Swanstone WB00000SB.010 Installation Guide
Contents
1. CENTER LINE CENTER LINE BACK SWANSTONE Strength Balance Beauty Installation Care and Cleaning Model WB 2218 Palladio Tools Required e Ruler Tape Measure NOTE e Drill DEPENDING ON THE SURFACE THAT YOU WILL BE MOUNTING You will need tools required to install a faucet Check the faucet manufacturer s installation procedure If e Masking Tape THIS PRODUCT INTO YOU WILL NEED THE NECESSARY TOOLS you will be mounting the faucet into the Swanstone you will need a 1 4 drill bit and a 1 1 4 router spade e Safety Glasses REQUIRED TO CUT INTO THAT SURFACE bit twist drill or hole saw e Screwdriver e Saber Saw e Caulk Silicone Adhesive Instructions For Drilling Into The Swanstone Product Cut Out Area Drill Starter Hole sane Inside of Cut Out hs f If you will be installing a faucet Area ee lt into this Swanstone product a T model WB 2218 you will need to follow this procedure The Swanstone bowl comes with standard hole patterns Locate MASKING TAPE 1 Cut out the inside of the template 2 Drill a starter hole inside of the 3 Using a saber saw cut inside of the desired drill points and with Locate the template front to rear and cutout line the cutout line Trial fit to check for a 1 4 bit drill a pilot hole from right to left on the countertop Make proper fit the underside sure that the bowl location will not interfere with the cabinet below or the Drill fixture holes from the top plumbing At2. h disappears NOTE FOR SWANSTONE GRANITES use 9 Fine Finishing Film for final blending Use Paste Wax to restore color Use of these products will not damage the Swanstone solid surface Always follow label directions If these methods fail to produce acceptable results contact the Swan representative in your area The Swan Corporation One City Centre Suite 2300 St Louis MO 63101 800 325 7008 Form 852 6 05 00M Te i en a ty an iS it a pa a S E S a a a a a e p i a J oa a A a ae p S a a a E a a S R a S e a a pa a j F R a R e in i a a p S E p a a pa i i J R a a RE a a a a a a a p a S R mi p a e ya a a R a S R A a a E e pie a a ER i p a a N ik a S a S a a j y a pa N E a a e S N S p o a B i a N a pa S a E p a e a a pa a a a a a R S S T a a i S a N G s i R i y a a a a a i t el FRONT CENTER LINE ANI J3LN39
3. tach the template to the with a 1 1 4 router spade bit countertop with masking tape and draw twist drill or hole saw Faucets a pencil line around the inside of the may be installed at this time template IMPORTANT USE ROUTER SPADE BIT TWIST DRILL OR HOLE SAW ONLY CAUTION DO NOT USE AN AUGER BIT 4 For final fit apply a bead of caulk 5 Connect all faucet supply lines and not included to the underside of the drain fittings per manufacturer s instruc sink flange and position onto the coun tions tertop opening First tighten screws in front and then tighten rear screws RECOMMENDED CLEANING PROCEDURE FOR SWANSTONE SOLID SURFACE Hard to Remove Stains 1 Abrasive cleaners such as Ajax Comet Bon Ami or Bar Keeper s Friend 2 The use of an abrasive pad such as Scotch Brite 3 For the most stubborn stains fill the Swanstone vanity bowl about one quarter full with a 50 50 solution of bleach and water After ten or fifteen minutes of soaking drain solution from the bowl as you wash and rinse both sides and bottom NOTE DO NOT USE STEEL WOOL OR METAL SCOURING PADS Mineral Based Stains Cleaners designed to remove iron or rust should not harm Swanstone Marks or Discoloration WHITE automotive rubbing compound may be used to remove stubborn marks or discoloration Scratches Use sandpaper starting with 150 grit followed by 220 grit and then 320 grit Finally blend area in using a Scotch Brite pad until scratc
Download Pdf Manuals
Related Search