Mont Blanc 20400NSC Installation Guide
Contents
1. under counter installation kits ADDITIONAL ACCESSORY HOLES Please contact the MONT BLANC Sales Support Center for questions and or instructions on adding accessory holes to your new MONT BLANC sink NN Z YS Be Inspired2. MONT BLANC Installation Guidelines Important Before you Begin Read all instructions carefully before beginning installation Remove the sink from its original carton and inspect it for damage Return the sink to its protective carton until you are ready to place it into position in the countertop Inspect your faucet hardware to insure that all components exist for a successful installation as outlined in the faucet and or hardware installation guide Inspect the waste and supply lines and replace if necessary RECOMMENDED TOOLS amp MATERIALS PUTTY SILICONE i ZO Safety Glasses 100 Silicone Sealant Pencil Plumbers Putty me _ f oe SS SS Regular amp Phillips Masking Tape Paper Towels Channel Locks Screwdriver SELF RIMMING INSTALLATION If this is a replacement for a sink of the same size no cutting of your existing countertop is necessary If this is a new installation or you are replacing a smaller sink we offer the following information No mounting clips are required STEP ONE Position the sink UPSIDE DOWN in the desired location on the countertop Verify the position and desired fit while observing the front overhang that exists on all countertops STEP TWO With a pencil trace a line or apply a border of masking tape around the outside edge of the sink on the counter top STEP THREE Remove the sink from the countertop STEP FOUR Measure in 3 4 and draw new lines inside the first sink outline ju
3. st drawn or taped STEP FIVE Drill a pilot hole inside the line drawn in Step 4 to allow a starting point for the Jig saw STEP SIX Following the line drawn in Step 4 carefully cut out the countertop STEP SEVEN Temporarily position the sink in the countertop opening so the sink edges line up with the pencil line or tape border to insure a successful fit STEP EIGHT Carefully remove the sink and clean the countertop and remove tape if any Pn A owe KONE Be Inspired Continued on Back gt gt gt MONT BLANC Installation Guidelines Important Before you Begin Read all instructions carefully before beginning installation Remove the sink from its original carton and inspect it for damage Return the sink to its protective carton until you are ready to place it into position in the countertop Inspect your faucet hardware to insure that all components exist for a successful installation as outlined in the faucet and or hardware installation guide Inspect the waste and supply lines and replace if necessary SELF RIMMING INSTALLATION con t STEP NINE Mount the faucet hardware on the sink following the manufacturer s instructions STEP TEN Install the drain in accordance with the manufacturers instructions using Plumbers Putty following the manufacturer s instructions Note Silicone Sealant or any other sealants other than Plumbers Putty should not be used as a replacement for Plumbers Putty Apply a thin contin
4. uous bead of 100 silicone sealant to the underside outer perimeter of sink approximately 1 4 inside the perimeter and carefully position the sink in the opening Remember that the sink rests on a layer of silicone sealant not dry fitted to the countertop STEP ELEVEN Verify that the sink has not moved out of position and immediately remove any excess sealant filling any remaining voids as needed ET STEP TWELVE Allow the sealant to cure at least 1 hour before proceeding STEP THIRTEEN Install the garbage waste disposer if applicable following manufacturer s instructions GASKET STEP FOURTEEN Connect the drain assembly STEP FIFTEEN Connect the faucet supply lines following the faucet manufacturer s instructions STEP SIXTEEN Carefully turn on the water supply lines then turn faucet on and check faucet drain and drain assembly for leaks to insure a completed successful installation of your new MONT BLANC Sink UNDER COUNTER INSTALLATION When planning to use a MONT BLANC sink in an under counter installation please check style and size before authorizing cutting of the countertop For under mounting to granite or marble or solid surface materials contact your granite marble solid surface fabricator for installation requirements and proper fasteners Under counter installation kits are available but not required or necessary by all professional fabricators Please contact MONT BLANC Sales Support for details regarding
Download Pdf Manuals
Related Search