Glacier Bay HDGEFS4 Use and Care Manual
Contents
1. 1Micron is equivalent to micrometer u m 2Milligrams per liter which is equivalent to parts per million PPM 3Acceptance level for this substance is based on percent reduction rather than maximum effluent concentration Particles per milliliter Environmental Protection Agency maximum contaminant level as required under the Safe Drinking Water Act 5 HOMEDEPOT COM GLACIERBAY Please contact 1 800 247 1087 for further assistance Pre Installation continued TOOLS REQUIRED PACKAGE CONTENTS Wrench Sealant tape Part Description Quantity Filtration system Mounting bracket with 2 screws Adaptor 1 in male NPT thread Clip m oO oO wo gt Vent tube e N de e Installation Attaching the adaptors and clips to the filter o Insert the adaptors C into the holes on each side of the filter head A o Secure in place with the clips D Ensure all three tabs of the clips D go through the matching holes and fully into the channels on the adaptor C Outside diameter Outside diameter of Filtration of clip channel on System Head Adaptor 2 Mounting the filter IMPORTANT To operate properly you must install this filtration system in a vertical orientation The filtration system must also be installed with the water flow following the arrows on the filter s inlet and outlet This corresponds to a left to right fl2. clamps and a 4 copper wire per To filter all household water install this home water filtration system on the household s main incoming water pipe For a home with municipal water supply install the filter between the home s incoming water supply and the water softener if a water softener is being used See Fig 1 If the home has well water reverse the order of the filter and the water softener See Fig 2 Untreated Water to Outside Faucets Cold Water Z to House City Water Supply Hot Water to House Whole Home Filtration System a Fig 1 Water Water Softener Heater OR 4 Untreated Water to Outside F t SIRS Taupa Cold Water _ to House d Pressure Hot Water Tank to House Whole Home Filtration System Well Water Supply Se Heater Fig 2 In some cases it may be necessary for plumbing to cross over to ensure the correct flow direction through the filter ooo _ Pre Installation continued DIMENSIONS Outlet 1 in NPT 7 1 2 in la 14 in red SPECIFICATIONS Rated Service Flow Rate 60 psi 414 kPa 9 0 gpm 34 0 L min Pressure Drop 30 psi 207 kPa 2 psig 13 8 kPa Water Pressure Limits minimum maximum 30 100 psi 207 689 kPa Water Temperature Limits minimum maximum 40 100 F 5 38 C PERFORMANCE CLAIMS Read this performance data and c
3. direct sunlight Excessive sun heat may cause distortion or other damage to nonmetallic parts NOTICE This filtration system works on water pressures of 30 psi minimum to 100 psi maximum If your house water pressure is over the maximum install a pressure reducing valve in the water supply pipe to the filtration system NOTICE All plumbing codes must be completed in accordance with national state and local plumbing codes Local code information can be obtained at your local public works department NOTICE In the state of Massachusetts The Commonwealth of Massachusetts plumbing code 248 CMR shall be adhered to A licensed plumber shall be used for this installation GROUNDING INFORMATION METAL PLUMBING INSTALLATIONS WARNING ELECTRICAL SHOCK HAZARD Prior to installation on metallic plumbing securely install two A grounding clamps and a 4 copper wire per installation instructions Failure to follow these instructions can result in death or electrical shock The house main incoming water pipe is often used to ground electrical outlets in the home Grounding protects you from electrical shock Installing the water filtration system may break this ground Before beginning installation purchase and securely install two grounding clamps and a 4 copper wire across the location where the filter will be tightly clamping it at both ends as shown below Ground Wire not i
4. surface before opening it Unsnap the lid clamp by pulling its latches in opposite directions Do not pry or use tools as this may damage the assembly Pull latches in opposite directions to unsnap Top view of lid 4 Swing the clamp halves open and lift the lid assembly up off the filter cartridge and sump A NOTE Do not remove the pin that holds the clamp halves to the lid 9 HOMEDEPOT COM GLACIERBAY Please contact 1 800 247 1087 for further assistance Filter Cartridges continued 5 Remove the used filter cartridge from the sump If you have difficulty removing the cartridge from the sump insert a screwdriver into the slot and pry up Dispose of the used cartridge properly A NOTE Check the sump to ensure it is dry and free of debris 6 Take the new filter cartridge out of its packaging and remove the protective caps from the ports Filter cartridges can only be installed in one orientation and are keyed to assure proper fit Insert the new filter cartridge into the sump and turn it until the triangular points on its top edge align with and drop into the corresponding detents in the sump A Align filter cartridge OP in sump using these TO triangular points Remove protective caps from filter cartridge ports 7 Slide the lid assembly down over the replacement cartridge s ports until it sits flat on top of the sump then lock the clamp onto the sump by pinching toget
