American Standard T064.740.295 Installation Guide
Contents
1. E See Step 2 for HANDLE 3 installation Figure 1 ARROWS AT 3 O CLOCK POSITION a J KNOB MOUNT TEMPERATURE LIMIT STOP RED LOCKING DEVICE p M968984 REV 1 22. Atricam Standard Installation Instructions SERIN TOG64 740 2 HANDLE THERMOSTAT WITH VOLUME CONTROL TRIM KIT Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Certified to comply with ANSI A112 18 1M ASSE 1016 M968984 REV 1 2 ROUGHING IN DIMENSIONS FINISHED ALL 200mm 7 7 8 R520 1 2 NPT INLETS or R540 3 4 NPT INLETS NOTE FITTING a MUST BE INSTALLED _ 1 WITH VOLUME CONTROL 2 to 2 5 8 ON TOP Recommended Tools ES Flat Blade Screwdriver Phillips Screwdriver CARE INSTRUCTIONS m Remove as much surface dirt and film using clear l water and soft cotton cloth as described above E To keep your new faucet looking new please follow these simple care instructions m Use any of the following to remove tough surface film and build up DO E Simply rinse the faucet clean with clear water B Mild liquid Se eee E Dry the faucet with a soft cotton cloth E Clear ammonia free liquid glass cleaners O NOT m Non acidic non abrasive gentle liquid or fully DO NOT dissolved powder cleansers mixed according to E Do not use any abrasive cleaners cloths or manufacturers directions paper towels E E Non abrasive liquid polishers E Do not use any cleaning agents containing acids polish abrasives or harsh cleaners or m Once clean r
3. emove check stops and re install them transposed pees BLUE TO RED Important note RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left Turn the water supply back on and perform the temperature adjustment in step 4 Assemble HANDLES and TRIM CHECK STOP RED TO BLUE M968984 REV 1 2 4 TEMPERATURE ADJUSTMENT m Pull out COVER CAP 1 and loosen SET SCREW 2 Pull off HANDLE ASSEMBLY 3 m Check that arrow marking B points to the 3 o clock position If not push the BLACK CLAMP on the SECURING RING to the right pull off KNOB MOUNT 4 and reinstall KNOB MOUNT 4 with arrow B 3 o clock position See Figure 1 SET HOT LIMIT STOP m The maximum mixed water temperature is set at 109 F at the factory This setting can be changed if desired m Remove the TEMPERATURE LIMIT STOP H shaped Black Plastic part Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104 F or 112 F E For 100 F adjustment turn the water supply on Turn KNOB MOUNT 4 until the spout temperature is 100 F Check that arrow A on the KNOB MOUNT 4 still points 3 o clock position after adjusting the thermostat to 100 F If not pull out the RED LOCKING DEVICE Remove KNOB MOUNT 4 by pulling it towards you while standing directly in front of the valve m Reinstall the KNOB MOUNT 4 with arrow A 3 o clock position E Reinstall RED LOCKING DEVICE
4. inse faucet again with clear water to soaps thoroughly remove cleaner or polish and blot dry with a soft cotton cloth m Regular and routine cleaning will reduce the need for heavy cleaning and polishing If heavy cleaning is f required the following procedures are recommended Failure to follow these care instructions may damage the Faucet s finish 1 TRIM INSTALLATION Remove PLASTER GUARD 1 if attached Push CAPS 2 amp 2a as shown onto CONTROL VALVES 3 m Push ESCUTCHEON HOLDER 4 with lightly greased O RING SEALS 5 over CAPS 2 2a Attach with the two SCREWS 6 provided m Align pins in back of ESCUTCHEON 7 with holes in ESCUTCHEON HOLDER 4 and push ESCUTCHEON 7 into place INSTALL HANDLES Align HANDLE 1 as shown and push onto KNOB MOUNT 2 Tighten SET SCREW 38 with flat blade screwdriver Push COVER CAP 4 into SET SCREW 3 Install HANDLE ADAPTER 5 onto VALVE STEM 6 Install HANDLE SCREW 7 and tighten Push VOLUME CONTROL KNOB 8 onto HANDLE ADAPTER 5 Use HEX WRENCH 9 supplied and tighten set screw to secure VOLUME CONTROL KNOB 8 Mm Thread LEVER HANDLE 10 into VOLUME CONTROL KNOB 8 TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION Should the hot and cold water supply pipes have been transposed making adjustment impossible proceed as follows E Shut off water supply E Remove handle and rim Reverse steps 1 and 2 E R
Download Pdf Manuals
Related Search