Home

LIFAN LF2WP-65 Instructions / Assembly

image

Contents

1. Operating Instructions and Owner s Manual LF2WP LF2WP CA LF3WP LF3WP CA LF4WP LFAWP CA PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATING YOUR NEW LIFAN Power USA Water Pump CA Indicates this unit is CARB Certified for California PLEASE READ THE FOLLOWING INSTRUCTIONS 1 Unit Shipped with NO OIL in Engine or where applicable pumps and or accessories Check and fill with proper oil as outlined in the Owner s Manual for the respective product 2 For repair under Warranty or questions concerning Warranty DO NOT return this product to the Store where purchased Follow the procedures as outlined in the WARRANTY POLICY and WARRANTY REGISTRATION in the Owner s Manual For any questions visit www lifanpowerusa com or call 1 866 471 7464 3 Read the Owner s Manual prior to operating any equipment and familiarize yourself with the proper and safe operation of the equipment If you have any questions visit www lifanpowerusa com or call 1 866 471 7464 This Owner s Manual is for the Following Models LF2WP LF3WP LF2WP CA LF3WP CA LF indicates this unit is a LIFAN product WP indicates this unit is a Water Pump CA indicates this unit is CARB Certified for California 2 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com TABLE OF CONTENTS Preface Product Specifications Safety Instructions Controls and Features PRE OPE
2. LF3WP Models Before starting cold water pump rotate the choke lever to the left until resistance is felt After starting the water pump rotate the choke lever to the right to disengage Fuel Cock Turn to OFF position to terminate fuel delivery to engine Recoil Starting Handle Pull Handle to rotate engine for starting Frame linch round steel tubing for maximum protection Engine Switch Rocker Style Set to ON position to start engine amp OFF position to shut engine off Dipstick Check Fill Engine Oil Intake Pipe Pump Suction intake Outlet Pump Pump Discharge pipe Muffler Allows quiet operation Spark Plug Engine Spark Plug location Check Maintenance Schedule for Service Intervals Disengage during transportation and storage NEVER start engine with Spark Plug disengaged 12 Air Cleaner Check Maintenance Schedule for Service Intervals 13 Fuel Filler Cap Vented Fuel Cap must be properly installed at all times during operation ed Re e e OO CO NI 9 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Pre Operating Instructions Connecting Water Inlet Hose Use commercially available hose hose joint and clamp The water inlet hose must be of continuous structure and be non folded The length of the hose should be no more than required The effect of suction is greatest at shorter distances from the water surface Suction time
3. installed in the engine the power output of the engine will drop about 3 5 with every 1000ft 305m increase in altitude If the standard carburetor jets are not replaced and adjusted for usage in high altitude the increased altitude effect will be even more severe NOTE Usage of the water pump in regions with lower altitude than the high altitude carburetor spray nozzle is applicable may result in decrease of engine performance The engine may become overheated and over lean combination of fuel and air produced may cause severe damage to the engine 24 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Troubleshooting IF THE ENGINE WILL NOT START 1 Check to ensure switches are in the ON position 2 Check engine oil level The unit possesses a Low Oil Shutdown feature that will not allow your engine to start if the oil is below safe operating levels This feature is installed to increase the life of your engine and prevent engine damage If oil level is low fill to the full mark on dipstick Refer to the Pre Operating Instructions Engine Oil Check section for exact oil type and amounts 3 Check the fuel level to insure adequate fuel Add fuel if necessary 4 Remove and inspect the spark plug for cleanliness and proper electrode gap If needed clean or replace the spark plug Refer to Spark Plug Maintenance in the Maintenance section of the Owner s Manual for proper proce
