Edsal 7005TN Instructions / Assembly
Contents
1. storage cabinets MODEL 6600 7000 7001 7005 7009 ASSEMBLY INSTRUCTIONS TIPS FOR INSTALLER CHECK SHIPMENT Immediately after receipt of shipment check the condition and number of packages against the packing list and bill of lading Any shortage or damage of packages should be noted on carri er s freight receipt Any claim for loss or damage must be handled by the consignee however this company will provide any necessary assis tance Shortages or errors made by this company should be reported at once DISTRIBUTE MATERIALS Check each part with parts list page 4 as they are unpacked Place parts in the approximate location where unit is to be assembled EDSAL Storage Cabinets are quality built and finished Care should be used in handling to avoid damage 6600 7000 7005 EDSAL MANUFACTURING COMPANY 4400 South Packers Ave Chicago Illinois 60609 1 i PARTS LIST FOR CABINETS 6600 7000 7001 7005 7009 IF 58 420 4 F1420N F1 EIE SIRE BB RE 3 8 2 LL F142058 1024385 Fio2an IN F142058 O 14 20Nut F1420N 10 24 3 8 Unsit Boll 1 4 20 1 2 Bolt Door Rod Guides are re Penodi Assembled to the F1420N Right Hand Door 08630005 Door Rod Guides 031385 Parts for storage cabinets also refer to Parts List on Back Page SPLIT BACK Two 2 per cabinet 6600 7000 7005 TOP A SH2. ELF l BOTTOM B NOTE Illustrated is Back in right side position DOORS CABINET SIDES Left Hand D Right Hand E yee SHELF BRACKET K Two per shelf DOOR RODS 2 F T C CC C BOLTS amp NUTS Gun Bi 10 24 X 3 8 Bolt amp Nut OM 1 4 20 x 1 2 Bolt amp Nut N O Right Hand Door H Lett Hand Door G D31395 Assembly Instructions Note Before tightening hardware check for squareness Place two Split Backs on horse or other support for eleva tion By taking one of the two Backs and turning upside down you have both a right and lett Split Back The offset edge of right Split Back should overlap offset edge ol left Split Back The two Backs should now be bolted with 10 24 x 3 8 bolts and nuts see figure A 2 The Top is now put into position Under top flanges of back and sides Using 10 24 x 3 8 bolts attach Top to Back by boll ing through from flange side see figures B amp C 3 Next bolt the right and left Cabinet Sides to right and left Back edges and to the top Use 10 24 x 3 8 bolts Top flange of Cabinet Side should be over Cabinet Top see figures A amp B 4 Position Bottom flange of Top thru the slot located on the Cabinet Sides see figure B 5 Position Cabinet Bottom between Front edges of Cabinet Sides at Lower End and Bolt with four 1 4 20 x 1 2 bolts see figures B amp D FIGURE A 6 P
3. OCKING L MODE HANDLE FOLLOWING INSTRUCTION INCLUDED FOR THIS PHASE OF INSTALL ATION
4. handle Snap locking rod guides into slots in top amp bottom of right hand door Insert locki ng rods through guides Mount locking rods to pins as shown in Fig 7 and mount cam to handle Place plate on handle and fasten with flat head screw tighten securely as shown in Fig 7 amp 8 RASTIT OOGA HOO GIES HAYE BEEN INSLUBEO FOLLOW THE INZERLENORS TO niunt PARIN ONO Oui T MOVEMENT Of LOCKING JAAS c Sus INTC Fi f PUNCA TOP COG 29 SNAPE a EOS IN Quant T REPEAT PPZCEDGTG Y NYD SLOT In Teg a fTcM BOGE GF DOOR IMAT The GUIDE 15 NSE ATED th Teg Sti p du M J NSEMY 77595 AGES TRROUN STALLED GUIDES 2ROCEED rO ATTACH RCOS YO LOCKINC t MODEL ES KAMERE FORLOWING INCLUDED FOR re p Sz OF Stat iw Afi LOCKING ROO FG B 4400 SOUTH PACKERS AVE CHICAGO ILLINOIS 80609 312 254 0600 PLASTIC DOOR ROD GUIDES HAVE BEE INCLUDED FOLLOW THE INSTRUCTIONS TO INSUR SMOOTH AND QUIET MOVEMENT OF DOO LOCKING BARS 1 INSERT PLASTIC GUIDE INTO SLO PUNCHED IN TOP EDGE OF DOOR MAK CERTAIN THAT THE GUIDE 15 FULL SEATED AND SNAPPED PAST RETAININ EDGE FORMED IN GUIDE 2 REPEAT PROCEDURE 1 INTO SLOT I THE BOTTOM EDGE OF DOOR NOT THAT THE GUIDE 15 INSERTED UPWAR IN THIS STEP 3 INSERT LOCKING RODS THROUGH Ih STALLED GUIDES AND PROCEED T ATTACH RODS TO L
5. osition Cabinet Bottom and attach to Back and Base with 10 24 x 3 8 bolts see figures B amp C T Hang right and left hand Doors to the Split Hinges welded to the Sida Bee figure A B Unit may now be set upright To install shelf first insert Shell Brackets in the adjustment slots located in the front edges of the Cabinet Ends Now insert rear corners of shell in shell adjust ment slots located at either end of back The front corners of Shell rest on and are supported by the Shell Brackets see fig ure C Direct the square cutout on the side of the Shelf to the rear of the cabinet 9 Install 3 Point Locking Handle on right side door following carefully instructions included in handle hardware package note that Locking Handle is used with 2 locking bars 10 To insure that the doors will operate properly PLACE THE CABINET IN ITS PROPER POSITION AND PLACE SHIMS UNDER THE CORNERS WHERE REQUIRED SO THE UNIT WILL BE LEVEL FIGURE C FIGURE D Front LOCKING ROD 2 3 d i Printed In Th US a 8 39x1 4 TRUSS HD SEMS SCREW 9 REQ D SUPPLIED WITH HANDLE HANDLE bo Fit 6 Tuum LT LOCKING ROD GUIDE ERES eae aaa ESE zi i Z y i PTS L sd Hg EE ICE i P i HOLDING t PLATE R n i 4 SCAM 8 32x3 8 FLAT HD MACH SCREW LO C gto Cy Ake Attach handle to right hand door as shown in Fig 6 with same screws furnished with
Download Pdf Manuals
Related Search