Home Decorators Collection 1043100410 Instructions / Assembly
Contents
1. HOME DECORATORS COLLECTION HDC 10431 MFG TW 18718WE TW 18718EO REFLECTIONS HAMPER 32 Hx17 Wx13 D ASSEMBLY INSTRUCTIONS Note Before assembly please be sure to work on a soft flat surface to avoid any damage to the finish Made In China P 1 12 BEFORE ASSEMBLY IMPORTANT NOTE READ CAREFULLY BEFORE ASSEMBLY TO PREVENT DAMAGE TO PARTS Following instruction listed below in the proper sequence as numbered to assure fast easy and correct assembly ASSEMBLY TOOLS REQUIRED DA L Screw driver Rubber Mallet Electric drill WOODEN DOWEL INSTALLATION PROCEDURE 1 FILL HOLE 1 4 FULL OF GLUE i Q 6 2 GENTLY TAP DOWEL INTO HOLE E WITH RUBBER MALLET OR USE HAND PRESS IN DO NOT USE HAMMER 3 WIPE AWAY EXCESS GLUE HIDDEN CONNECTOR ASSEMBLY TECHNIQUES FOR LOCK NUT LOCK PIN 1 SET INCLUDES C CAM LOCK 1PC A CAM BOLT 1PC TOOL NEEDED SCREW DRIVER STEP 1 SCREW CAM BOLT A ONTO PRE SET PLASTIC NUT ON PANEL USE A SCREW DRIVER FOR TIGHTENING ATTENTION DO NOT OVER TIGHTEN THE CAM BOLT A STEP 2 ATTACH BOTH PANELS MAKE SURE YOU HAVE INSERTED THE CAM BOLT TO THE VERY DEPTH OF THE HOLE WITH RUBBER MALLET GENTLY CAUTION DO NOT USE HAMMER THEN INSERT CAM LOCK C INTO PRE DRILLED HOLE ON PANEL MAKE SURE THE ARROW ON CAM LOCK C SET IN PANEL POINT TOWARD THE HOLE IN2. P 3 12 PARTS LIST BOTTOM PANEL LEG RIGHT SIDE PANEL 1 PC 4 PCS 1 PC lt gt y C LEFT SIDE PANEL TOP PANEL BACK PANEL 1 PC 1 PC 1 PC F HAMPER LEFT SIDE PANEL HAMPER RIGHT SIDE PANEL HAMPER FRONT PANEL 1 PC 1 PC 1 PC HAMPER BACK PANEL HAMPER BOTTOM PANEL FABRIC BAG 1 PC 1 PC 1 PC i NOTE THE SURFACE WITH THE STICKER IS THE BACK SIDE P 4 12 STEP 1 ASSEMBLE BOTTOM PANEL A AND LEG B e FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 USE ROUND HEAD SCREW SPRING WASHER AND FLAT WASHER 3 TO ASSEMBLE BOTTOM PANEL A AND LEG B TOGETHER BY ALLEN KEY 8 STEP 2 ASSEMBLE SIDE PANEL C amp D e USE ROUND HEAD SCREW SPRING WASHER AND FLAT WASHER 3 TO ASSEMBLE SIDE PANEL C amp D AND BOTTOM PANEL A TOGETHER BY ALLEN KEY 8 Le 0 Lo 2 gt 3 P 5 12 STEP 3 ASSEMBLE TOP PANEL E e FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 e USE CAM BLOT CAM LOCK 2 TO ASSEMBLE SIDE PANEL C D AND TOP PANEL E TOGETHER P 6 12 STEP A ASSEMBLE BACK PANEL F e USE ROUND HEAD SC
3. ASSEMBLE PREVENT DEVICE 8 e USE ELECTRIC DRILL TO DRILL 2 SMALL HOLES ON THE DESIRED LOCATION OF WALL INSERT 2 GECKOS INTO THE 2 HOLES BY RUBBER MALLET USE TWO LONG SCREWS TO ATTACH ONE PLASTIC SLICE ONTO WALL THEN USE TWO SHORT SCREWS TO ATTACH ANOTHER PLASTIC SLICE ON THE BACK OF PRE ASSEMBLED PRODUCT e USE THE PLASTIC ROPE TO LINK THE PRODUCT AND WALL TOGETHER WARNING THE TILTING PREVENT HARDWARE MUST BE USED AS A PART OF ASSEMBLY OTHERWISE TILTING DANGER MAY BE CAUSED SQ WALL N gt e AN Zi A JAS 6 AN AA 7 Se N z 5 Se N on N RN N NO SU P 12 12
