Little GIANT 509635 Instructions / Assembly
Contents
1. Little GIANT Little Giant P O Box 12010 Oklahoma City OK 73157 2010 405 947 2511 Fax 405 947 8720 www LittleGiant com customerservice lgpc com ASSEMBLY INSTRUCTIONS FOR 9S SMPX LG 10S SMPX LG BOLT ON VENT DISCHARGE FLANGES PRE PACKAGED UNIT FIGURE 1 Verify all parts with basin and cover assemblies are received intact The flang es provided will allow the following discharge vent combinations to be used 3 discharge 2 vent or a 2 discharge 2 vent depending on cover configuration Please note that basin should be backfilled with cover secured on basin to ensure that cover holes will align properly 1 Remove bolts and washers in cover and set aside 2 Remove gasket material from hardware kit and place material around circumference of basin inside of bolt circle 3 Place the pump on a flat surface and install the discharge pipe in the discharge of the pump 4 Install float switch 4 above discharge of pump with a 3 1 2 tether length Float switch should be installed in a manner that will not allow it to contact the pump or side of basin during operation Refer to float switch instruction manual for alternative settings Place the pump in the basin in the torque stops 5 To install the cover pull the pump and float cords through the small est hole in the cover Place the cover on the basin making sure the discharge pipe is through the proper hole in the cover holes are labeled on bottom of cov2. er Secure the lid to the basin using the bolts and washers provided Place the larger square cut O ring on discharge pipe with beveled edge down Install flange and tighten bolts Place the remaining O ring in the bottom of the vent flange with beveled edge down Install flange and tighten bolts 6 Pull the slack out of the cords and install them through the grommet 1 2 inches above the cover Press the grommet in the hole in the cover 7 Install a 2 vent pipe by threading it on the vent flange Make sure the flange bolts are tight PRE ASSEMBLED UNIT FIGURE 2 The pre assembled unit is furnished fully assembled and ready for installation Remove check valve or ball check valve from discharge pipe and re install as shown on typical installation Figure 3 CAUTION For best performance of check valves when handling solids install in a horizontal position or at an angle of not more than 45 Do not install check valve in a vertical position as solids may settle in valve and prevent opening on start up Remove the cord from the vent hole and install the vent pipe see Figure 3 to complete typical installation To test the unit plug the unit in and run water into the basin until the unit switches on If the unit does not operate refer to the troubleshooting information in the instructions for the pump LITTLE GIANT SEWAGE ACCESSORIES amp INSTRUCTIONS FOR TYPICAL INSTALLATION REPLACEMENT PARTS LIST P N DESCRIPTION ASIN 20
3. x 30 OVER ASSEMBLY 2 DISCHARGE OVER ASSEMBLY 3 DISCHARGE COVER ASSEMBLY HARDWARE KIT 1 6 N A _ GROMMET 2 HOLE tt 8 940022 cHECK valve 2 tt 1 8 940023 CHECK VALVE 3 only on 509112 amp 509113 940026 CHECK VALVE BALL VALVE 2 only on 509106 1 509107 amp 14940684 Figure 1 Pre Packaged TORQUE 15 20 IN LBS COVER ASSY COVER ASSY POLYBAG BASIN 2 DISCHARGE PIPE PUMP SHOWN WITH OPTIONAL CHECK VALVE Figure 2 pire Pre Assembled TUCK EXCESS POWER CORD IN VENT HOLE FOR SHIPPING TORQUE 10 15 INLBS CHECK VALVE OR BALLICHECK VALVE Figure 3 Typical Installation GATE VALVE UNION VENT 6 5 8 2 CHECK VALVE 4 OR BALL CHECK 7 VALVE is ZN X Z GASKET TAPE 7 ri PUMP ON LEVEL AIR BLEED PUMP HOLE OFF LEVEL A L796 Copyright 2006 Little Giant Form 998264 03 2006 Little Giant Print Services
Download Pdf Manuals
Related Search