4. 866 471 7464 www lifanpowerusa com Water Pump Safety Never operate a gasoline engine powered product in any enclosed spaces as they product deadly Carbon Monoxide Poisonous Gases Do NOT operate your power equipment in inclement weather such as rain snow and or sleet Do NOT operate your power equipment within five 5 feet of any flammable materials When refueling your power equipment never smoke or refuel near any flame or ignition devices Never refuel while the unit is running If during the refueling process some fuel is spilled always completely clean the fuel and allow sufficient drying time prior to re starting your unit Gasoline vapors ignite easily and are very dangerous NEVER ALLOW CHILDREN OR ANIMALS TO BE NEAR THIS EQUIPMENT DURING OPERATION ONLY QUALIFIED PERSONS SHOULD OPERATE THIS EQUIPMENT PLEASE FOLLOW ALL GUIDELINES CONTAINED IN THIS OWNER S MANUAL FOR THE SAFE OPERATION OF THIS EQUIPMENT 26 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com This warranty is limited to the following UFAN Power and Storm Series products that are distributed by the Equipsource LLC dba LIFAN Power USA located at 2205 Industrial Park Road Van Buren AR 72956 Effective 04 25 2010 LENGTH OF WARRANTY po Residential Use Commercial Rental __ Warranty NOT to exceed Products Covered Year 1 Year 2 Year 3 300 hours or terms listed below Walk Behind Mowers Full Uni
5. 9 in Air Cleaner A below or the wing nut item 7 in Air Cleaner B below to remove and check the air filter element 2 For Sponge Type Air Filters wash with soap and water when contaminated Squeeze excess liquid from air filter element and allow the air filter element to dry For Paper Type Air Filters replace with the correct Air Filter for your unit They are available at your dealer or from LIFAN Power USA Order your filter by calling toll free 866 471 7464 3 Re Install the air filter element into the air filter housing Wing Nut Air Cleaner Cover Air Cleaner A Air Cleaner B 14 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Pre Operating Instructions Pump Water Capacity Check A CAUTION e Do NOT run engine without water inside the pump Operation of engine without water inside the pump will cause the pump to overheat Prolonged operation of engine without water inside the pump will damage the pump gasket and impeller e If water within the pump is not full shut off the engine at once and fill the pump after allowing the unit to cool To Check Pump Water 1 Remove Water Filler Cap 2 Visually Check for Water inside pump 3 Iftoo low add water through Water Filler Hole 4 Securely re fasten Water Filler Cap Water filler cap 15 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www li
6. FAWP CA Thank you for purchasing our Pro Series Water Pump All information in this publication is based on the latest product information available at the time of approval for printing We reserve the right to make changes at any time without notice and without incurring any obligation The copyright of this manual belongs to EquipSource LLC No parts of this publication may be reproduced without the written consent of EquipSource LLC This manual should be considered a permanent part of the generator and should remain with it if is resold For Product Support and Service Please Visit Us at www lifanpowerusa com or Call Toll Free 1 866 471 7464 28 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com
7. Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Safety Instructions This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death For your safety read this manual carefully Become familiar with the proper operation care and maintenance of your LIFAN Power USA water pump The safety and alert symbol A is used with a signal word CAUTION DANGER WARNING a pictorial and or safety message to alert you to hazards CAUTION indicates a hazard that if not avoided could result in minor or moderate injury DANGER indicates a hazard that if not avoided could result in death or serious injury WARNING indicates a hazard that if not avoided could result in death or serious injury M Explosion Electrical Shock Hazard Symbols and Meanings Toxic Fumes Hot surface or gas Kickback aM A WARNING Running water pump emits carbon monoxide an odorless colorless poison gas Breathing carbon monozide can cause nausea or death ONLY operate water pump outdoors Exhaust gas must be prevented from entering confined areas Direct exhaust gas away from windows doors ventilation and other openings Do not operate water pump inside or under any buildings A WARNING The engine exhaust from this water pump contains chemicals known to the state of California to cause birth defects re