4. REW 6 TO ATTACH BACK PANEL F ON THE BACK OF PRE ASSEMBLED UNIT NOTE BEFORE YOU ASSEMBLE THE BACK PANEL PLEASE MAKE SURE THE 2 SIDE PANELS HAVE AN EVEN GAP BETWEEN THEM IF UNEVEN SHIFT THE SIDE PANELS UNTIL EVENLY SPACED THEN ATTACH BACK PANEL P 7 12 STEP 5 ASSEMBLE HAMPER SIDE PANEL G H AND HAMPER FRONT PANEL I e USE CAM BLOT amp CAM LOCK 2 TO ASSEMBLE HAMPER SIDE PANEL G H AND HAMPER FRONT PANEL 1 TOGETHER AS SHOWN STEP 6 ASSEMBLE HAMPER BACK PANEL J AND HAMPER BOTTOM PANEL K e INSERT THE HAMPER BOTTOM PANEL K INTO SLOTS ON HAMPER SIDE PANELS G H e USE FLAT HEAD SCREW 4 TO ASSEMBLE HAMPER BACK PANEL J AND HAMPER SIDE PANEL G amp H TOGETHER AS SHOWN P 8 12 STEP 7 PLACE HAMPER e PLACE THE SLOTS ON THE BOTTOM OF THE HAMPER ONTO THE WOOD DOWELS 1 PROPERLY AS SHOWN P 9 12 STEP 8 ASSEMBLE BOLT 7 AND KNOB 5 e TIGHTEN BOLT 7 ONTO SIDE PANEL C D PROPERLY AS SHOWN e USE ROUND HEAD BOLT 5 TO ATTACH KNOB 5 ONTO HAMPER FRONT PANEL I P 10 12 STEP 9 PLACE FABRIC BAG L e PUT FABRIC BAG L INTO THE HAMPER AND THEN STICK THE MAGIC TAPE PROPERLY P 11 12 STEP 10
5. TO WHICH THE CAM BOLT A HAS BEEN INSERTED AND INSERTED THE CAM LOCK C TO THE VERY DEPTH OF THE HOLE STEP 3 ROTATE THE CAM LOCK C CLOCKWISE TO SECURE CAM BOLT A BY TIGHTENING WITH A A7 SCREWDRIVER DETAIL STEP PLEASE SEE THE BELOW PICTURE P 2 12 VERTICAL CONNECTION HORIZONTAL CONNECTION 1 La 2 1 La 2 O SO e 4 3 4 SPa amp 5 THANK YOU FOR PURCHASING THIS QUALITY PRODUCT BE SURE TO CHECK ALL PACKING MATERTAL CAREFULLY FOR SMALL PARTS WHICH MAY HAVE CAME LOOSE INSIDE THE CARTON DURING SHIPMENT COUNT ALL PARTS AND MATERIAL HARDWARE COMPARE WITH PARTS LIST TO BE SURE ALL PART ARE PRESENT IF ANY PARTS ARE MISSING OR DAMAGED PHONE FAX OR MAIL TO OUR CUSTOMER SERVICE DEPARTMENT FOR EFFICIENT AND SPEEDY SERVICE PLEASE INDICATE THE MODEL NUMBER AND CODE LETTER OF THE PART NEEDED IMPORTANT NOTE FOLLOW INSTRUCTIONS LISTED BELOW IN PROPER SEQUENCE AS NUMBERED TO ASSURE FAST EASY AND CORRECT ASSEMBLY HARDWARE LIST WOOD CAM BOLT ROUND HEAD BOLT FLAT HEAD SCREW KNOB DOWEL CAM LOCK FLAT WASHER 6 PCS BOLT 10 PCS 8 SETS SPRING WASHER 1 SET 8 SETS 0 mo Y amp O 08 x 30mm 1 2 06 x 32mm 3 4x 25mm 4 93x19mm 5 ROUND HEAD BOLT ALLEN KEY TILTING PREVENT HARDWARE SCREW 2 PCS 1 PC 13 PCS ng Sg 3 x 12mm 6 6 x 25mm 7 8 3x12mm 04x 45mm 9 GLUE 1PC 10
Download Pdf Manuals
Related Search