none 10729 Instructions / Assembly
Contents
1. Item 1000 055 633 1000 055 634 1000 055 635 1000 055 639 1000 055 643 1000 055 646 F4 GLACIER BAY USE AND CARE GUIDE Pop Up Drain Body and Trim THANK YOU We appreciate the trust and confidence you have placed in Glacier Bay through the purchase of this product description We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Glacier Bay Warranty Glacier Bay products are manufactured with superior quality standards and workmanship and are backed by our limited lifetime warranty Glacier Bay products are warranted to the original consumer purchaser to be free of defects in materials or workmanship We will replace FREE OF CHARGE any product or parts that proves defective Simply return the product part to any of The Home Depot retail locations or call 1 855 HD Glacier 1 855 434 5224 to receive the replacement item Proof of purchase original sales receipt from the original consumer purchaser must be made available for all Glacier Bay warranty claims This warranty excludes incidental inconsequential damages and failures due to misuse abuse or normal wear and tear This warranty excludes all industrial commercial amp business usage whose purchasers are hereby extended a five year limited warranty from the date of purchase with all other terms of this warranty applying except t2. d remove 3 Installing the flange 4 Installing the drain body a Apply silicon caulking to the a From underneath the sink screw underside of the flange B the drain body into the flange B b Place the flange B in the b Ensure the pivot ball cavity F sink hole faces the sink and faucet c Hand tighten the locknut E to the bottom of the sink Then use a basin wrench to quarter turn and tighten again Ensure the tapered side of the gasket C is against the bottom of the sink and the flat plastic washer D is between the tapered gasket C and locknut E d Connect the tailpiece G to the P trap by tightening the nut on the P trap to secure the assembly is in place mi P trap nut P trap Installation continued 5 Installing the lift rod 6 Installing the stopper assembly a While holding down the lever rod H place the stopper A through the flange B and into the sink a Insert the ball portion of the lever rod H into the pivot ball cavity F b Screw the lever rod nut 1 over the b Turn the stopper A clockwise to lever rod H and hand tighten to lock in place with the lever rod H secure the lever rod H in place The lever rod ridge MUST be NOTE Verify the stopper A goes up facing right side from front as the and down with the lever rod If not drawing shows readjust the stopper A and lever rod H position c Make sure the nut
3. he duration of warranty Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state and province to province Please see a store or contact 1 855 HD Glacier for more details 94 GLACIER BAY Questions problems missing parts Before returning to the store call Glacier Bay Customer Service 8 a m 6 p m EST Monday Friday 1 855 HD GACIER HOMEDEPOT COM GLACIERBAY Pre Installation TOOLS REQUIRED Silicon caulk Wrench PACKAGE CONTENTS ret osc Stopper C Tapered gasket i Pe pee Ci teers oo Pivot ball cavity oo Plastic washer Installation Removing the old drain Preparing the faucet assembly assembly for installation a Turn off the water supply to the a Unscrew the lever rod nut I faucet completely from the drain body b Remove the old pivot rod clip b Twist the locknut E plastic and lift rod washer D and tapered gasket C all the way down close to the pivot c Unscrew the P trap from the drain ball cavity F tailpiece c Clean sink hole Place the new pop up body underneath the sink to verify that the tailpiece G portion fits into the P trap d Loosen the locknut that secures the drain body to the sink e Unscrew the drain assembly from the flange an
4. is tight enough to prevent leaks but loose enough so that the lever rod moves up and down easily 7 Installing the lift rod 8 Completing the installation a Insert the lift rod L into the hole in a Turn on the water supply to the the back of the faucet faucet and check for leaks b From underneath the sink slide b Wipe off any excess silicon the rubber locking ring K up from the bottom of the lift rod L and hold it high c Press the longer end of the rubber linkage arm J over the lift rod L and the shorter end over the lever rod H d Slide the locking ring K over the linkage arm J to hold the lift rod L in place Check to verify that the linkage arm J pop up function and the locking ring K holds the lever rod H in place
Download Pdf Manuals
Related Search