8. RATING INSTRUCTIONS Connecting Water Inlet Hose Connecting Water Outlet Hose Engine Oil Level Check Engine Fuel Level Check Air Cleaner Element Check Pump Water Capacity Check Operation of Water Pump Transporting and Storing the Unit Maintenance Troubleshooting Water Pump Safety Limited Warranty Policy 3 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com 10 10 11 12 13 14 15 16 19 21 25 26 27 Preface Thank you for choosing LIFAN Power USA for your Power Equipment Needs LIFAN Power USA prides itself on providing quality products at affordable pricing creating the 1 l Best Equipment Value on Today s Market All LIFAN Power USA products are manufactured utilizing the latest technology Built with quality components your new Power Equipment Product will give you years of dependable service Your unit along with all of LIFAN Power USA products are designed engineered and manufactured with LIFAN s Industrial Grade Gasoline Engine This Owner s Manual will provide you with all of your needed information for your new Power Equipment Product including Safe Operation and Maintenance of your unit Please read this Owner s Manual completely and carefully prior to operation Keep this Owner s Manual for assistance in the future such as proper maintenance schedules and tips to prolong the life and effective use of your unit If you r
9. S WAIA ILY VSI TIUU LOLALOU AVNUVE LYUIOUVUUI LO LLY WIN oCVall Ul IOVNIALYE AL ILO YWVNLIVI Aly VAIL LITAL IOVIVYUVOEII LU VO UGICULIVSE IIIT TIIatol IAI or workmanship under normal usage Repairs and or replacement will be made without charge for parts or labor All parts found to be defective must be returned to EquipSource LLC Upon reception of the parts a judgement as to the validity of the warranty caim wil be determined All parts replaced under warranty will be considered part of the original product and any warranty on those parts will coincide with the original warranty 1O OLAINN VVallanily Celvice YOU MUS take tne Pl OOUCL al YOU expense LO dil aul nor zea UFAIN FOWeR FITOQUCLS OF AOL S2125 FOWe FTOQUCLS service center If you are unable to locate warranty service or are disssatisfied with the warranty service that you recieve contact EquipSource LLC at 866 471 7464 At EquipSource s discretion EquipSource LLC may elect to replace a defective unit In this case the end user is responsible for all shipping and handling chargers associated with the exchange This warranty is not valid for products or parts affected or damaged by accident collision normal wear fuel contamination abuse neglect misuse alteration Unsuitable use and or unauthorized parts replacement Mower decks and blades are specifically not warranted for impact or abrasive damage Warranty becomes void if the customer fails to install maintain and or o
10. apors WHEN STARTING EQUIPMENT e Ensure spark plug muffler air cleaner and fuel cap are in place e Do NOT crank engine with spark plug removed e If fuels spills wait until it evaporates before starting engine WHEN OPERATING EQUIPMENT e Do not choke carburetor to stop engine e Do not tip engine or equipment at an angle which causes fuel to spill 7 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Safety Instructions continued While engine is running temperature may exceed 150 F 65 C KATA Server burns may occur O o Exhaust heat gasses can ignite combustibles structures or damage fuel tank causing a fire Do NOT touch hot surfaces and do avoid exhaust gasses Allow water pump to cool before touching Keep at least 6 ft 183cm clearance on all sides of water pump including overhead clear Reflective exhaust heat may damage fuel tank causing fire Code of Federal Regulation CFR Title 36 Parks Forests and Public Property require equipment powered by an internal combustion engine to have a spark arrester maintained in working order complying to USDA Forest service standard 5100 1c or later revision In the state of California a spark arrester is required under section 4442 of the California Public resources code Unintentional sparking can result in fire or electrical shock WHEN TESTING FOR ENGINE SPARK e Do NOT check for spark with the spark plug re
