Handy Home Products 18801-5 Instructions / Assembly
Contents
1. 3 Attach the window header LX to the top of the brackets as shown Fasten using four 3 screws 1 1 4 screws D Flush to back of frame _ 2 Nail 6 To cut opening for dormer locate the rafters on the roof Cut a hole 22 1 2 wide by 28 1 2 high Screw in as high as possible 3 Screws About 7 8 overhang 5 Attach the roof panel D using four 2 nails The roof panel should be flush to the back and centered 22 1 2 7 Center dormer over hole and attach using six 3 screws in the locations shown Screws should be driven at a slight angle to be driven into the rafters 9 Using the square edge of a table or bench bend the twelve step flashing cards F to a 90 degree angle down the center Beginning at the bottom edge of the dormer fasten the first card using roofing nails not supplied in the bottom corners only The next piece should over lay the first piece and should leave a 5 reveal attach both pieces using nails in the bottom corners only Continue process all the way up each side of the dormer Top pieces will need to be cut flush to the top of dormer using regular tin snips and fastened in all four corners 8 To attach window center in the hole and fasten using four 1 1 4 screws in the pre drilled corner holes 5 Re2. GAMBREL DORMER An attractive alternative to skylights with modern function and country appeal 16584 06 15 2006 LDR PL 1 Assemble framing brackets using pieces LY and LZ as shown Fasten using two 3 screws per bracket LY 3 Screws N x2 LZ 2 Using wall sub panel A attach brackets as shown Make sure sub panels are flush to the front and bottom of the brackets Attach using one 1 1 4 screws and two 2 nails per bracket 4 Attach waferboard spacers to the fram ing Begin with the top horizontal piece C flush to the top of the roof cleat Next attach the two vertical pieces B flush to the outside Finally attach the bottom horizontal piece C Fasten all pieces using eight 1 1 4 screws Part I D A onmoow Description Wall Sub Panel Vertical Filler Strips Horizontal Filler Strips Roof Panel Wall Panel Flashing Cards Flashing Card Horizontal Window Trim Vertical Window Trim Window Header Roof Cleat Window Side Framing Window Hardware Kit 2 Nails 1 4 Screws 2 Nails Size 3 8 x 9 x 27 7 8 3 8 x 2 7 8 x 16 3 4 3 8 x 2 x 28 3 16 3 8 x 14 x 30 3 8 x 8 3 4 x 27 1 16 4 x 32 1 x 4 x 16 1 4 1 x 3 x 29 2 x 3 x 27 1 2 2 x 3 x 24 1 8 2 x 3 x 20 1 8 Flush to front and bottom of frame
3. roof panel Paint must also be applied to trim and siding
4. veal 10 Shingle the building one complete row up past the bottom edge of the dormer 11 Using the square edge of a table or bench bend the front flashing G to slight angle about 30 degrees down the center Place against dormer and adjust angle if needed Fasten to the dormer and roof using roofing nails as shown 2 Nails 12 Attach the siding E as shown Make sure the siding is flush to the front of the dormer and flush to the underside of the roof panel Attach siding using six 2 nails per piece Siding should leave about 3 8 gap above roof to allow for shingles 13 Attach front trim using twelve 1 1 4 screws beginning with the top horizontal piece FA Make sure the trim is flush to the FB underside of the roof panel and centered on the dormer Attach the vertical trim pieces FB flush to the outside of the dormer Fi nally attach the bottom trim piece FA van ne m E 14 To shingle dormer begin at the front of 4 the roof panel and work backwards toward the roof pitch Exposure should be 5 the same as the roof Run the shingles all the way up until the dormer is covered Shingle the remainder of the building 15 Using an exterior grade caulk be sure to caulk all joints around the dormer including above and below trim and along the under side of the
Download Pdf Manuals
Related Search