Bullet Tools 520 Instructions / Assembly
Contents
1. 2 0175 for return instructions BULLETPROOF WARRANTY GOLD 5 Year Bullet Tools warrants only to the original purchaser of this product when purchased from an authorized reseller or distributor that this product will be free from defects in material and workmanship under normal use and service for five 5 years from initial purchase This warranty includes all parts except the blade and cosmetic appearance chips dings scratches caused by normal use and wear This warranty does not cover any damage due to accident misuse abuse or negligence Further it is valid only if the product is used with the cut products specified in the cut guide Please refer to the User Guide for details or call Bullet Tools technical support In order to recover under this limited warranty the purchaser must make claim to Bullet Tools within 60 days of occurrence and must present acceptable proof of original ownership such as original receipt warranty card registration on line registration or other documentation Bullet Tools deems acceptable for the product Bullet Tools at its option shall repair or replace the defective unit covered by this warranty To obtain warranty service please contact Bullet Tools at 1 800 406 8998 or 1 208 772 0175 for pre authorization and further instructions Bullet Tools disclaims all warranties express or implied including all warranties of merchantability and or fitness for a particular purpose Additional2. USER GUIDE Read Before Use RCT 526 RCT 520 LL eee ee es Butte 1UULo tw Cutting Edge Solutions for Tradesmen www BulletTools com 208 772 0175 PRT INS 5RCT RevA 11 13 2013 Bullet Tools AWARNING VERY SHARP BLADE WARNING FAILURE TO FOLLOW THIS GUIDE MAY RESULT IN SERIOUS INJURY USING THIS MACHINE WITH RESPECT AND CAUTION WILL CONSIDERABLY REDUCE THE RISK OF PERSONAL INJURY SAFETY GUIDE FOR THE MAGNUM RCT SERIES 1 READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE OPERATING THE RCT 2 If you are not thoroughly familiar with the operation of the RCT Shear obtain advice from a qualified instructor or call 800 406 8998 Intl 208 772 0175 3 Stay alert Do not operate while under the influence of drugs alcohol or medication 4 Always wear safety approved eye protection with side shields ANSI Z87 1 5 Keep work area clean and free of debris 6 Recommended operating temperature range 20 F 6 C to 115 F 46 C 7 Keep children and unauthorized persons away from the Shear and work area 8 Make sure tool is secure Operate only on a firm substrate or solid stand 9 Use the right tool Do not force the RCT Shear or use it for a job for which it was not intended the RCT Shear is designed to cut carpet tile VCT LVT PVC tile vinyl tile amp residential grade low pressure laminate flooring See Cut Guide page 7 10 Keep Blade sharp A dull Bl
3. ade will not perform properly _ _ Always keep hands away from Blade while operating or carrying 12 Do not alter or misuse this tool The RCT Shear is precision built modifications not specified in this manual may result in a dangerous condition 13 Maintain RCT Shear with care Keep Blade sharp and clean Follow instructions for lubricating and changing accessories See page 7 P Use only recommended accessories The use of improper accessories may cause hazards or injury 5 Never leave the RCT Shear unattended Secure the Handle with the Safety Lock when not in use See page 6 O Warning The dust generated by cutting certain wood wood fiber and or PVC products can be hazardous to your health The RCT Shear generally does not produce any dust however minimal creation of dust may be possible Avoid ingesting any dust created through cutting AWARNING 520 SET UP WELCOME YOUR MAGNUM RCT SHEAR COMES READY TO ASSEMBLE Please Review and Verify Parts Included in Box You will need 2 amp 3 Phillips head screwdrivers anda 1 2 13mm socket or wrench 1 Power Assembly 1a Safety Lock pin 2 Handle Assembly 3 Table 4 Tail 5 Rails 2 6 Angle Guide 7 Hone Stone 8 Hardware Kit HARDWARE KIT 4 6mm x 60mm PH Phillips Machine Screws 4 M6 Star Washers 4 6mm x 25mm PH Phillips Machine Screws 5 M6 x 16mm FH Phillips Machine Screws 4 10 x 1 FH Phillips Sel