11. d definitions 1 Ensure the storage site for the unitis clean and dry 2 Clean the inside of the water pump a Ifthe water pump was used to pump water with mud sand or other heavy debris i Operate water pump to suck in fresh clean water to wash inside of unit Failure to do so may result in damage to impeller ii After washing remove water drain plug and empty the water in the water pump completely iii Reinstall the water drain plug Before long term storage of your power equipment product typically 30 days or more perform the following 3 Set the fuel cock valve to the OFF position 4 Let the unit continue to run until it stops itself burning all of the fuel in the fuel system 5 Turn the ignition switch to the OFF position 6 Drain the engine oil in accordance with the Oil Change Procedures in this Owner s Manual s Maintenance section Do NOT re fill with oil until ready to use again 7 Remove the Spark Plug in accordance with the Spark Plug Maintenance in the Owner s Manual s Maintenance section Spray a lubricant such as WD40 into the Spark Plug hole to lubricate the top of the piston and walls of the cylinder Replace the Spark Plug 8 Pull starter rope until resistance is felt This will place the valves in the closed position 19 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Transporting and Storing the Unit contin
12. dure 5 If the unit will still NOT start after performing the above checks call our customer hotline at LIFAN Power USA Toll Free 1 866 471 7464 or take the unit to an authorized Service Center NOTE Periodically on the initial start up or after the unit has been stored for a long period of time the float for your Low Oil Shutdown system will stick to the bottom of the oil pan Locate the two 2 wires to the Low Oil Sensor Diode figure Low Oil Sensor Diode to the right located on the side of the engine block Unplug these wires and only after ensuring the engine is full of oil start the engine and allow to run until warm normally 20 minutes as this will heat the oil and release the float on the Low Oil Shutdown System Then re plug the wires to the terminals on the Low Oil Shutdown Sending Unit IF THE WATER PUMP WILL NOT PUMP Check if there is ample water in the pump chamber to fully prime the pump Check if the filter is clogged on the suction hose Check if the hose clamp is securely tightened Check if the water hose is damaged Check is suction height required for the application is too high Refer to Product Specifications section for unit maximum suction height 6 If the water pump still will not pump water call our customer hotline at LIFAN Power USA Toll Free 1 866 471 7464 or take the unit to an authorized Service Center ee S a 25 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956
13. equire assistance please visit our website www lifanpowerusa com or call toll free 866 471 7464 This Owner s Manual contains information with respect to the newest products at the time of publication Due to revision and modifications the information noted in the Owner s Manual might vary from the actual status This Owner s Manual is subject to change without notice The copyright of the Owner s Manual belongs to EquipSource LLC Any group or individual is forbidden to reprint or copy any of this Owner s Manual without the written consent of EquipSource LLC FOR ALL WARRANTY AND SERVICE RELATED ISSUES QUESTIONS DO NOT RETURN YOUR UNIT TO THE STORE OR DEALER WHERE THE ITEM WAS PURCHASED FOR SERVICE VISIT LIFAN POWER USA S WEBSITE WWW LIFANPOWERUSA COM OR CALL 1 866 471 7464 WE WILL BE HAPPY TO HANDLE YOUR WARRANTY ISSUE OR DIRECT YOU TO THE NEAREST AUTHORIZED SERVICE CENTER 4 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Product Specifications Pro Series Water Pumps Model LF2WP CA LF3WP CA LFAWP CA ENGINE 4 Stroke OHV Single 4 Stroke OHV Single 4 Stroke OHV Single Cylinder Cylinder Cylinder Maximum Horsepower MHP 6 5MHP 6 5MHP 9MHP O omom 202802 0 61 z069 20 Dimensions OO owm seo sem zonom OO m onem mso O zaneo Comments MHP Maximum Horsepower L hrs Liters per hour 5 LIFAN Power USA 2205
14. ess liquid from air filter element and allow the air filter element to dry For Paper Type Air Filters replace with the correct Air Filter for your unit They are available at your dealer or from LIFAN Power USA Order your filter by calling toll free 866 471 7464 3 Re Install the air filter element into the air filter housing Air Cleaner A Air Cleaner B 22 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Maintenance continued SPARK PLUG MAINTENANCE Remove Spark Plug Cap refer to Spark Plug Cap Removal figure below Remove Spark Plug with socket and handle supplied with your unit refer to Spark Plug Removal figure below Clean any carbon build up around the Spark Plug Check the Spark Plug Gap and adjust if necessary 0 30 inch gap Lubricate the threads of the spark plug with anti seize compound or engine oil Re install the Spark Plug and Spark Plug Cap Spark Plug Cap Removal Spark Plug Removal FUEL SYSTEM MAINTENANCE NOTE Periodically you can get sediment or trash in your Carburetor Bowl Use the following procedures to clean iv 2 3 4 5 NOTE Turn the fuel cock valve to the OFF Position Remove the carburetor bowl by removing the mounting bolt located at the bottom of the bowl Dump out the old fuel and sediment into an approved container Clean carburetor bowl thoroughly Fit a new rubber washer in
