Everbilt PUP63_HD Instructions / Assembly
Contents
1. ccssccsssessssersssresssssssseeesssensseessseeseas 3 Safety Information instructions He Tap AN SANE NSA Me uvelolls WARNING Never use in explosive atmospheres 2 Read carefully before attempting to assemble operate or The pump is not explosion proof maintain this product Protect yourself and others by observing all safety information Failure to comply with WARNING Fire hazard Never pump gasoline or other these instructions can result in personal injury and or volatile or flammable liquids with this unit property damage WARNING Follow all safety precautions recommended 3 Retain these instructions for future reference by the manufacturer of the electric drill LIMITATIONS WARNING Operate with a 3 wire grounded power cord This device was designed for use with clean water and motor only or with a double insulated drill oil only CAUTION Disconnect the electric drill before attempting to service the pump CAUTION Provide a means of pressure relief in case the discharge line is shut off or obstructed CAUTION Always check hoses before using the pump Replace if worn or weak CAUTION Always check all connections for tightness before using the pump Warranty WHAT IS COVERED This pump is guaranteed for 90 days from date of purchase It will pump clean water and motor oil WHAT IS NOT COVERED Pumping anything other than clean water and motor oil and if damajed due to misuse from primarily b2. intended to be operated unattended or continuously Doing either of these can cause the pump and drill to fail Ys DN K Lx MY TOV IX Maintenance Normal use of the pump causes it to wear To extend pump life o Lubricate the impeller with cooking oil or mineral oil o Always flush with clear water after using o Keep the suction line as short as possible and prime the line fill with liquid when possible before starting the pump Troubleshooting Probable Cause Corrective Action The pump will not prime Air is leaking into the inlet hose or Replace the washer in the hose fitting or connection replace the hose The inlet hose is The inlet hose is clogged The inlet hose is clogged Clean or Clean or replace the hose the hose The hose collapsed due to inlet line suction Acer aaa the end of the inlet line where it meets on a flat surface the flat surface The impeller body and end cover are worn Replace the pump from pumping abrasives The impeller blades are missing or charred Replace the pump from dry running Air is leaking in at the seal or O ring Replace the pump The shaft turns but the impeller does not Replace the pump turn There is a low flow rate The drill is running too slowly Increase the drill speed or use another 1 4 in drill or larger There is restriction in the inlet or discharge Clean or replace the hoses Check hoses to hoses eliminate any sharp bends or kinks in the
3. lines Liquid is leaking where the The lip seal is damaged Replace the pump shaft enters the pump body 7 HOMEDEPOT COM Please contact 1 800 305 1726 for further assistance EVERBILI Questions problems missing parts Before returning to the store call Everbilt Customer Service 8 a m 6 p m EST Monday Friday 1 800 305 1726 HOMEDEPOT COM Retain this manual for future use
4. D Item 147 877 EVERBILT Model PUP63_HD USE AND CARE GUIDE DRILL PUMP Questions problems missing parts Before returning to the store call Everbilt Customer Service 8 a m 6 p m EST Monday Friday 1 800 305 1726 HOMEDEPOT COM THANK YOU We appreciate the trust and confidence you have placed in Everbilt through the purchase of this drill pump We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Everbilt Table of Contents Wea DIG of Conte Sarrosa 2 Tools Required osccccdssesecsicasdacedeagsacacoastnneieccnersuceevetbesceitebeestenkies 3 Safety Information s ssessensenseuneuneunnunnunnennennennnnnnnnnnnn nnne 2 Package Contents ssssscessssessssesesessesessessesessesessesesstsessesesees 4 Warranty E E E AA A E 3 ASSEMDIy cessessessesecscscsocsecsecsecsessecsersessessessessessesecsacesee 5 What is Covered ccccssscssssssssssessscsssssessscsessscusssaeesssenensceuens 3 Operation csccccssssssccoesssssecsocsssssecssessssssessessecsscsensssnssesssess 6 What is NOU GOVETEU ispisna aiaeag 3 METAT aTe 7 Pre Assembly snunnsnnennunnennunnunnunnannunnunnunnunnunnunnnnnnnnnnnnnn 3 Troubleshooting i icsisccasiensitunccnsvcascensecsacennvetacwsntvenwesanesanes 7 Product Specifications cccseccsssesssesssreesseeessseesssenensseeseeas 3 Planning Operation