5. the adaptor at the O rings The O ring is damaged Inspect and replace the O ring if damaged Water drips from the outlet side Water is flowing back Ensure the vent hose is not elevated above the of the filter head near the vent through the vent hose filter head tube Replacement Parts Key No Part No Description 1 1073 21 HA Head Assembly 2 1042 32 HE Mounting Bracket 3 1042 32 HE Mounting Screw 2 4 1042 32 HB Installation Adaptor Elbow 1 NPT including o rings 2 5 1042 32 HB Clip 2 6 1042 32 HD Lid amp Clamp Assembly 7 1042 32 HC Sump 8 1042 32 47 Vent Tube 6 ft long g HDGEFF4 Replacement Filter Purchase replacement filter cartridges from your local The Home Depot store To order replacement parts call 1 800 247 1087 7 a m 6 p m CST Monday Friday 11 HOMEDEPOT COM GLACIERBAY Please contact 1 800 247 1087 for further assistance GLACIER BAY Questions problems missing parts Before returning to the store call Glacier Bay Customer Service 7 a m 6 p m CST Monday Friday 1 800 247 1087 HOMEDEPOT COM GLACIERBAY Retain this manual for future use Manufactured by Ecodyne Water Systems 1890 Woodlane Drive Woodbury MN 55125
6. Item 1000 991 173 GLACIER BAY PATES USE AND CARE GUIDE PREMIUM HOUSEHOLD WATER FILTRATION SYSTEM System tested and certified by NSF Interna tional against NSF ANSI Standard 42 for particulate class III reduction Questions problems missing parts Before returning to the store call Glacier Bay Customer Service 7 a m 6 p m CST Monday Friday 1 800 247 1087 HOMEDEPOT COM GLACIERBAY 201 8401460 rev 00 THANK YOU We appreciate the trust and confidence you have placed in Glacier Bay through the purchase of this filtration system We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Glacier Bay Table of Contents Safety Information 2 WAIlTANty esesseeeseeeesteesseesseesteenseeesees Pre Installation Pre Installation INspection Installation Location Dimensions Specifications Performance Claims Tools Required Safety Information Onna W Package Content sccsssssseeseeeeeseeee 6 Installation Filter Cartridges Filter Cartridge Life Filter Cartridge Replacement Troubleshooting ssseseeseeeseesees Replacement Parts sscssesseseeee Read all instructions before installing and using your home water filtration system Follow all steps exactly to correctly install Rea
7. ding this manual will also help you to get all the benefits from the filtration system This system has been tested according to NSF ANSI Standard 42 for particulate class III reduction 5 micron to less than 15 micron The concentration of the indicated substance in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system as specified in NSF ANSI 42 The testing was performed using spiked tap water at a flow rate of 4 GPM 15 2 L min pH of 7 5 0 5 pressure of 60 PSIG and temperature of 68 5 F All plumbing must be completed in accordance with national state and local plumbing codes Local code information can be obtained at your local public works department In Massachusetts plumbing code 248 CMR 3 00 and 10 00 shall be adhered to Consult with your licensed plumber To condition all water in the home install the filtration system close to the water supply inlet and before all other plumbing connections except outside water pipes WARNING Do not use with water that is A microbiologically unsafe or of unknown quality without adequate disinfection before or after the system CAUTION Do not install the filtration system outside or in extreme hot or cold temperatures Temperature of A the water supply to the filtration system must be between 40 F and 100 F Do not install on a hot water line CAUTION Avoid installing in
8. her the latches until they snap The clamp will not snap unless the cartridge and sump are properly seated and aligned Sy Lid assembly Filter cartridge 8 Insert the sump assembly into the head by guiding the filter ports into the corresponding receptacles in the head and pushing the sump upward until it stops i Insert ports and Pivot sump down Pinch latches push sump up to service together to snap lt into filter head position A until seated Se s S Ne g AM ol 9 Pivot the sump all the way down to the service position 10 Some types of filter cartridges contain activated carbon a black powder Open a faucet downstream from the filter to purge air and fine carbon particles from the cartridge Flush for at least 5 minutes 10 Troubleshooting Problem Possible Cause Solution The replacement filter cartridge The filter cartridge is not Reorient the filter cartridge does not fit in the filter sump properly oriented The lid does not fit on the filter The filter cartridge is not properly oriented Reorient the filter cartridge The lip clamp cannot be latched The filter cartridge is not properly oriented Reorient the filter cartridge Water leaks from the adaptor at the threads The seal in the threads is inadequate threads Reinstall the adaptor with adequate Teflor tape or plastic compatible pipe sealant on the Water leaks from
9. incurred during installation repair or replacement nor for incidental or consequential damages Some states provinces and nations do not allow the exclusion or limitation of incidental or consequential damages so the above exclusions or limitations may not apply to you Glacier Bay Water Filtration Systems will advise you of the procedure to follow in making warranty claims Simply write to Glacier Bay Water Filtration Systems at the address below Explain the defect and include proof of purchase and you name address and telephone number or you can also call us at 1 800 247 1087 U S A Canada Glacier Bay Water Filtration Systems Glacier Bay Water Filtration Systems 2455 Paces Ferry Road N W 900 1 Concorde Gate Atlanta GA 30339 4024 Toronto ON M3C 4H9 3 HOMEDEPOT COM GLACIERBAY Please contact 1 800 247 1087 for further assistance Pre Installation PRE INSTALLATION INSPECTION Thoroughly check the water filtration system for possible shipping damage and parts loss Also inspect and note any damage to the shipping carton Remove and discard or recycle all packing materials To avoid loss of small parts we suggest you keep the small parts in the parts bag until you are ready to use them INSTALLATION LOCATION installation instructions Failure to follow these instructions can result in death or electrical shock A WARNING Electrical Shock Hazard Prior to installation on metallic plumbing securely install two grounding