15. fanpowerusa com Operation of Water Pump Water Pump Use Location A WARNING Running water pump gives off carbon monoxide gas It is odorless colorless and highly toxic Breathing carbon monoxide gas can leads to fainting nausea or may result in death e Only operate water pump outdoors e Prevent exhaust gas from entering through windows doors or ventilation intakes any confined areas e DO NOT operate water pump inside any enclosed or roofed areas Before Operating Water Pump Refer to Pre Operating Instruction section for additional procedures and definitions 1 Check water pump condition a Inspect for signs of damage oil or fuel leaks b Remove excessive dirt and or debris from the unit 2 Check Suction and Discharge Hoses a Inspect general condition of hoses to ensure hoses are in serviceable condition i Suction Hose must be reinforced construction to prevent hose collapse b Ensure sealing washer in suction hose connecter is in operable condition c Ensure hose connectors and clamps are securely installed d Ensure filter is in operable condition and securely installed on suction hose 3 Check the Engine a Ensure proper engine oil amount b Ensure air cleaner element is clean and installed c Ensure proper fuel level amount Ensure water pump is on a level surface Ensure engine switch is in the OFF position 6 Ensure water pump is at least 3ft 1m away from building walls and other equipment dur
16. ing operation Do NOT place flammable objects close to water pump ae 16 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com 1 Operation of Water Pump continued Starting the Engine Refer to the Controls and Features section for additional diagrams and definitions 1 Zi 2 Prime the pump Move the fuel cock to the ON position To start a cold engine refer to instruction in the Controls and Features section 2 Choke lever To restart a warm engine leave the choke level in the OPEN position Move the throttle valve lever away from the LOWER position about 1 3 of the way toward the UPPER position Turn the engine switch to the ON position Pull the recoil starting handle lightly until resistance is felt then pull briskly Do NOT allow the starter handle to snap back against the engine Return it gently to prevent damage to the starter Choke level ON a a aaa Fuel cock Setting the Engine Speed 1 2 After starting the engine move the throttle valve lever to the UPPER position for self priming then check the pump output To adjust the pump output which is controlled by the engine speed move the throttle valve lever as needed to attain desired pump output Moving the throttle valve in the UPPER direction will increase the pump output and moving the throttle vale in the LOWER direction will decrease pum
17. moved e Use approved spark plug tester WHEN REPAIRING OR ADJUSTING WATER PUMP e Disconnect the spark plug wire from the spark plug and place the wire where it cannot contact spark plug CAUTION Improper use and care of this water pump will cause damage and shorten its lifespan Failure to follow these actions will void all warranties Use water pump only for appropriate and designated purposes The dealer or customer helpline 1 866 471 7464 can instruct you on intended uses Water pump must be placed on a level surface Do NOT expose water pump to extreme conditions Excessive dust moisture and corrosive vapors will damage unit Cooling slots must be kept clear of debris Shut off water pump and take to a qualified service center if the water pump fails to operate properly NOTE Pumping of inflammable or corrosive liquids such as gasoline seawater chemical solutions alkaline liquids or acids is forbidden with this unit 8 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Controls and Features Qulet pipe Throttle valve lever l Intake pipe Dipstick Frame Engine switch Legend 1 Throttle Valve Lever Controls Engine Speed 2 Choke Lever LF4WP Model Before starting cold water pump pull the choke pin outward from water pump to activate the choke lever After allowing water pump to run for a few seconds push pin inward toward water pump LF2WP amp