4. ease note Approved materials may vary in density and hardness If extreme pressure is required to cut a product it may result in damage to your machine Please contact Bullet Tools before proceeding Warranty is void if an unapproved product damages the machine AN AWARNING VERY SHARP BLADE Do NOT Use on High Pressure Laminate or Solid Wood Replacement Blade for RCT520 is part 520B Replacement Blade for RCT526 is part 526B MAINTENANCE Honing the Blade Hone every 100 cuts Push the handle down until blade is 1 4 6mm open Lay the hone stone against the flat face of the blade side toward the table Slide from end to end 2 or 3 times Greasing Lubricating Grease After every 100 cuts lubricate the wear points of the pins and the bearings as shown Use a light oil i e 10W motor oil This will prevent the machine from wearing out prematurely Apply grease wheel bearing grease frequently to the bearings where indicated WARRANTY 30 Day Satisfaction Guarantee Bullet Tools is confident that you will be absolutely pleased with the purchase of our product If for any reason you are not completely satisfied with your tool we will refund your purchase price at any time within 30 days of your original purchase receipt required If you want to return your product under our 30 day no risk trial offer valid only for purchases made in the US please contact us at 1 800 406 8998 or 208 77
5. f Tapping Screws 2 M8 x 50mm Hex Bolts 1 M6 Thumbscrew ASSEMBLY 1 ATTACH RAILS 2 ATTACH TAIL Attach rails to Power Assembly base using Item A Attach tail to rails using Item C machine screws machine screws fitted with Item B star washers Make sure holes in tail are facing up AWARNING 526 SET UP WELCOME YOUR MAGNUM RCT SHEAR COMES READY TO ASSEMBLE Please Review and Verify Parts Included in Box You will need 2 amp 3 Phillips head screwdrivers anda 1 2 13mm socket or wrench 1 Power Assembly 1a Safety Lock pin 2 Handle Assembly 3 Table 4 Tail 5 Rails 4 6 Angle Guide 7 Hone Stone 8 Hardware Kit HARDWARE KIT 8 6mm x 65mm PH Phillips Machine Screws 8 M6 Star Washers 8 6mm x 25mm PH Phillips Machine Screws 6 M6 x 16mm FH Phillips Machine Screws 4 10 x 1 FH Phillips Self Tapping Screws 2 M8 x 50mm Hex Bolts 1 M6 Thumbscrew ASSEMBLY 1 ATTACH RAILS 2 ATTACH TAIL Attach rails to Power Assembly base using Item A Attach tail to rails using Item C machine screws machine screws fitted with Item B star washers Make sure holes in tail are facing up SET UP 3 ATTACH TABLE A Attach front of table to base using Item D screws Tighten with 3 Phillips B Attach back of table to tail using Item E self tapping screws Tighten with 2 Phillips 4 TO ATTACH HANDLE Insert Item F screws and tighten with 1 2 13mm wrench Note To ens
6. rights may be available under the laws of your state or province Any and all warranties written or implied are void with any alterations to the product Note Bullet Tools shall not be liable for any special incidental or consequential damages including but not limited to lost revenue lost profits rental or replacement equipment downtime damage to property and third party claims arising out of any theory of recovery including warranty contract statutory or tort ULLE I I UULS Cutting Edge Solutions for Tradesmen b www BulletTools com 1 208 772 0175
7. ure correct alignment start each of the bolts by hand before using wrench 5 ATTACH ANGLE GUIDE Install angle guide and tighten tem G thumbscrew AN AWARNING MAKING CUTS AWARNING Caution Wear hand and eye protection while operating the EZ Shear While gently pushing handle down pull Safety Lock pin out then lift handle Pull Safety Lock pin Place product on table Bring handle down until blade Push the handle down touches material oo a until the material is P completely cut lt a cA DO NOT USE ON HIGH PRESSURE LAMINATE OR SOLID WOOD WARNING Blade is very sharp Keep fingers away from blade Most materials listed on page 6 shear cleanly with just one cut However some types of laminate flooring and fiber cement siding may require cutting twice to produce a better cut DOUBLE CUTTING Simply make your first cut 1 8 to 1 4 3mm to 6mm longer than your mark and then make a second cut on your mark This is very useful to create a cleaner cut on exposed ends or when you cannot cover the cut edge with molding or trim 5 Your RCT Shear cuts a wide variety of products Please refer to this cut guide for recommended products and thicknesses RCT CUT GUIDE 520 Maximum Thickness 15mm or 5 8 526 Maximum Thickness 25mm or 1 Material Carpet Tile Commercial Vinyl Tile Luxury Vinyl Tile Parquet PVC Tile Rubber Cove Base Rubber Tile Soft Plastic Garage Tile Pl
Download Pdf Manuals
Related Search