10. ncluded Clamp 2 not included Warranty Glacier Bay Water Filtration Systems Warranty Glacier Bay Water Filtration Systems are manufactured under the highest standards of quality and workmanship Glacier Bay Water Filtration Systems warrants to the original purchaser that this system will be leak and drip free during normal domestic use for a period of one 1 year from date of purchase If this system should ever develop a leak or drip Glacier Bay Water Filtration Systems will free of charge provide the parts necessary to put the system back in good working condition A replacement for any defective part will be supplied free of charge for installation by the purchaser Defects or damage caused by use of other than authorized parts are not covered by this warranty This warranty shall be effective from date of purchase as shown on purchaser s receipt Glacier Bay Water Filtration Systems shall be installed per the manufacturer s installation instructions and specifications Some states do not allow limitations on how long a warranty lasts so the above limitation may not apply to you This warranty is valid for the original purchaser only and excludes industrial commercial or business use of the product product misuse and product damage due to installation error whether performed by a contractor service company or yourself Glacier Bay Water Filtration Systems will not be responsible for labor charges or for damage
11. ompare the capabilities of this unit with your actual water treatment needs It is recommended that before purchasing a water treatment unit you have your water supply tested to determine your actual water treatment needs This filter system is designed to be used for the reduction of the performance claims listed below Do not use where water is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system While testing was performed under standard laboratory conditions actual performance of the system may vary based on local water conditions Some or all of the contaminants reduced by this unit may not be in your water supply See elsewhere in this manual for further instructions on system installation operating procedures filter cartridge replacement and warranty The maintenance instructions must be followed for the product to perform as indicated below Filter cartridges should be replaced every six months Replacement filter cartridges are available at your nearest The Home Depot store A NOTE Current pricing of replacement filter cartridge is approximately 30 00 to 60 00 Substance Required NSF Min Average Avg Max Avg Min EPA Max Influent Level Reduction influent Level Effluent Level Percent Contaminant Requirement Removal Level5 Particulates 10 000 85 180 000 26 45 99 9 99 9 None Class III mg L particles mL particles mL 5 to lt 15 micron
12. ow when looking at the front of the filter head assembly o Use the included screws to mount the mounting bracket B to a strong and stable surface that can support up to 15 Ibs Allow for a few inches of space under the sump of the filter A to allow you to grasp and pivot it outward when replacing filter cartridges o Mount the filter A to the bracket B using the four notches on the bracket When mounted the filter should be aligned with the inlet and outlet plumbing and not cause rigid pipes to distort B A N d fg P 1 7 3 16 in N A HOMEDEPOT COM GLACIERBAY Please contact 1 800 247 1087 for further assistance Installation continued 3 Connecting the water supply lines A Installing the vent tube while attached to plastic installation adaptors Solder heat will damage the adaptors IMPORTANT Do not solder the metal plumbing IMPORTANT The vent tube works using gravity Do not elevate it above the vent port Route it downward to the drain point with no humps dips or loops o Seal the inlet 1 and outlet 2 threads of the filter adaptors with several wraps of sealant tape o Connect the water supply lines to the inlet 1 and outlet 2 adaptors using 1 in female NPT threaded adaptors not included Use caution to avoid cross threading the adaptors Note flow direction arrows on filter o Press the end of the vent tube E firmly over the ba
13. rbed fitting 1 on the filter o Route the vent tube E down to a floor drain laundry tub or other suitable drain point Filter Cartridges USE GLACIER BAY REPLACEMENT FILTER HDGEFF4 FILTER CARTRIDGE LIFE Replace the filter cartridge every six months There are several variables that determine how long a cartridge will last These include 1 How much water you use and 2 How much sediment taste and or odor or other unwanted substance is in the water You will know it is time to replace the cartridge when you first notice the return of the unwanted sediment taste and or odor in your water or when the flow diminishes or stops FILTER CARTRIDGE REPLACEMENT NOTE Itis not necessary to shut off the water supply when replacing the filter cartridge 1 Grasp the lower part of the sump and pull it firmly and slowly toward you pivoting upward until it stops in the bypass filter change position You may notice a hissing sound as a small amount of water approximately 4 ounces is expelled into the vent tube to relieve pressure in the sump l i Pull sump Pivot sump down to up to bypass remove position from head 2 Pull the sump downward out of the head To avoid unintended water flow from the filter head do not pivot the filter head down to the service position without the sump and replacement filter cartridge in place 3 Take the sump assembly to a sink or level waterproof
Download Pdf Manuals
Related Search