18. ngine oil Do NOT use filthy engine oil or vegetable oil e Check engine oil level only with engine stalled and with unit on level ground o Use 4 Stroke Gasoline Engine Oil equivalent in quality with SF SG from API Oil velocity varies with average environmental temperature Select engine oil with proper velocity using the chart below in accordance with you regional environmental temperature SAE Temperature 20 EE EEE ES EE EEE EEE SSS 30 20 10 0 10 20 30 40C Environment temperature Engine Oil Alarm System The engine oil alarm system aides in avoiding engine damage due improper amounts of engine oil in the crankcase Before the engine oil level in the crankcase drops below the safety line the engine oil alarm system will automatically stall the engine while the engine switch remains in the ON position om Oe Upper lever mark Nether lever mark LA If the engine stops and will not restart 1 Remove the engine oil dipstick and wipe it clean 2 Insert the dipstick into engine oil filler hole without screwing it in 3 Remove dipstick and check engine oil zi A amount Wa 4 If engine oil is below required amount fill specified engine oil up to the top of filler hole Use engine oil depended on environmental temperature Refer to Product Specification section for proper engine oil capacity 12 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 ww
19. p output So Throttle level 17 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Operation of Water Pump continued Stopping the engine Refer to the Controls and Features section for additional diagrams and definitions IN EMERGENCY 1 Turn the engine switch to the OFF position NORMAL PROCEDURE 1 Move the throttle valve lever to the LOWER position 2 Turn the engine switch to the OFF position 3 Turn the fuel cock to the OFF position 4 Remove the water drain plug and drain the pump chamber 5 Remove the water filler cap and flush the pump chamber with fresh clean water 6 Allow water to completely drain from the pump chamber 7 Reinstall the water drain plug 8 Reinstall the water filler cap 18 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Transporting and Storing the Unit A CAUTION To avoid fire allow water pump to cool down for at least twenty 20 minutes before transporting or storing the unit e Always transport and store the unit with the fuel cock in the OFF position e Always keep unit in horizontal position to the ground to prevent fuel from spilling Spilled gasoline and gasoline vapor may ignite e Gasoline is extremely flammable and explosive Storing the Water Pump Refer to the Controls and Features section for additional diagrams an
20. perate this product is accorance with the instructions and recommended actions of UFAN set for in the owner s manual Equipsource LLC disdaims any responsibility for time loss or loss of usage of the product transportation commercial loss or any other incidental or consequenial damage Prior to any warranty service an approval code must be issued to the service center in order for the warranty daim to be valid Any implied warranties are limited to the duration of this written limited warranty This warranty gives you specific legal rights and you may also have other rights which may vary from state to state Exdusions to Warranty Failure to perform Periodic Maintenance as required and specified in the supplied Owner s Manual Improper repair of product or replacement of parts with non OEM Original Equipment Manufacturer parts Operation in uses and methods other than those outlined in the Owner s M anual Service and or repairs performed by anyone other than an Authorized LIFAN or Storm Series Products Service Center More Information Available on our website www lifanoowerusa com EquipSource LLC 2010 Revised 04 25 2010 27 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Please Read this Owner s Manual Carefully Before Operating Your New Water Pump This Owner s Manual includes the operation and maintenance of the LF2WP LF2WP CA LF3WP LF3WP CA LF4WP amp L
21. productive harm and cancer 6 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Safety Instructions continued A WARNING Rapid recoil of starter cord kickback may pull hand and arm forward toward engine at a rapid rate Broken bones bruises sprains and fractures may result e When starting engine pull cord slowly until tension is felt then pull rapidly to avoid kickback A WARNING W Fuel and its vapors are extremely flammable and explosive Li Fire or explosion can cause severe burns or death WHEN ADDING OR DRAINING FUEL e Turn water pump off and let it cool for at least three minutes before removing fuel cap Loosen cap slowly in order to relieve pressure in the fuel tank Fill or drain fuel tank outdoors Do not excessively inhale fuel vapors Keep away from open flames or sparks and other sources of ignition Do NOT smoke while filling fuel tank Do NOT overfill tank Allow space for fuel expansion WHEN TRANSPORTING OR REPAIRING EQUIPMENT e Transport water pump with the fuel valve in the off position e Repair water pump with the fuel tank empty or the fuel valve in the off position e Disconnect spark plug wire before transport or service WHEN STORING FUEL OR EQUIPMENT CONTAINING FUEL e Store away from furnaces stoves water heaters clothes dryers or other appliances that have pilot light or other ignition source because they can ignite fuel v
