the back of the electronic board and be sure all wiring is away from the valve gear and motor area which rotates during Clean Rinse cycles 1 Plug the Whole Home Water Filtration System s power supply into an electrical outlet that is not con trolled by a switch 2 In the display the words PRESENT TIME appear and 12 00 PM begins to flash Set the clock accord ing to the Set Time of Day section on Page 12 3 Run the start up procedure as detailed on Page 13 Pull handle OUT for normal operation _ a Push handle IN for BYPASS FIG 10 Morton Installation amp Operation Manual 11 Programming the Whole Home Water Filtration System Display hole Home Water Filtration System UP button
25. sit www systemsaver com When you call please be prepared to provide the model and serial number located on the rating decal on back of the cover Morton Installation amp Operation Manual 21 Valve Assembly Exploded View Wear Strip Seal By Cross section View 22 Morton Installation amp Operation Manual Valve Parts List Screw 6 19 x 1 3 8 2 req IU 7331274 Drain Hose Adaptor Kit incl Key Nos 55 59 7129716 Seal Kit includes Key Nos 60 65 Co orme 66 7062067 WaveWasher SSCS 7109232 7842666 Drain Plug Kit 314 includes Key Nos 64 68 amp 69 se a Pwebranse CS se a om OOO 7342673 Installation Adaptor 3 4 pack of 2 including 2 ea Clips amp O Rings See Key Nos 70 amp 72 Questions Call Toll Free 1 888 64 WATER 1 888 649 2837 Monday Friday 8 AM 7 PM EST or visit www systemsaver com When you call please be prepared to provide the model and serial number located on the rating decal on back of the cover Morton Installation amp Operation Manual 23
26. tem is in bypass Filtration media pores are blocked System is in bypass Drain flow control is plugged Drain hose is plugged or kinked Power supply is unplugged from wall electrical outlet display will be blank If display reads VAC then Clean Rinse function has been disabled If display is blank power supply may be unplugged from wall electrical outlet If time display is flashing then a long power loss caused the clock to lose its time setting Electronic control board is wet Fault in wiring harness or connections to position switch Fault in switch Fault in valve causing high torque Motor inoperative Electronic control until water color returns to normal Manually initiate a Clean Rinse cycle See Page 14 Manually initiate a Clean Rinse cycle See Page 14 If the filter screen is frequently plugging it may be necessary to adjust the frequency of Clean Rinse cycles or add a sediment filter upstream See Figure 3 on Page 7 Manually initiate a Clean Rinse cycle See Page 14 If the filtration media pores are frequently block ing it may be necessary to increase the frequen cy of Clean Rinse cycles Move bypass valve s to normal operating non bypass position Manually initiate a Clean Rinse cycle See Page 14 If the filtration media pores are frequently block ing it may be necessary to increase the frequen cy of Clean Rinse cycles Move bypass valve s to normal operat
27. the model and serial number found on the rating decal on back of the cover For more installation or service information visit www systemsaver com Morton Installation amp Operation Manual 5 Before You Start Use care when handling the Whole Home Water Filtration System Do not turn upside down drop or set on sharp protrusions The Whole Home Water Filtration System has a maximum allowable inlet water pressure of 125 psi and a mini mum of 30 psi If daytime pressure is over 80 psi nighttime pressure may exceed the maximum Use a pressure reducing valve if necessary Adding a pressure reducing valve may reduce the flow If your home is equipped with a back flow preventer an expansion tank must be installed in accordance with local codes and laws The Whole Home Water Filtration System works on 28V DC electrical power supplied by a direct plug in power supply included Be sure to use the included power supply and plug it into a nominal 120V 50 60 Hz house hold outlet that is in a dry location only grounded and properly protected by an overcurrent device such as a cir cuit breaker or fuse e Do not use the Whole Home Water Filtration System with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system ay European Directive 2002 96 EC requires all electrical and electronic equipment to be disposed of accord ps proper disposal of this equipment
28. ting to Factory Defaults To reset the electronic controller to its factory default for all settings time number of days between Clean Rinse cycles etc 1 Press the PROGRAM button and hold it until the display changes twice to show CODE and the flashing model code 2 Press the A UP button twice to display a flashing Sos 3 Press the PROGRAM button and the electronic controller will restart 4 Set the present time as described on page 12 Cleaning the Drain Flow Control This procedure is not required if the Whole Home Water Filtration System is operating normally It should be performed only if a problem with lack of water flow to drain is encountered as detailed in the troubleshooting table on Page 17 1 Remove the clip holding the drain fitting into the valve See Figure 24 Remove the drain fitting from the valve Clear any obstruction Reinstall the drain fitting into the valve a fF O N Reinstall the clip to secure the drain fitting in the valve Inner valve defect causing leak Filter media in household Crack in distributor or riser tube Replace seals and rotor Replace distributor or riser tube CODE 201 FIG 23 Removing Drain Fitting to Clean Flow Control Flow Clip Control Hose Drain Clamp Hose Fitting FIG 24 Need help troubleshooting Call Toll Free 1 888 64 WATER 1 888 649 2837 Monday Friday 8 AM 7 PM EST o
29. topping The start up cycle will take approximately 20 minutes Avoid using water during this time Do not set the time of day or press other buttons during the start up cycle as this will interrupt the start up cycle Do not unplug the power supply during the start up cycle If the start up cycle is inter rupted it should be initiated again and allowed to run to completion After the start up cycle Once the start up procedure completes successfully it cannot be initiated a second time The Whole Home Water Filtration System will automatically return to the normal operation position Once the start up cycle has run a faucet in the home should be opened and water allowed to run for 10 minutes at the system s rated flow If after running the start up cycle the water still appears discolored manually run Clean Rinse cycles See Page 14 until the water is clear If the time of day was not set before the start up cycle set it now See Page 12 Check the new plumbing connections and joints once more for leaks Questions Call Toll Free 1 888 64 WATER 1 888 649 2837 Monday Friday 8 AM 7 PM EST or visit www systemsaver com When you call please be prepared to provide the model and serial number located on the rating decal on back of the cover Morton Installation amp Operation Manual 13 Customizing Features Options Start a Clean Rinse Cycle To manually start a Clean Rinse cycle press and hold the CLEA
Download Pdf Manuals
Related Search