Design House 545863 Instructions / Assembly
Contents
1. 31 Spray seat Aerator shell Escutcheon Screw Baseplate Mounting nut Mounting stud Body Selector valve Stator Screw O ring Copper tube H 30 Spray connect Copper tube C 34 Hose Assembly 32 Mounting nut INSTALLATION PROCEDURE 1 Shut off water supplies Remove old faucet Clean sink surface in preparation for new faucet 2 Place base plate under escutcheon Insert mounting stud through left and right holes into escutcheon Position faucet on sink From underneath the sink install mounting nuts onto screws and tighten to hold faucet securely in place 3 Install sprayer optional After faucet is installed position sprayer support in far right hole in sink Insert spray hose down through the seat Secure the sprayer seat to the sink by threading the lock nut onto the mounting stud Hand tighten the lock nut onto the spray seat Under the sink connect the spray hose to the connection on faucet 4A Stainless Steel Braided Faucet Supply Tubes This is the simplest of all installations If you are using stainless steel braided faucet supply tubes this faucet requires one end of the supply tube to have a 1 2 female IPS connection The other end of this supply tube must match the thread on the water supply fittings or shut off valve under your sink Once you have identified the required tube carefully follow the manufacturer s installation instructions for each tube Note when lookin2. Your new faucet is made in strict compliance with all government standards The materials used in the manufacture of this faucet are of industry standard quality and are similar to other plumbing products having brass fittings To reduce the amount of lead in your drinking water allow the water to run for a moment before filling your glass and remember to always use cold water for drinking purposes
3. Design House is a registered brand of DHI Corp Mequon WI 53092 l DESIGNHOUSE el MIDDLETON SINGLE HANDLE KITCHEN FAUCET WITH SIDE SPRAY Models 545863 545855 545848 Your new Design House faucet will give you years of trouble free performance Thank you for choosing our product for yourhome Please read all of these instructions carefully before installing your new faucet Helpful tools to install this faucet Basin Wrench Adjustable Wrench Teflon Tape Silicone Sealant Pipe Wrench Screwdriver Flexible Water Plumber s Putty Supply Line Warning Avoid contact of plastic parts with plumber s putty pipe dope or any other oil based compound Use a silicon acrylic or latex based sealant where needed IMPORTANT POINTS When installing your new faucet first hand tighten the connector nuts then use one wrench to anchor the fitting and a second wrench to tighten the nut one additional turn Connections that are too tight will reduce the integrity of the system Wrap threaded connections except aerator thread in spout or where o ring or rubber sealant are present with Teflon tape available from your local hardware or plumbing supply store Always wrap in a clockwise direction SAFETY TIPS ALWAYS protect your eyes with safety glasses Handle Screw Color Button Bonnet Adjusting nut Sprayer hu Block Ball Valve seal Ball Valve Sealing gasket Sealing spring Washer Spout Washer Aerator
4. g at the faucet the left pipe is the Hot water side the right pipe is the Cold water side 4B Flexible Supply Lines with 3 8 OD Flexible Supply Lines with 3 8 OD If you are using flexible supply lines to connect the faucet to the water supply slip the coupling nut behind the ball nose of the flexible supply tube The ball nose will go partially into IPS shank or fitting Tighten the coupling nut DO NOT OVER TIGHTEN Install the opposite end to your water supply according to the manufacturer s instructions for both tubes Note when looking at the faucet the left pipe is the Hot water side the right pipe is the Cold water side 5 Important After installation is completed remove aerator Turn on water supply and allow both hot and cold water to run for at least one minute each While water is running check for leaks Re install aerator Do not overtighten MAINTENANCE Your new Design House faucet is designed to give you years of trouble free performance Keep it looking new by cleaning it periodically with a soft cloth Avoid abrasive cleaners steel wool and harsh chemicals as these will dull the finish and void your warranty Brass finishes are polished then protected with a lacquer coating to help prevent tarnishing Clean these surfaces only with a damp soft cloth CONSUMER PROTECTION WARNING Under the Safe Drinking Water Act the U S Environmental Protection Agency restricts the amount of lead used in brass and solder
Download Pdf Manuals
Related Search