American Standard 4101.000P.075 Installation Guide
Contents
1. into ESCUTCHEON 1 From underside of sink or mounting surface thread LOCKNUT 12 onto SPRAY HOLDER 11 shank and tighten Install SPOUT ASSEMBLY Insert SPRAY HOSE 9 and SHANK 10 through ESCUTCHEON 1 and mounting surface Make sure slot in spout base aligns with tab on ESCUTCHEON 1 Figure 2 Assemble RUBBER WASHER 4a BRASS WASHER 5a and threaded LOCKNUT 6a onto SHANK 10 from underside of sink or mounting surface Hand tighten LOCKNUT 6a Use a screwdriver to tighten SCREWS 8a on LOCKNUT 6a the same as fitting installation above Figure 2 ALIGN SLOT AND TAB INSTALL FAUCET WITHOUT ESCUTCHEON PLATE 4101 115 with soap dish 4101 350 less soap dish E Insert SEAL WASHER 1 into ESCUTCHEON 2 Place ESCUTCHEON 2 onto sink or mounting surface Insert supply TUBES 3 and SHANK 4 through ESCUTCHEON 2 and mounting surface Make sure slot in fitting base aligns with tab on ESCUTCHEON 2 Figure 1 Assemble RUBBER WASHER 5 BRASS WASHER 6 and threaded LOCKNUT 7 onto SHANK 4 from underside of sink or mounting surface Hand tighten LOCKNUT 7 and check that rotation of HANDLE 8 from HOT to COLD is centered Use a screwdriver to tighten SCREWS 9 on LOCKNUT 7 Work your way around LOCKNUT 7 tightening the SCREWS 9 slightly each time until all are snug to ensure even pressure Install SPRAY HOLDER Insert SPRAY HOLDER 11 into ESCUTCHEON 12 Ins2. Installation Instructions ARCH 4101 301 Serie HI FLOW KITCHEN FAUCET with SIDE SPRAY Thank you for selecting American Standard 4 101 301 shown with 4101 301 the benchmark of fine quality for over 100 years aptipnal essuterean A101 600k To ensure that your installation proceeds smoothly __ Certified to comply with ANSI A112 18 1M please read these instructions carefully before you begin M968583 Rev 1 2 RECOMMENDED TOOLS Adjustable Wrench Regular Screwdriver Phillips Screwdriver Channel Locks INSTALL FAUCET WITH DECK ESCUTCHEON gal cia caurion Maier Installation with DECK ESCUTCHEON Apply a light bead of plumbers putty to underside of ESCUTCHEON 1 if mounting surface is uneven Place ESCUTCHEON 1 onto sink or mounting surface with large opening to the right as shown Insert supply HOSES 2 and SHANK 3 through ESCUTCHEON 1 and mounting surface Make sure slot in fitting base aligns with tab on ESCUTCHEON 1 Figure 1 Assemble RUBBER WASHER 4 BRASS WASHER 5 and threaded LOCKNUT 6 onto SHANK 3 from underside of sink or mounting surface Hand tighten LOCKNUT 6 and check that rotation of HANDLE 7 from HOT to COLD is centered Use a screwdriver to tighten SCREWS 8 on LOCKNUT 6 Work your way around LOCKNUT 6 tightening the SCREWS 8 slightly each time until all are snug to ensure even pressure Install SPRAY HOLDER Insert SPRAY HOLDER 91
3. RIDGE 6 off MANIFOLD 7 and remove CARTRIDGE SEALS 8 Clean MANIFOLD 7 CARTRIDGE 6 ports and SEALS 8 Place SEALS 8 into CARTRIDGE PORTS 6a Place CARTRIDGE 6 onto MANIFOLD 7 and tighten MOUNTING SCREWS 5 alternately Replace ESCUTCHEON CAP 4 HANDLE 3 tighten HANDLE SCREW 1 and install INDEX BUTTON 2 Test fitting CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE M968583 Rev 1 2
4. ert SEAL 14 into underside of ESCUTCHEON 12 From underside of sink or mounting surface thread LOCKNUT 13 onto SPRAY HOLDER 11 shank and tighten Install SPOUT ASSEMBLY Insert SEAL WASHER 1a into ESCUTCHEON 2a Insert SPOUT HOSE 10 and SHANK 11 through ESCUTCHEON 2a and mounting surface Make sure slot in spout base aligns with tab on ESCUTCHEON 2a Figure 2 Assemble RUBBER WASHER 5a BRASS WASHER 6a and threaded LOCKNUT 7a onto SHANK 11 from underside of sink or mounting surface Hand tighten LOCKNUT 7a Use a screwdriver to tighten SCREWS 9a on LOCKNUT 7a the same as fitting installation above Figure 1 Figure 2 ALIGN SLOT AND TAB ALIGN SLOT AND TAB 2 MAKE WATER SUPPLY CONNECTIONS Push HOSE END 1 with compression fitting onto COPPER TUBE 2 Make sure HOSE and COPPER TUBE are fully engaged approx 1 2 engagement Use adjustable wrench to tighten connections Do not over tighten Turn off hot and cold water supplies before beginning Connect FLEXIBLE SUPPLIES 3 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left supply Marked with a Red Stripe to Hot and right supply to Cold wall supply Use adjustable wrench to tighten connections Do not over tighten Faucet supplies are 24 1 2 long from faucet base Note If additional supply length is required installer must purchase those parts separately Important If SUPPLY HOSES 3 are too long loo
5. p as illustrated to avoid kinking M968583 Rev 1 2 CONNECT SPRAY HOSE AND SPOUT HOSE m Feed HAND SPRAY HOSE 1 through SPRAY HOLDER 2 Use wrench to tighten COUPLING NUT 3 on SPRAY HOSE 1 to SIDE SPRAY CONNECTION 4 on fitting m Make sure SEAL WASHER 5 is installed in COUPLING NUT 6 Connect threaded end of HOSE 7 to SPOUT HOSE COUPLING NUT 6 from fitting Use wrench to tighten 4 CHECK CONNECTIONS FOR LEAKS m Move HANDLE 1 down into off position Turn on water supplies and check connections for leaks CHECK CONNECTIONS FOR LEAKS M968583 Rev 1 2 5 TEST INSTALLED FAUCET Move HANDLE 1 down into off position Remove AERATOR 2 Operate handle up and down in COLD and HOT positions to flush water lines thoroughly m Replace AERATOR 2 m With HANDLE 1 down in off position pull HAND SPRAY 3 from holder and direct SPRAY END 3 into sink Check HAND SPRAY 3 operation gm With faucet on push BUTTON 4 to activate HAND SPRAY 3 Release BUTTON 4 to stop spray and return HAND SPRAY 3 to holder SERVICE If faucet drips operate HANDLE several times from off to on Do not apply excessive force Clogged CARTRIDGE outlets or inlets may cause reduced flow To clean first turn off water supply then m Remove INDEX BUTTON 1 loosen HANDLE SCREW 2 and remove HANDLE 3 Unthread ESCUTCHEON CAP 4 Unthread three MOUNTING SCREWS 5 Lift CART
Download Pdf Manuals
Related Search