22. t Parts amp Labor Full Unit Parts Only Engine Parts Only Full Unit 3 Months Parts amp Labor Full Unit Parts amp Labor Full Unit Parts Only Engine Parts Only Full Unit 12 Months Parts amp Labor Full Unit 12 Months Parts amp Labor Full Unit Parts amp Labor Gasoline Powered Welders Full Unit Parts amp Labor Full Unit Parts Only Engine Parts Only Full Unit 6 Months Parts amp Labor Pressure Washer Pumps All UFAN Pressure Pro and Storm Series Pressure Storm pressure washers are equipped with Annovi Reverbi Gaia pressure water pumps which are warranted by the manufacturer s One 1 Year Limited Warranty Visit www lifanfoowerusa com for details Residental Use Residential Use is definted as items that are for personal use Commerical Rental Commerical or Rental use is defined as any usage for income producing or other business related uses In order to qualify for the limited warranty the product s must be purchased in North America from an authorized EquipSource LLC dealer or a dealer authorized by EquipSource LLCto sell UFAN products This warranty is non transferable and applies only to the original purchaser The supplied Warranty Registration Card must be completed and on file with EquipSource LLC at the supplied address at the time that any warranty daim is made The Warranty Registration Card must be submitted with a receipt of purchase which clearly states the date of purchase WUI IY UI
23. the engine oil into an approved receptacle and discard in accordance with all Federal and State Regulations Never dump your used engine oil on the ground or into drains only discard in an approved manner Check with your local authorities to determine the regulations in your area WARNING AVOID SPLASHING OF HOT OIL IT CAN BURN YOU AND CAUSE SEVERE INJURY 3 After oil is completely drained replace oil drain plug and tighten with appropriate tools Replace oil with the proper oil for your product Refer to the Pre Operating Instructions Engine Oil Level Check section for exact fill requirements Always use your dipstick to check the oil level and only fill to the full mark on the dipstick Never overfill the engine as this can cause damage to the unit and void warranty 21 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Maintenance continued OIL CHANGE PROCEDURES continued 4 Replace the dipstick on your engine PROPER MAINTENANCE OF YOUR UNIT WILL INCREASE THE LIFE OF YOUR PRODUCT THE OIL MUST BE CHANGED ON A REGULAR BASIS FOR PROPER OPERATION AND RELIABILITY AND TO ALSO MAINTAIN YOUR WARRANTY ON THIS PRODUCT AIR CLEANER MAINTENANCE 1 Remove the clip item 9 in Air Cleaner A below or the wing nut item 7 in Air Cleaner B below to remove and check the air filter element 2 For Sponge Type Air Filters wash with soap and water when contaminated Squeeze exc
24. to place and re attach fuel bowl to the carburetor Removal of the drain screw at the bottom of the bowl can drain the fuel to remove smaller debris that has collected in the bowl 6 ya After bowl is securely back in place turn the fuel cock valve to the ON position for use Units equipped with a pre filter for fuel will have a filter housed just below the fuel cock Remove the fuel filter element refer to Fuel Filter Element Removal and clean or replace 23 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Maintenance continued FUEL SYSTEM MAINTENANCE continued diagram below and either clean or replace the fuel filter element Re assemble the fuel filter element refer to Fuel Filter Element Assembly diagram below Fuel Filter Element Removal Fuel Filter Element Assembly USAGE IN HIGH ALTITUDE REGIONS In regions with high altitude the standard carburetor produces overly dense combinations of fuel and air which result in decreased engine performance and increased fuel consumption To maintain high engine performance at high altitudes install a high altitude carburetor main spray nozzle and re adjust the adjusting screw for idle speed For usage in regions with an altitude of over 4 527ft 1380m contact your dealer to replace the standard carburetor and make needed adjustments in advance Even with a proper high altitude carburetor spray nozzle