5. e and or not more than 25ft horizontally O O from the water source Attach the drill pump with hoses to the drill Connect the drill motor power cord to a 3 wire grounded plug WARNING To minimize the pump rotating on the drill firmly grip the drill pump and hold it as you start the drill WARNING Ensure water is drawn into the drill pump within 15 20 seconds to avoid damaging the pump If it does not check to ensure the hose connections are firmly installed to the pump C ensure none of the hoses are crimped and ensure the garden hose D is fully inserted A tube is fully inserted in the motor dipstick hole NOTE Motor oil should be removed when it is at room temperature al into the water source NOTE Water should be removed when it is at room temperature WARNING Should the water have suspended solids in it a strainer should be installed on that part of hose D that is in the water A piece of door screen wrapped and held with a wire tie to the end of the hose in the water source would be an example of a strainer HOMEDEPOT COM Please contact 1 800 305 1726 for further assistance Operation 1 Preparing for operation 2 Priming the pump death Never touch or handle a drill driven pump with wet little as 30 seconds can ruin it The impeller must be oiled to WARNING Risk of electric shock personal injury or j NOTE Never operate the impeller dry Operating it dry for as hands or wh
6. eing run without water or oil in the pump running the pump dry Contact the Customer Service Team at 1 800 305 1726 or visit www HomeDepot com Pre Assembly PRODUCT SPECIFICATIONS Self priming up to 8 ft vertically Lubrication Pressure lubricated bearings shaft and seal PLANNING OPERATION Carefully unpack and inspect each part Compare parts with the Package Contents list If any part appears missing or damaged do not operate this product Contact the Customer Service Team TOOLS REQUIRED Drill Garden hose 3 HOMEDEPOT COM Please contact 1 800 305 1726 for further assistance Pre Assembly continued PACKAGE CONTENTS Description Replacement Part Quantity Number OAO Oil tube 30 in x in 0 D 60DRLL003 ea l 3 in Adapter tube 3 8 in 0 D and 60DRLL005 in I D Oe P a 60DRLLOO1 o 3 ft x 1 2 in garden hose with a brass female fitting 60DRLL006 e Assembly Preparing to pump motor oil using adapter and tube WARNING Ensure drill is not connected to electrical service as you begin this process O Remove the dipstick from the engine motor from which you plan to remove motor oil Cut at a 60 angle one end of tube A From the 60 end of the tube cut a length of tube that is 1 1 2 in longer than the length of the dipstick Place the uncut end of the oil probe tube A into the adapter tube B at least 1 in or until it stops Lubricate the pump impeller by placing s
7. en standing on a wet or damp surface or in reduce friction or wear O O O water WARNING Be sure the drill is always electrically grounded to an acceptable electrical ground A NOTE Keep the suction line as short as possible and filled A with water NOTE Any air leaks in the suction line will prevent the pump from priming NOTE Never operate the pump dry for prolonged periods of time as this will damage the pump NOTE Use a strainer on the end of the inlet hose when A pumping liquids with small solids to extend pump life NOTE Oil becomes thick in cold weather Oil must be kept thin for the pump to work properly o Wet the impeller located inside the pump with pumped fluid Use the unit within the liquid temperature range of 40 F to and or cooking or mineral oil before starting the pump This 120 F improves the priming process Inspect hoses thoroughly before each use making certain that Start the drill pump Self priming should occur within 30 all connections are tight and the hoses are in good condition seconds The pump will self prime up to an 8 ft vertical lift Ensure that the inlet line 1 is airtight and submerged in fluid Ensure that liquid enters the pump within 15 to 20 seconds If The inlet 1 and discharge 2 lines should be free of kinks and not refer to the assembly instructions and also the other flow restrictions Troubleshooting section NOTE Electric drills are not
8. everal drops of mineral or vegetable oil on the impeller at inlet port 1 Place the adapter tube B into the inlet port 1 of the pump C as far as it will go Insert the end of the tube A with the 60 cut into the motor dipstick hole Attach the garden hose D to port 2 Attach the drill pump with tubes and hose to the drill Connect the drill motor power cord to a 3 wire grounded plug WARNING To minimize the pump rotating on the drill firmly grip the drill pump and hold it as you start the drill WARNING Ensure motor oil is drawn into the drill pump within 15 20 seconds to avoid damaging the pump If it does not check to ensure the tube A is firmly inserted in the adapter B and that the adapter B is firmly installed in pump C ensure the tube is not crimped and ensure the Preparing to pump clean water using garden hoses connected to the pump WARNING Ensure drill is not connected to electrical service as you begin this process O Inspect the washer in the inlet hose D to make sure it is in good condition and installed in the hose Lubricate the pump impeller by placing several drops of mineral or vegetable oil on the impeller at inlet port 1 Connect hose D to the inlet port 1 and another hose to outlet port 2 on pump C AN WARNING Keep the inlet hose as short as possible WARNING The combined height of the inlet and outlet hose should be no higher than 8 ft above the water sourc
Download Pdf Manuals
Related Search