American Standard T555.500.002 Installation Guide
Contents
1. GUARD A oe and turn off water supply Find correct position of HANDLE 3 and push HANDLE 3 onto VALVE STEM 4 Push CAP 1 VALVE CARTRIDGE 2 i 1 oven 2 Install HANDLE SCREW 5 and push in INDEX Mount ESCUTCHEON 3 to valve body with SCREWS 4 CAP 6 Remove PIPE CAPS 5 from shower pipe and tub filler pipe Check proper operation of HANDLE Install SHOWER ARM 6 SHOWER HEAD 7 and TUB Turn water supply on and test installed fitting FILLER SPOUT 8 by threading onto pipe nipples using teflon Operate valve and diverter spout tape or pipe sealant A m By restricting HANDLE rotation and limiting the amount of hot water allowed to mix with the cold the HOT LIMIT SAFETY STOP 1 reduces risk of accidental scalding To set the maximum hot water temperature of your faucet you need to adjust the setting on the HOT LIMIT SAFETY STOP 1 Turn CARTRIDGE STEM 2 to the OFF position LE Smaller Numbers coldest setting before making adjustment to SIRS 0135719111315 HOT LIMIT STOP 1 Use a flat blade Z screwdriver to pry free the HOT LIMIT SAFETY STOP 1 Pull forward and rotate counterclockwise one number to limit hot water temperature COLDER Use ARROW 3 on CARTRIDGE 4 and Larger Numbers NUMBERS 5 on HOT LIMIT STOP 1 for 0139571911 18 15 indication M968235 Rev 1 1 4 TO GAIN ACCESS TO VALVE FOR SERVICING Pull INDEX CAP unscrew HAND2. Installation TOWNSQUARE Instructions BATH SHOWER TRIM KIT T555 500 with EverClean Finish T555 501 Congratulations on purchasing your American Standard T555 502 faucet with EverClean finish found only on American Standard faucets EverClean Finish One wipe effortlessly removes spots Eliminates the need for cleaners and scrubbing Permanent surface protectant remains beautiful Certified to comply with ANSI A112 18 1 for the life of the faucet EverClean available on Polished Chrome Satin Nickel M968235 Rev 1 1 Stainless Steel Polished Brass or any combination of these finishes To ensure that your installation proceeds smoothly please read these instructions carefully before you begin D gt O A Phillips Screwdriver Flat Blade Screwdriver Adjustable Wrench Channel Locks Required Tools Plumbers Putty or Caulking ROUGHING IN DIMENSIONS m To assure proper positioning in relation to sl 1 5 8 TO 3 1 4 Hand FINISHED WALL gt wall note roughing in dimensions 1 2 PS OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 65 AND 78 74 FOR HEAD CLEARANCE 32 to 42 BATH SHOWER OPTIONAL BOTTOM OF TUB INSTALL TRIM INSTALL HANDLE CAUTION Protect finish on SHOWER ARM SHOWER HEAD and TUB SPOUT when installing Install HANDLE BUSHING 1 onto CAP 2 When finished tiling the wall remove PLASTER
3. LE SCREW and pull HANDLE off valve stem Remove two SCREWS holding ESCUTCHEON and remove ESCUTCHEON Remove COVER by pulling straight out Shut off water supply by either closing off main water supply or closing off the hot and cold CHECK STOPS on valve VALVE LEAKS WHEN SHUT OFF Remove CARTRIDGE 1 by removing CARTRIDGE SCREWS 2 Remove three SCREWS 3 from FIXATION RING 4 and pull out PRESSURE BALANCING 5 unit Clean SEALS 9 on base of CARTRIDGE 1 Check base of PRESSURE BALANCING UNIT 5 and clean O RINGS 6 Remove CAPS 7 and check O RINGS on inside of CAPS 7 for debris Clean inside sealing surfaces of VALVE BODY 8 Re assemble PRESSURE BALANCING UNIT 5 and CARTRIDGE 1 Tighten all screws Turn on water supply and see above for installing TRIM and HANDLE If it still leaks replace pressure balancing unit M952100 0070A UNABLE TO MAINTAIN CONSTANT TEMPERATURE Remove PRESSURE BALANCE UNIT 5 Remove CAPS 7 and clean valve thoroughly Examine balancing unit and check condition of O ring on end of piston Piston should move back and forth Order Repair Part M952100 0070DA if balancing unit is defective Replace CAPS 7 and install PRESSURE BALANCE UNIT 5 Make sure inlets line up with two holes in bottom of casting Top flange should butt up against top of casting BACK TO BACK INSTALLATION Remove PRESSURE BALANCE UNIT 5 Rotate PRESSURE BALANCE UNIT 5 180 so that the inlets face up and the la
4. rge outlet port faces down Push PRESSURE BALANCE UNIT 5 in casting make sure inlets line up with holes in bottom of casting Top flange should butt up against top of casting Reassemble FIXATION RING 4 and CARTRIDGE 1 LARGE OUTLET ROTATE 180 L va A N WLS as Capp Cg BACK TO BACK INSTALLATION EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface M968235 Rev 1 1
Download Pdf Manuals
Related Search