25. ued 9 Add the recommended amount of fuel stabilizer in accordance with the amount recommended by the manufacturer of the fuel stabilizer to the unused gasoline left in the unit s tank 10 Place the unit in a clean dry and secure location 11 Cover the unit to protect from dust 20 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Maintenance MAINTENANCE SCHEDULE SAA MA Enone Oil After Each 40 Hours of Use For Initial Break p 6 in After First 1 10 Hours of Use Check Each Use Replace As Needed or After Air Cl Fil Every 100 Hours of Use Impeller Check After 300 Hours of Use or After First Year Air Cleaner Wash When Needed Spark Plug When Needed Check amp Re adjust annually or after 300 Hours of Use Fuel Tank Replace Every 3 Years Based on Condition NOTE Refer to Following Procedures for Proper Method to Perform Maintenance Valve Clearance OIL CHANGE PROCEDURES Periodic Maintenance of your engine oil should be performed after each 40 hours of use of you Power Equipment Product Check your engine oil level prior to each use 1 Start your engine and let it warm up to get the oil warm and thinner Remove the dipstick Refer to Controls and Features section by turning counter clockwise Remove the oil drain plug Refer to Controls and Features section located below the dipstick utilizing the appropriate tools CAUTION THE OIL MAY BE HOT 2 Drain
26. varies with the length of the water inlet hose The filter matching with the water pump should be mounted to the end of the water inlet hose with a hose clamp Gasket Inlet hose fA A CAUTION e Before pumping install the filter securely to the end of the water inlet hose This filter will filtrate any impurity which may produce a passage jam and damage impellers e Be sure to install the hose joint and clamp properly to prevent air leaks and pumping performance drop a loose water inlet hose will decrease the water pump performance and self suction ability 10 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Pre Operating Instructions Connecting Water Outlet Hose Use commercially available hose hose joint and clamp A short hose with a big diameter will provide the best performance A long hose with a small diameter will increase flowing resistance and decrease the power output of the water pump Gasket Outlet hose fA NOTE Tighten the hose clamp to keep from disengaging during operation under high pressure 11 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Pre Operating Instructions Engine Oil Level Check A CAUTION Running engine with insufficient engine oil can cause severe damage to the engine e The engine performance and service life is directly dependent of the quality of the e
27. w lifanpowerusa com A CAUTION Pre Operating Instructions Engine Fuel Level Check Gasoline is extremely flammable Keep away from ignition sources Fuel unit only in well ventilated areas with the engine stalled Do NOT smoke near unit Do NOT spill fuel out of the fuel tank Spilled gasoline and gasoline vapor may ignite If gasoline is spilled wipe completely dry before starting the engine Avoid repeated or sustained breathing of gasoline Avoid skin contact with gasoline Keep our of reach of children and pets Do NOT use contaminated gasoline Keep dirt dust and water our of fuel tank After fueling is complete ensure fuel filler cap is securely fastened To Check Engine Fuel Level 1 Zi 3 Remove fuel filler cap Visually check fuel level within gas tank If too low add fuel Only use specified gasoline Unleaded Gasoline is recommended Refer to Product Specification section for fuel tank capacity 13 LIFAN Power USA 2205 Industrial Park Road Van Buren AR 72956 866 471 7464 www lifanpowerusa com Pre Operating Instructions Air Cleaner Element Check A CAUTION e Do NOT run the engine without air cleaner element installed Operation of engine without air cleaner element installed will result in the inhalation of dirt dust and other debris into the engine and through the carburetor This will result in premature wear of the engine To Check Air Cleaner Element 1 Remove the clip item

Download Pdf Manuals

image

Related Search

Related Contents

KDC-M4524 KDC-M4524G  020-101798-03_LIT GUID START Roadie 4K45-FRA.book  FAUQUIER COUNTY WATER AND SANITATION AUTHORITY  

Copyright © All rights reserved.
Failed to retrieve file